Hi there, I'm trying to reduce power consumption by replacing my old server with a newer Alix1C. Both systems are running an up-to-date Gentoo (ivtv-1.0.3-r2) and the same kernel (gentoo-sources 2.6.23-r8); I will reuse my PVR150 in the new system. However, when the ivtv is initialized on the new system, it seems it doesn't detect the tuner part, which I found out comparing the dmesg's on both machines. This part I only see on the old one:
tuner 0-0043: chip found @ 0x86 (ivtv i2c driver #0) tda9887 0-0043: tda988[5/6/7] found @ 0x43 (tuner) tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) tuner 0-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) I also tried to reuse the .config of the old machine, but this didn't help. I'm quite sure the actual capturing works but didn't test the composite/s-video yet to prove it. When I try to set a frequency, I still see the same black screen with a tiny bit of static and no 'Signal Detected'; ~ # v4l2-ctl -f 245.250 Frequency set to 3924 (245.250000 MHz) ~ # v4l2-ctl -F Frequency: 0 (0.000000 MHz) ~ # ivtv-tune -t europe-west -x TV1 /dev/video0: 203.250 MHz When I perform the first command, I see additional output in dmesg; wm8775 0-001b: I2C: cannot write 0c0 to register R21 wm8775 0-001b: I2C: cannot write 1d4 to register R14 wm8775 0-001b: I2C: cannot write 1d4 to register R15 wm8775 0-001b: I2C: cannot write 102 to register R21 A friend is also using a pvr150 on his Alix1C (Debian) without problems. - relevant lsmod: wm8775 4524 0 cx25840 21488 0 tuner 56072 0 ivtv 112016 0 firmware_class 6688 2 cx25840,ivtv i2c_algo_bit 4772 1 ivtv cx2341x 9924 1 ivtv tveeprom 13264 1 ivtv i2c_core 17744 6 wm8775,cx25840,tuner,ivtv,i2c_algo_bit,tveeprom videodev 23840 1 ivtv v4l2_common 14304 6 wm8775,cx25840,tuner,ivtv,cx2341x,videodev v4l1_compat 12164 2 ivtv,videodev - dmesg from the problem machine: ivtv: Start initialization, version 1.0.0 ivtv0: Initializing card #0 ivtv0: Autodetected Hauppauge card (cx23416 based) ACPI: PCI Interrupt Link [LNKC] BIOS reported IRQ 0, using IRQ 10 ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10 ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10 ivtv0: Loaded v4l-cx2341x-enc.fw firmware (376836 bytes) ivtv0: Encoder revision: 0x02060039 tveeprom 0-0050: Hauppauge model 26559, rev F189, serial# 9929952 tveeprom 0-0050: tuner model is TCL MFPE05 2 (idx 89, type 38) tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 0x74) tveeprom 0-0050: audio processor is CX25843 (idx 37) tveeprom 0-0050: decoder processor is CX25843 (idx 30) tveeprom 0-0050: has radio, has no IR receiver, has no IR transmitter ivtv0: Autodetected Hauppauge WinTV PVR-150 cx25840 0-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #0) cx25840 0-0044: loaded v4l-cx25840.fw firmware (16382 bytes) ivtv0: i2c hardware 0x00000020 (wm8775) not found for command 0x4008646d ivtv0: Registered device video0 for encoder MPEG (4 MB) ivtv0: Registered device video32 for encoder YUV (2 MB) ivtv0: Registered device vbi0 for encoder VBI (1 MB) ivtv0: Registered device video24 for encoder PCM audio (1 MB) ivtv0: Registered device radio0 for encoder radio ivtv0: Initialized card #0: Hauppauge WinTV PVR-150 ivtv: End initialization Any help would be appreciated. Kind regards, Jan _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
