Hi Alex, Please get this archive:
http://linuxtv.org/hg/%7Ehverkuil/v4l-dvb-newcards/archive/tip.tar.bz2 It contains an initial card definition for the new-style PVR-550. Build instructions are the same as for the bleeding edge driver: http://www.ivtvdriver.org/index.php/Download#Bleeding_Edge_driver Since this card cannot be autodetected you will have to specify the module option 'cardtype=27'. See which inputs work and which do not and let me know the results. BTW, you mentioned cardtype 53. I'm not sure what you meant with that since there is no cardtype 53. I suspect you meant the old diamond PVR-550 cardtype which uses *tuner* type 53. Depending on the results I will follow-up with additional instructions on how to find the right combination of values, but I think it is likely that this will work. Regards, Hans On Wednesday 13 August 2008 03:33:54 Alex Lowe wrote: > Hi again, > > Here's the output of lspci -v > > 00:0b.0 Multimedia video controller: Internext Compression Inc iTVC16 > (CX23416) MPEG-2 Encoder (rev 01) > Subsystem: Unknown device ff92:0070 > Flags: bus master, medium devsel, latency 64, IRQ 10 > Memory at e0000000 (32-bit, prefetchable) [size=64M] > Capabilities: [44] Power Management version 2 > > As far as I can tell, it's indistinguishable from the version 1 > except that the tuner doesn't work. Of course, I couldn't find any > lspci output from the version 1. > > Alex > > On 12 Aug 2008, at 01:31 , Hans Verkuil wrote: > > On Monday 11 August 2008 08:41:29 Alex Lowe wrote: > >> Hi, > >> > >> I have revision 2 of the Diamond PVR-550 card (the one with the > >> tuner that doesn't work by default). > > > > Does this revision have the same PCI IDs? That is, with an > > unmodified driver it is still autodetected as a Diamond PVR-550? > > > > Regards, > > > > Hans > > > >> I've managed to get the tuner to work by downloading the latest > >> mercurial version of v4l-dvb (http://www.linuxtv.org) and forcing > >> cardtype=20 > >> With that I can use the tuner normally. However, I can't use the > >> S- Video or Composite inputs. > >> When I set cardtype=53, I can use the composite/s-video inputs, > >> but no tuner. > >> > >> After some playing around (actually, changing the code, because I > >> couldn't find what card numbers and tuner numbers each one was > >> except in the code), I would up with the following (from dmesg): > >> > >> [ 4214.864774] ivtv: Start initialization, version 1.4.0 > >> [ 4214.865411] ivtv0: Initializing card #0 > >> [ 4214.865437] ivtv0: Autodetected Yuan PG600, Diamond PVR-550 > >> card (cx23416 based) > >> [ 4214.868141] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKD] > >> -> GSI 10 (level, low) -> IRQ 10 > >> [ 4214.895336] cx25840 0-0044: cx25843-24 found @ 0x88 (ivtv i2c > >> driver #0) > >> [ 4214.898189] tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver > >> #0) [ 4214.898333] xc2028 0-0061: creating new instance > >> [ 4214.898338] xc2028 0-0061: type set to XCeive xc2028/xc3028 > >> tuner [ 4218.361498] cx25840 0-0044: loaded v4l-cx25840.fw > >> firmware (16382 bytes) > >> [ 4218.435613] ivtv0: Registered device video0 for encoder MPG > >> (4096 kB) [ 4219.123362] ivtv0: Loaded v4l-cx2341x-enc.fw firmware > >> (376836 bytes) [ 4219.322102] ivtv0: Encoder revision: 0x02060039 > >> [ 4219.435678] xc2028 0-0061: Loading 80 firmware images from > >> xc3028- v27.fw, type: xc2028 firmware, ver 2.7 > >> [ 4219.441856] xc2028 0-0061: Loading firmware for type=BASE (1), > >> id 0000000000000000. > >> [ 4219.451003] i2c-adapter i2c-0: sendbytes: error - bailout. > >> [ 4219.451329] xc2028 0-0061: i2c output error: rc = -14 (should > >> be 64) [ 4219.451336] xc2028 0-0061: -14 returned from send > >> [ 4219.451341] xc2028 0-0061: Error -22 while loading base > >> firmware [ 4219.514126] xc2028 0-0061: Loading firmware for > >> type=BASE (1), id 0000000000000000. > >> [ 4219.522883] i2c-adapter i2c-0: sendbytes: error - bailout. > >> [ 4219.523318] xc2028 0-0061: i2c output error: rc = -14 (should > >> be 64) [ 4219.523326] xc2028 0-0061: -14 returned from send > >> [ 4219.523331] xc2028 0-0061: Error -22 while loading base > >> firmware [ 4219.561657] xc2028 0-0061: Loading firmware for > >> type=BASE (1), id 0000000000000000. > >> [ 4219.570815] i2c-adapter i2c-0: sendbytes: error - bailout. > >> [ 4219.571133] xc2028 0-0061: i2c output error: rc = -14 (should > >> be 64) [ 4219.571141] xc2028 0-0061: -14 returned from send > >> [ 4219.571146] xc2028 0-0061: Error -22 while loading base > >> firmware [ 4219.633557] xc2028 0-0061: Loading firmware for > >> type=BASE (1), id 0000000000000000. > >> [ 4219.642717] i2c-adapter i2c-0: sendbytes: error - bailout. > >> [ 4219.643048] xc2028 0-0061: i2c output error: rc = -14 (should > >> be 64) [ 4219.643056] xc2028 0-0061: -14 returned from send > >> [ 4219.643060] xc2028 0-0061: Error -22 while loading base > >> firmware [ 4219.643666] ivtv0: Registered device video32 for > >> encoder YUV (2048 kB) > >> [ 4219.643694] ivtv0: Registered device vbi0 for encoder VBI (1024 > >> kB) [ 4219.643717] ivtv0: Registered device video24 for encoder > >> PCM (320 kB) [ 4219.643721] ivtv0: Initialized card #0: Yuan > >> PG600, Diamond PVR-550 [ 4219.643753] ivtv: End initialization > >> > >> As you can see, It uses the Diamond PVR-550 card (#53) now with > >> the xc2028 tuner (the tuner in #20 - I think it's tuner #71?) > >> > >> Now the tuner, once again, no longer works (although at one point > >> with this setup it did). > >> > >> Is there any way I can modify it so that I can use the Composite > >> and S- Video from the PVR-550 (#53) and still have the (full, > >> channel- changing) tuner using the xc2028 driver (#71)? > >> I would happily submit a patch if I need to change the code (NOTE: > >> I am not a good coder, but I would at least be able to write > >> something that would be fixable into reasonable C). > >> > >> Thanks in advance, > >> > >> Alex Lowe > > > > _______________________________________________ > > ivtv-users mailing list > > [email protected] > > http://ivtvdriver.org/mailman/listinfo/ivtv-users _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
