I have 2 Ubuntu systems which are not identicle. I installed the Hauppauge HVR 1600 in system A (my testing system). I followed the info from the Ubuntu forum. The card was detected. So I performed the same steps on system B ( my working system). Again, the card was detected.
Here is the result from dmesg | grep cx18... [EMAIL PROTECTED]:~$ dmesg | grep cx18[ 33.453263] cx18: Start initialization, version 1.0.0 [ 33.453344] cx18-0: Initializing card #0 [ 33.453347] cx18-0: Autodetected Hauppauge card [ 33.453686] cx18-0: Unreasonably low latency timer, setting to 64 (was 32) [ 33.454847] cx18-0: cx23418 revision 01010000 (B) [ 33.638188] cx18-0: Autodetected Hauppauge HVR-1600 [ 33.638190] cx18-0: VBI is not yet supported [ 33.875988] tuner 3-0061: chip found @ 0xc2 (cx18 i2c driver #0-1) [ 33.876008] cs5345 2-004c: chip found @ 0x98 (cx18 i2c driver #0-0) [ 34.359582] cx18-0: Disabled encoder IDX device [ 34.359622] cx18-0: Registered device video0 for encoder MPEG (2 MB) [ 34.359625] DVB: registering new adapter (cx18) [ 34.481415] cx18-0: DVB Frontend registered [ 34.481436] cx18-0: Registered device video32 for encoder YUV (2 MB) [ 34.481451] cx18-0: Registered device video24 for encoder PCM audio (1 MB) [ 34.481454] cx18-0: Initialized card #0: Hauppauge HVR-1600 [ 34.481472] cx18: End initialization [ 39.780923] cx18-0: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes) [ 40.254019] cx18-0: loaded v4l-cx23418-cpu.fw firmware (174716 bytes) [ 40.259021] cx18-0: FW version: 0.0.71.0 (Release 2006/12/29) [ 41.065204] cx18-0: loaded v4l-cx23418-dig.fw firmware (16382 bytes) Now, I have the card detected on system B where I want to use it. So for further testing I reinstalled Ubuntu on system A and reinstalled the card. dmesg | grep cx18 now gives a differant result. Here is the result... [EMAIL PROTECTED]:~$ dmesg | grep cx18 [ 35.337116] cx18: Start initialization, version 1.0.0 [ 35.337183] cx18-0: Initializing card #0 [ 35.337186] cx18-0: Autodetected Hauppauge card [ 35.337538] cx18-0: Unreasonably low latency timer, setting to 64 (was 32) [ 35.338747] cx18-0: cx23418 revision ffffffff (A) [ 35.494047] cx18-0: Invalid EEPROM [ 35.494049] cx18-0: VBI is not yet supported [ 35.725689] cs5345 2-004c: chip found @ 0x98 (cx18 i2c driver #0-0) [ 35.727388] cx18-0: Disabled encoder IDX device [ 35.727420] cx18-0: Registered device video0 for encoder MPEG (2 MB) [ 35.727422] DVB: registering new adapter (cx18) [ 35.886616] cx18-0: frontend initialization failed [ 35.886795] cx18-0: DVB failed to register [ 35.886828] cx18-0: Registered device video32 for encoder YUV (2 MB) [ 35.886844] cx18-0: Registered device video24 for encoder PCM audio (1 MB) [ 35.886861] cx18-0: Registered device radio0 for encoder radio [ 35.887115] cx18-0: Error -12 registering devices [ 35.888619] cx18-0: Error -12 on initialization [ 35.888639] cx18: probe of 0000:01:06.0 failed with error -12 [ 35.888665] cx18: End initialization What does this new dmesg result indicate and what should I do to correct it? I want to perfect it on the testing system before I do any more configuring on the working system, and therefore I must understand the problem. _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
