Update... Well tried to build a custom 2.6.23.2 kernel.. Failed miserably due to the fact I couldnt get my NAT to work. If anyone knows where I could possibly get a 2.6.20+ Kernel version. Currently I am using 2.6.18-128.1.6 RPM from CentOS 5.3. I have installed ivtv-0.10.6 w/o issue. Driver seems to work.
Here is the debug I get from dmesg. ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.10.6 (tagged release) loading ivtv: Linux version: 2.6.18-128.1.6.el5 SMP mod_unload 686 REGPARM 4KSTACKS gcc-4.1 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected Hauppauge card (cx23416 based) ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 16 (level, low) -> IRQ 201 ivtv0: Unreasonably low latency timer, setting to 64 (was 32) ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) ivtv0: Encoder revision: 0x02060039 tveeprom 1-0050: Hauppauge model 26032, rev C199, serial# 8297123 tveeprom 1-0050: tuner model is TCL 2002N 5H (idx 99, type 50) tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08) tveeprom 1-0050: audio processor is CX25841 (idx 35) tveeprom 1-0050: decoder processor is CX25841 (idx 28) tveeprom 1-0050: has no radio, has IR remote ivtv0: Autodetected Hauppauge WinTV PVR-150 ivtv0: reopen i2c bus for IR-blaster support tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0) cx25840 1-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0) cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes) wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0) ivtv0: Registered device video0 for encoder MPEG (4 MB) ivtv0: Registered device video32 for encoder YUV (2 MB) ivtv0: Registered device vbi0 for encoder VBI (1 MB) ivtv0: Registered device video24 for encoder PCM audio (1 MB) tuner 1-0061: type set to 50 (TCL 2002N) ivtv0: Initialized Hauppauge WinTV PVR-150, card #0 ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 209 PCI: Setting latency timer of device 0000:00:11.5 to 64 ivtv: ==================== END INIT IVTV ==================== I have ran the debug of cat /dev/video0 > /tmp/test.mpg and found it wasnt producing anything. I have ran the config tools and set it to tuner0 and chanel 53. When I ran the config on mythtv it said it found all of the channels and the signal was at 98%.. So Im confused.. Any ideas? Brian On Fri, May 1, 2009 at 7:06 PM, Brian Fertig <[email protected]> wrote: > Greetings all.. > > Im not sure what to provide for my issue but I will let you know what I am > dealing with.. > > > Basically I got everything setup. It found all of my channels and signal > strengths. I did what the IVTV documentation said and did a cat /dev/video0 > > /tmp/bla.mpg > > When I check the file its 0 bytes.. I have ran the ivtv tools and set it > to a channel and forced tuner0. What am I doing wrong here? Let me know > what you need and I will post it up. > > > Brian
_______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
