Thanks for your help so far. With me juggling settings it is now video0 still
no audio. I checked all of the options under the advanced volume control and
no luck. Here is the output for the card. I see a few things that sand out
that might be nothing or might be the issue. "no detected audio standard" is
one "audio muted yes" is another ant the last is the "audio microcontroller:
stopped". I looked up the mute command for v4l2-ctl and tried that as well but
no luck.
cx18-0: ================= START STATUS CARD #0 =================
cx18-0: Version: 1.2.0 Card: Hauppauge HVR-1600
tveeprom 0-0050: Hauppauge model 74041, rev C6B2, serial# 937559
tveeprom 0-0050: MAC address is 00-0D-FE-0E-4E-57
tveeprom 0-0050: tuner model is TCL M2523_5N_E (idx 112, type 50)
tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 0-0050: audio processor is CX23418 (idx 38)
tveeprom 0-0050: decoder processor is CX23418 (idx 31)
tveeprom 0-0050: has no radio, has IR receiver, has IR transmitter
cx18-0 843: Video signal: present
cx18-0 843: Detected format: NTSC-M
cx18-0 843: Specified standard: NTSC-M
cx18-0 843: Specified video input: Composite 7
cx18-0 843: Specified audioclock freq: 32000 Hz
cx18-0 843: Detected audio mode: mono
cx18-0 843: Detected audio standard: no detected audio standard
cx18-0 843: Audio muted: yes
cx18-0 843: Audio microcontroller: stopped
cx18-0 843: Configured audio standard: automatic detection
cx18-0 843: Configured audio system: BTSC
cx18-0 843: Specified audio input: Tuner (In8)
cx18-0 843: Preferred audio mode: stereo
cx18-0 gpio-reset-ctrl: GPIO: direction 0x00003001, value 0x00003001
tuner 1-0061: Tuner mode: analog TV
tuner 1-0061: Frequency: 61.25 MHz
tuner 1-0061: Standard: 0x0000b000
cs5345 0-004c: Input: 1
cs5345 0-004c: Volume: 0 dB
cx18-0: Video Input: Tuner 1
cx18-0: Audio Input: Tuner 1
cx18-0: GPIO: direction 0x00003001, value 0x00003001
cx18-0: Tuner: TV
cx18-0: Stream: MPEG-2 Program Stream
cx18-0: VBI Format: No VBI
cx18-0: Video: 720x480, 30 fps
cx18-0: Video: MPEG-2, 4x3, Variable Bitrate, 4500000, Peak 6000000
cx18-0: Video: GOP Size 15, 2 B-Frames, GOP Closure
cx18-0: Audio: 32 kHz, MPEG-1/2 Layer II, 384 kbps, Stereo, No Emphasis, No
CRC
cx18-0: Spatial Filter: Manual, Luma 1D Horizontal, Chroma 1D Horizontal, 0
cx18-0: Temporal Filter: Manual, 8
cx18-0: Median Filter: Off, Luma [0, 255], Chroma [0, 255]
cx18-0: Status flags: 0x00200001
cx18-0: Stream encoder MPEG: status 0x0000, 0% of 2048 KiB (64 buffers) in
use
cx18-0: Stream encoder YUV: status 0x0000, 0% of 2048 KiB (16 buffers) in use
cx18-0: Stream encoder VBI: status 0x0000, 0% of 1015 KiB (20 buffers) in use
cx18-0: Stream encoder PCM audio: status 0x0000, 0% of 1024 KiB (256
buffers) in use
cx18-0: Read MPEG/VBI: 47030272/0 bytes
cx18-0: ================== END STATUS CARD #0 ==================
> From: [email protected]
> To: [email protected]
> Date: Thu, 20 Aug 2009 22:36:07 -0400
> Subject: Re: [ivtv-users] cx18 anlog tv tuner picture but now audio
>
> On Thu, 2009-08-20 at 21:09 -0400, Jayme Shaffer wrote:
> > Im using a HVR-1600 in Fedora 11 x64. I previously had the card
> > working flawlessly in Fedora 10 32-bit. I have tried grabbing the
> > latest firmware as well as drivers. I can see in /var/log/messages
> > that the card is being initialized. But when I do a cat /dev/video1 >
> > test.mpg I get video but no audio.
>
> Make sure the audio volume is up. Use the "Advanced Volume Control" app
> that's buried somewhere under the system menu. (Fedora 11 is such a
> hassle for something this basic...)
>
> Also could you provide the output of
>
> $ v4l2-ctl -d /dev/video1 --log-status
>
> when tuned to a good station.
>
>
> > I use it with MythTV and in the backend log all that can be found
> > when switching to the analog tunere is "Not IVTV Driver??"
>
> Well, truth be told, the cx18 driver doesn't behave exactly like the
> ivtv driver, so MythTV notices at times. :)
>
> Those messages are harmless, IIRC. I use MythTV all the time.
>
> Regards,
> Andy
>
> > here is the output for lspci -v
> > 01:05.0 Multimedia video controller: Conexant Systems, Inc. CX23418
> > Single-Chip MPEG-2 Encoder with Integrated Analog Video/Broadcast
> > Audio Decoder
> > Subsystem: Hauppauge computer works Inc. WinTV HVR-1600
> > Flags: bus master, medium devsel, latency 64, IRQ 16
> > Memory at d4000000 (32-bit, non-prefetchable) [size=64M]
> > Capabilities: [44] Vital Product Data
> > Capabilities: [4c] Power Management version 2
> > Kernel driver in use: cx18
> > Kernel modules: cx18
> > Please help. Thanks, Jayme
> >
> >
> > ______________________________________________________________________
>
>
> _______________________________________________
> ivtv-users mailing list
> [email protected]
> http://ivtvdriver.org/mailman/listinfo/ivtv-users
_________________________________________________________________
Get back to school stuff for them and cashback for you.
http://www.bing.com/cashback?form=MSHYCB&publ=WLHMTAG&crea=TEXT_MSHYCB_BackToSchool_Cashback_BTSCashback_1x1
_______________________________________________
ivtv-users mailing list
[email protected]
http://ivtvdriver.org/mailman/listinfo/ivtv-users
