Hi,
I could flash image in emmc using uuu tool. Removed sd card from board.
Facing bootup failing if using "run jh_mmcboot". Image boot up successfully
if don't use this. Tried the same in sd card it works properly, what could
be the reason for failing image in emmc.Logs are below:
U-Boot SPL 2020.04-5.4.24-2.1.0+g4979a99 (Jul 28 2020 - 11:44:33 +0000)
PMIC: PFUZE100 ID=0x10
DDRINFO: start DRAM init
DDRINFO: DRAM rate 3200MTS
DDRINFO:ddrphy calibration done
DDRINFO: ddrmix config done
Normal Boot
Trying to boot from MMC1
E/TC:0 0 caam_mp_init:367 *************************************
E/TC:0 0 caam_mp_init:368 * Warning: Manufacturing protection *
E/TC:0 0 caam_mp_init:369 * is not supported *
E/TC:0 0 caam_mp_init:370 *************************************
U-Boot 2020.04-5.4.24-2.1.0+g4979a99 (Jul 28 2020 - 11:44:33 +0000)
CPU: i.MX8MQ rev2.0 1500 MHz (running at 1000 MHz)
CPU: Commercial temperature grade (0C to 95C) at 36C
Reset cause: POR
Model: NXP i.MX8MQ EVK
DRAM: 3 GiB
TCPC: Vendor ID [0x1fc9], Product ID [0x5110], Addr [I2C0 0x50]
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default
environment
[*]-Video Link 0imx8m_hdmi_probe
(1280 x 720)
[0] display-controller@32e00000, video
[1] hdmi@32c00000, display
In: serial
Out: serial
Err: serial
BuildInfo:
- ATF b0a00f2
- U-Boot 2020.04-5.4.24-2.1.0+g4979a99
switch to partitions #0, OK
mmc0(part 0) is current device
flash target is MMC:0
Net:
Warning: ethernet@30be0000 using MAC address from ROM
eth0: ethernet@30be0000
Fastboot: Normal
Normal Boot
Hit any key to stop autoboot: 0
u-boot=> run jh_mmcboot
28021248 bytes read in 190 ms (140.6 MiB/s)
Booting from mmc ...
44482 bytes read in 9 ms (4.7 MiB/s)
## Flattened Device Tree blob at 43000000
Booting using the fdt blob at 0x43000000
Using Device Tree in place at 0000000043000000, end 000000004300ddc1
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 5.4.24-2.1.0+gbabac00 (oe-user@oe-host) (gcc
version 9.2.0 (GCC)) #1 SMP PREEMPT Tue Jul 28 08:36:15 UTC 2020
[ 0.000000] Machine model: NXP i.MX8MQ EVK
[ 0.000000] efi: Getting EFI parameters from FDT:
[ 0.000000] efi: UEFI not found.
[ 0.000000] Reserved memory: created CMA memory pool at
0x0000000044000000, size 960 MiB
[ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id
shared-dma-pool
[ 0.000000] NUMA: No NUMA configuration found
[ 0.000000] NUMA: Faking a node at [mem
0x0000000040000000-0x00000000bfafffff]
[ 0.000000] NUMA: NODE_DATA [mem 0xbf6d0500-0xbf6d1fff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000040000000-0x00000000bfafffff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x00000000b7ffffff]
[ 0.000000] node 0: [mem 0x00000000b8400000-0x00000000bfafffff]
[ 0.000000] Zeroed struct page in unavailable ranges: 256 pages
[ 0.000000] Initmem setup node 0 [mem
0x0000000040000000-0x00000000bfafffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS migration not required
[ 0.000000] psci: SMC Calling Convention v1.1
[ 0.000000] percpu: Embedded 24 pages/cpu s58904 r8192 d31208 u98304
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: ARM erratum 845719
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] Speculative Store Bypass Disable mitigation not required
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 513812
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: clk_ignore_unused
console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait rw
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152
bytes, linear)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576
bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 1035932K/2087936K available (16444K kernel code,
1444K rwdata, 6472K rodata, 2944K init, 1017K bss, 68964K reserved, 983040K
cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to
nr_cpu_ids=4.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is
25 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 128 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] GICv3: 16 PPIs implemented
[ 0.000000] GICv3: no VLPI support, no direct LPI support
[ 0.000000] GICv3: CPU0: found redistributor 0 region
0:0x0000000038880000
[ 0.000000] ITS: No ITS available, not enabling LPIs
[ 0.000000] random: get_random_bytes called from
start_kernel+0x2b8/0x44c with crng_init=0
[ 0.000000] arch_timer: cp15 timer(s) running at 8.33MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff
max_cycles: 0x1ec0311ec, max_idle_ns: 440795202152 ns
[ 0.000003] sched_clock: 56 bits at 8MHz, resolution 120ns, wraps every
2199023255541ns
[ 0.000495] Console: colour dummy device 80x25
[ 0.000563] Calibrating delay loop (skipped), value calculated using
timer frequency.. 16.66 BogoMIPS (lpj=33333)
[ 0.000572] pid_max: default: 32768 minimum: 301
[ 0.000656] LSM: Security Framework initializing
[ 0.000722] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes,
linear)
[ 0.000737] Mountpoint-cache hash table entries: 4096 (order: 3, 32768
bytes, linear)
[ 0.023982] ASID allocator initialised with 32768 entries
[ 0.031985] rcu: Hierarchical SRCU implementation.
[ 0.040943] EFI services will not be available.
[ 0.048015] smp: Bringing up secondary CPUs ...
[ 0.080185] Detected VIPT I-cache on CPU1
[ 0.080212] GICv3: CPU1: found redistributor 1 region
0:0x00000000388a0000
[ 0.080237] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.112213] Detected VIPT I-cache on CPU2
[ 0.112229] GICv3: CPU2: found redistributor 2 region
0:0x00000000388c0000
[ 0.112246] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.144271] Detected VIPT I-cache on CPU3
[ 0.144286] GICv3: CPU3: found redistributor 3 region
0:0x00000000388e0000
[ 0.144305] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.144374] smp: Brought up 1 node, 4 CPUs
[ 0.144395] SMP: Total of 4 processors activated.
[ 0.144403] CPU features: detected: 32-bit EL0 Support
[ 0.144411] CPU features: detected: CRC32 instructions
[ 0.153040] CPU: All CPU(s) started at EL2
[ 0.153065] alternatives: patching kernel code
[ 0.154645] devtmpfs: initialized
[ 0.161855] clocksource: jiffies: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.161873] futex hash table entries: 1024 (order: 4, 65536 bytes,
linear)
[ 0.190302] pinctrl core: initialized pinctrl subsystem
[ 0.191100] DMI not present or invalid.
[ 0.191380] NET: Registered protocol family 16
[ 0.199413] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.199428] audit: initializing netlink subsys (disabled)
[ 0.199558] audit: type=2000 audit(0.196:1): state=initialized
audit_enabled=0 res=1
[ 0.200436] cpuidle: using governor menu
[ 0.200972] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.201927] Serial: AMBA PL011 UART driver
[ 0.202007] imx mu driver is registered.
[ 0.202033] imx rpmsg driver is registered.
[ 0.206078] imx8mq-pinctrl 30330000.iomuxc: initialized IMX pinctrl
driver
[ 0.233181] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.233192] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[ 0.233200] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.233209] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[ 0.235096] cryptd: max_cpu_qlen set to 1000
[ 0.241165] ACPI: Interpreter disabled.
[ 0.242067] iommu: Default domain type: Translated
[ 0.242209] vgaarb: loaded
[ 0.242552] SCSI subsystem initialized
[ 0.242922] usbcore: registered new interface driver usbfs
[ 0.242962] usbcore: registered new interface driver hub
[ 0.243026] usbcore: registered new device driver usb
[ 0.244115] mc: Linux media interface: v0.10
[ 0.244146] videodev: Linux video capture interface: v2.00
[ 0.244224] pps_core: LinuxPPS API ver. 1 registered
[ 0.244231] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo
Giometti <[email protected]>
[ 0.244247] PTP clock support registered
[ 0.244396] EDAC MC: Ver: 3.0.0
[ 0.245234] No BMan portals available!
[ 0.245524] QMan: Allocated lookup table at (____ptrval____), entry
count 65537
[ 0.245847] No QMan portals available!
[ 0.246332] No USDPAA memory, no 'fsl,usdpaa-mem' in device-tree
[ 0.246721] FPGA manager framework
[ 0.246818] Advanced Linux Sound Architecture Driver Initialized.
[ 0.247234] Bluetooth: Core ver 2.22
[ 0.247261] NET: Registered protocol family 31
[ 0.247268] Bluetooth: HCI device and connection manager initialized
[ 0.247280] Bluetooth: HCI socket layer initialized
[ 0.247288] Bluetooth: L2CAP socket layer initialized
[ 0.247302] Bluetooth: SCO socket layer initialized
[ 0.248043] clocksource: Switched to clocksource arch_sys_counter
[ 0.248186] VFS: Disk quotas dquot_6.6.0
[ 0.248244] VFS: Dquot-cache hash table entries: 512 (order 0, 4096
bytes)
[ 0.248438] pnp: PnP ACPI: disabled
[ 0.254681] thermal_sys: Registered thermal governor 'step_wise'
[ 0.254683] thermal_sys: Registered thermal governor 'power_allocator'
[ 0.254977] NET: Registered protocol family 2
[ 0.255332] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2,
16384 bytes, linear)
[ 0.255369] TCP established hash table entries: 16384 (order: 5, 131072
bytes, linear)
[ 0.255500] TCP bind hash table entries: 16384 (order: 6, 262144 bytes,
linear)
[ 0.255747] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.255827] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.255879] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes,
linear)
[ 0.256023] NET: Registered protocol family 1
[ 0.256465] RPC: Registered named UNIX socket transport module.
[ 0.256471] RPC: Registered udp transport module.
[ 0.256476] RPC: Registered tcp transport module.
[ 0.256482] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.256841] PCI: CLS 0 bytes, default 64
[ 0.257582] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7
counters available
[ 0.257955] kvm [1]: IPA Size Limit: 40bits
[ 0.259128] kvm [1]: vgic-v2@31020000
[ 0.259149] kvm [1]: GIC system register CPU interface enabled
[ 0.259216] kvm [1]: vgic interrupt IRQ1
[ 0.259322] kvm [1]: Hyp mode initialized successfully
[ 0.265168] Initialise system trusted keyrings
[ 0.265266] workingset: timestamp_bits=44 max_order=19 bucket_order=0
[ 0.272198] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.272898] NFS: Registering the id_resolver key type
[ 0.272917] Key type id_resolver registered
[ 0.272923] Key type id_legacy registered
[ 0.272935] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.272956] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.273341] 9p: Installing v9fs 9p2000 file system support
[ 0.288879] Key type asymmetric registered
[ 0.288886] Asymmetric key parser 'x509' registered
[ 0.288920] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 244)
[ 0.288929] io scheduler mq-deadline registered
[ 0.288936] io scheduler kyber registered
[ 0.294229] EINJ: ACPI disabled.
[ 0.302727] imx-sdma 302c0000.sdma: Direct firmware load for
imx/sdma/sdma-imx7d.bin failed with error -2
[ 0.302741] imx-sdma 302c0000.sdma: Falling back to sysfs fallback for:
imx/sdma/sdma-imx7d.bin
[ 0.307933] mxs-dma 33000000.dma-apbh: initialized
[ 0.311494] Bus freq driver module loaded
[ 0.316331] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.318483] 30860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 30,
base_baud = 1562500) is a IMX
[ 1.284569] printk: console [ttymxc0] enabled
[ 1.289451] 30880000.serial: ttymxc2 at MMIO 0x30880000 (irq = 31,
base_baud = 5000000) is a IMX
[ 1.307376] imx-dcss 32e00000.display-controller: ctxld: can't get irq
number
[ 1.314603] imx-dcss 32e00000.display-controller: submodules
initialization failed
[ 1.322204] imx-dcss 32e00000.display-controller: master bind failed:
-517
[ 1.339930] loop: module loaded
[ 1.345404] imx ahci driver is registered.
[ 1.352453] spi-nor spi3.0: n25q256a (32768 Kbytes)
[ 1.362522] libphy: Fixed MDIO Bus: probed
[ 1.367503] tun: Universal TUN/TAP device driver, 1.6
[ 1.373322] thunder_xcv, ver 1.0
[ 1.376602] thunder_bgx, ver 1.0
[ 1.379874] nicpf, ver 1.0
[ 1.383349] pps pps0: new PPS source ptp0
[ 1.393265] libphy: fec_enet_mii_bus: probed
[ 1.398699] fec 30be0000.ethernet eth0: registered PHC device 0
[ 1.405311] Freescale FM module, FMD API version 21.1.0
[ 1.410829] Freescale FM Ports module
[ 1.414502] fsl_mac: fsl_mac: FSL FMan MAC API based driver
[ 1.420251] fsl_dpa: FSL DPAA Ethernet driver
[ 1.424736] fsl_advanced: FSL DPAA Advanced drivers:
[ 1.429710] fsl_proxy: FSL DPAA Proxy initialization driver
[ 1.435400] fsl_oh: FSL FMan Offline Parsing port driver
[ 1.441694] hclge is initializing
[ 1.445024] hns3: Hisilicon Ethernet Network Driver for Hip08 Family -
version
[ 1.452256] hns3: Copyright (c) 2017 Huawei Corporation.
[ 1.457620] e1000: Intel(R) PRO/1000 Network Driver - version
7.3.21-k8-NAPI
[ 1.464675] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 1.470463] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[ 1.476301] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 1.482264] igb: Intel(R) Gigabit Ethernet Network Driver - version
5.6.0-k
[ 1.489238] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 1.494858] igbvf: Intel(R) Gigabit Virtual Function Network Driver -
version 2.4.0-k
[ 1.502695] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[ 1.508792] sky2: driver version 1.30
[ 1.513478] VFIO - User Level meta-driver version: 0.3
[ 1.521163] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.527703] ehci-pci: EHCI PCI platform driver
[ 1.532212] ehci-platform: EHCI generic platform driver
[ 1.537640] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.543840] ohci-pci: OHCI PCI platform driver
[ 1.548325] ohci-platform: OHCI generic platform driver
[ 1.554171] usbcore: registered new interface driver usb-storage
[ 1.560256] usbcore: registered new interface driver usbserial_generic
[ 1.566814] usbserial: USB Serial support registered for generic
[ 1.572853] usbcore: registered new interface driver ftdi_sio
[ 1.578624] usbserial: USB Serial support registered for FTDI USB Serial
Device
[ 1.585969] usbcore: registered new interface driver usb_serial_simple
[ 1.592523] usbserial: USB Serial support registered for carelink
[ 1.598644] usbserial: USB Serial support registered for zio
[ 1.604330] usbserial: USB Serial support registered for funsoft
[ 1.610360] usbserial: USB Serial support registered for flashloader
[ 1.616739] usbserial: USB Serial support registered for google
[ 1.622684] usbserial: USB Serial support registered for libtransistor
[ 1.629236] usbserial: USB Serial support registered for vivopay
[ 1.635268] usbserial: USB Serial support registered for moto_modem
[ 1.641562] usbserial: USB Serial support registered for motorola_tetra
[ 1.648209] usbserial: USB Serial support registered for novatel_gps
[ 1.654590] usbserial: USB Serial support registered for hp4x
[ 1.660367] usbserial: USB Serial support registered for suunto
[ 1.666312] usbserial: USB Serial support registered for siemens_mpi
[ 1.675516] input: 30370000.snvs:snvs-powerkey as
/devices/platform/soc@0/soc@0:bus@30000000/30370000.snvs/30370000.snvs:snvs-powerkey/input/input0
[ 1.690752] snvs_rtc 30370000.snvs:snvs-rtc-lp: registered as rtc0
[ 1.697045] i2c /dev entries driver
[ 1.701173] mxc-mipi-csi2_yav 30a70000.mipi_csi1: mipi_csi2_probe
[ 1.707327] mxc-mipi-csi2_yav 30a70000.mipi_csi: Remote device at
endpoint@0 XXX found
[ 1.715266] mxc-mipi-csi2_yav 30a70000.mipi_csi1: lanes: 2, name:
mxc-mipi-csi2.0
[ 1.722969] mxc-mipi-csi2_yav 30b60000.mipi_csi2: mipi_csi2_probe
[ 1.729120] mxc-mipi-csi2_yav 30b60000.mipi_csi: Remote device at
endpoint@0 XXX found
[ 1.737059] mxc-mipi-csi2_yav 30b60000.mipi_csi2: lanes: 2, name:
mxc-mipi-csi2.1
[ 1.744795] mx6s-csi 30a90000.csi1_bridge: initialising
[ 1.750232] CSI: Registered sensor subdevice: mxc-mipi-csi2.0
[ 1.756065] mx6s-csi 30b80000.csi2_bridge: initialising
[ 1.761479] CSI: Registered sensor subdevice: mxc-mipi-csi2.1
[ 1.769869] imx2-wdt 30280000.watchdog: timeout 60 sec (nowayout=0)
[ 1.776453] Bluetooth: HCI UART driver ver 2.3
[ 1.780914] Bluetooth: HCI UART protocol H4 registered
[ 1.786066] Bluetooth: HCI UART protocol BCSP registered
[ 1.791407] Bluetooth: HCI UART protocol LL registered
[ 1.796557] Bluetooth: HCI UART protocol ATH3K registered
[ 1.801988] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 1.808351] Bluetooth: HCI UART protocol Broadcom registered
[ 1.814040] Bluetooth: HCI UART protocol QCA registered
[ 1.821640] sdhci: Secure Digital Host Controller Interface driver
[ 1.827831] sdhci: Copyright(c) Pierre Ossman
[ 1.832406] Synopsys Designware Multimedia Card Interface Driver
[ 1.839083] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.847135] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.854303] caam 30900000.crypto: device ID = 0x0a16040100000000 (Era 9)
[ 1.861021] caam 30900000.crypto: job rings = 2, qi = 0
[ 1.885558] caam algorithms registered in /proc/crypto
[ 1.892931] caam 30900000.crypto: caam pkc algorithms registered in
/proc/crypto
[ 1.902488] caam_jr 30901000.jr: registering rng-caam
[ 1.916809] caam-snvs 30370000.caam-snvs: can't get snvs clock
[ 1.922688] caam-snvs 30370000.caam-snvs: violation handlers armed -
non-secure state
[ 1.931206] usbcore: registered new interface driver usbhid
[ 1.936838] usbhid: USB HID core driver
[ 1.942169] No fsl,qman node
[ 1.945066] Freescale USDPAA process driver
[ 1.949257] fsl-usdpaa: no region found
[ 1.953100] Freescale USDPAA process IRQ driver
[ 1.961015] optee: probing for conduit method from DT.
[ 1.966195] optee: revision 3.7 (7a49776d)
[ 1.966406] optee: dynamic shared memory is enabled
[ 1.975618] optee: initialized driver
[ 1.982779] wm8524-codec audio-codec: Failed to get mute line: -517
[ 2.059611] imx-spdif sound-spdif: snd-soc-dummy-dai <-> 30810000.spdif
mapping ok
[ 2.067221] imx-spdif sound-spdif: ASoC: no DMI vendor name!
[ 2.075323] imx-spdif sound-hdmi-arc: snd-soc-dummy-dai <->
308a0000.spdif mapping ok
[ 2.083184] imx-spdif sound-hdmi-arc: ASoC: no DMI vendor name!
[ 2.090242] imx-ak4458 sound-ak4458: ASoC: failed to init link ak4458:
-517
[ 2.097228] imx-ak4458 sound-ak4458: snd_soc_register_card failed (-517)
[ 2.104197] imx-ak5558 sound-ak5558: ASoC: failed to init link ak5558:
-517
[ 2.111174] imx-ak5558 sound-ak5558: snd_soc_register_card failed (-517)
[ 2.118525] imx-cdnhdmi sound-hdmi: ASoC: failed to init link imx8 hdmi:
-517
[ 2.125679] imx-cdnhdmi sound-hdmi: snd_soc_register_card failed (-517)
[ 2.132548] pktgen: Packet Generator for packet performance testing.
Version: 2.75
[ 2.140668] NET: Registered protocol family 26
[ 2.145780] NET: Registered protocol family 10
[ 2.150963] Segment Routing with IPv6
[ 2.154698] NET: Registered protocol family 17
[ 2.159246] Bluetooth: RFCOMM TTY layer initialized
[ 2.164141] Bluetooth: RFCOMM socket layer initialized
[ 2.169313] Bluetooth: RFCOMM ver 1.11
[ 2.173079] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 2.178400] Bluetooth: BNEP filters: protocol multicast
[ 2.183641] Bluetooth: BNEP socket layer initialized
[ 2.188614] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 2.194546] Bluetooth: HIDP socket layer initialized
[ 2.199551] 8021q: 802.1Q VLAN Support v1.8
[ 2.203760] lib80211: common routines for IEEE802.11 drivers
[ 2.209538] 9pnet: Installing 9P2000 support
[ 2.213846] tsn generic netlink module v1 init...
[ 2.218616] Key type dns_resolver registered
[ 2.223334] registered taskstats version 1
[ 2.227450] Loading compiled-in X.509 certificates
[ 2.252874] GPIO line 157 (wl-reg-on) hogged as output/high
[ 2.260890] ov5640_mipi 0-003c: No sensor reset pin available
[ 2.266679] ov5640_mipi 0-003c: 0-003c supply DOVDD not found, using
dummy regulator
[ 2.274488] ov5640_mipi 0-003c: 0-003c supply DVDD not found, using
dummy regulator
[ 2.282216] ov5640_mipi 0-003c: 0-003c supply AVDD not found, using
dummy regulator
[ 2.300363] ov5640_mipi 0-003c: Read reg error: reg=300a
[ 2.305688] ov5640_mipi 0-003c: Camera is not found
[ 2.312187] pfuze100-regulator 0-0008: Full layer: 2, Metal layer: 1
[ 2.319167] pfuze100-regulator 0-0008: FAB: 0, FIN: 0
[ 2.324243] pfuze100-regulator 0-0008: pfuze100 found.
[ 2.346402] i2c i2c-0: IMX I2C adapter registered
[ 2.351961] ov5640_mipi 1-003c: No sensor reset pin available
[ 2.357752] ov5640_mipi 1-003c: 1-003c supply DOVDD not found, using
dummy regulator
[ 2.365561] ov5640_mipi 1-003c: 1-003c supply DVDD not found, using
dummy regulator
[ 2.373270] ov5640_mipi 1-003c: 1-003c supply AVDD not found, using
dummy regulator
[ 2.425516] random: fast init done
[ 3.552073] mxc-mipi-csi2_yav 30a70000.mipi_csi: Registered sensor
subdevice: ov5640_mipi 1-003c
[ 3.562103] ov5640_mipi 1-003c: Camera is found
[ 3.566692] i2c i2c-1: IMX I2C adapter registered
[ 3.572225] ak4458 2-0010: 2-0010 supply DVDD not found, using dummy
regulator
[ 3.579503] ak4458 2-0010: 2-0010 supply AVDD not found, using dummy
regulator
[ 3.587128] ak4458 2-0012: 2-0012 supply DVDD not found, using dummy
regulator
[ 3.594428] ak4458 2-0012: 2-0012 supply AVDD not found, using dummy
regulator
[ 3.602034] ak5558 2-0013: 2-0013 supply DVDD not found, using dummy
regulator
[ 3.609309] ak5558 2-0013: 2-0013 supply AVDD not found, using dummy
regulator
[ 3.616942] ak4458 2-0011: 2-0011 supply DVDD not found, using dummy
regulator
[ 3.624222] ak4458 2-0011: 2-0011 supply AVDD not found, using dummy
regulator
[ 3.631567] i2c i2c-2: IMX I2C adapter registered
[ 3.636791] imx8mq-usb-phy 381f0040.usb-phy: 381f0040.usb-phy supply
vbus not found, using dummy regulator
[ 3.646740] imx8mq-usb-phy 382f0040.usb-phy: 382f0040.usb-phy supply
vbus not found, using dummy regulator
[ 3.658518] imx6q-pcie 33c00000.pcie: couldn't get pcie-phy
[ 3.664266] imx6q-pcie 33c00000.pcie: 33c00000.pcie supply epdev_on not
found, using dummy regulator
[ 3.664780] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 3.673673] imx6q-pcie 33c00000.pcie: host bridge /soc@0/pcie@33c00000
ranges:
[ 3.680040] [drm] No driver support for vblank timestamp query.
[ 3.680581] cdns-mhdp-imx 32c00000.hdmi: lane-mapping 0xe4
[ 3.687274] imx6q-pcie 33c00000.pcie: No bus range found for
/soc@0/pcie@33c00000, using [bus 00-ff]
[ 3.687304] imx6q-pcie 33c00000.pcie: IO 0x27f80000..0x27f8ffff ->
0x00000000
[ 3.695218] imx-dcss 32e00000.display-controller: bound 32c00000.hdmi
(ops cdns_mhdp_imx_ops)
[ 3.698706] imx6q-pcie 33c00000.pcie: MEM 0x20000000..0x27efffff ->
0x20000000
[ 3.708361] [drm] Initialized imx-dcss 1.0.0 20190917 for
32e00000.display-controller on minor 0
[ 3.765728] cdns-mhdp-imx 32c00000.hdmi: 0,ff,ff,ff,ff,ff,ff,0
[ 3.803626] cdns-mhdp-imx 32c00000.hdmi: 0,ff,ff,ff,ff,ff,ff,0
[ 3.804589] [drm] Mode: 1920x1080p148500
[ 3.820087] imx6q-pcie 33c00000.pcie: PCIe PLL locked after 0 us.
[ 3.832073] [drm] Pixel clock: 148500 KHz, character clock: 222750, bpc
is 12-bit.
[ 3.832079] [drm] VCO frequency is 4455000 KHz
[ 3.909255] [drm] Sink Not Support SCDC
[ 3.910487] [drm] No vendor infoframe
[ 4.006715] Console: switching to colour frame buffer device 240x67
[ 4.080055] imx-dcss 32e00000.display-controller: fb0: imx-dcssdrmfb
frame buffer device
[ 4.089306] OF: graph: no port node found in /soc@0/usb-phy@381f0040
[ 4.096786] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 4.102300] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned
bus number 1
[ 4.110086] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe6c hci version
0x110 quirks 0x0000000001010010
[ 4.119550] xhci-hcd xhci-hcd.1.auto: irq 53, io mem 0x38200000
[ 4.126219] hub 1-0:1.0: USB hub found
[ 4.130021] hub 1-0:1.0: 1 port detected
[ 4.134215] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 4.139723] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned
bus number 2
[ 4.147415] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 4.154014] usb usb2: We don't know the algorithms for LPM for this
host, disabling LPM.
[ 4.162561] hub 2-0:1.0: USB hub found
[ 4.166346] hub 2-0:1.0: 1 port detected
[ 4.171452] imx-cpufreq-dt imx-cpufreq-dt: cpu speed grade 3 mkt segment
0 supported-hw 0x8 0x1
[ 4.182246] sdhci-esdhc-imx 30b50000.mmc: Got CD GPIO
[ 4.216897] mmc1: SDHCI controller on 30b50000.mmc [30b50000.mmc] using
ADMA
[ 4.226780] galcore: clk_get 2d core clock failed, disable 2d/vg!
[ 4.233248] Galcore version 6.4.0.234062
[ 4.347584] hantrodec: module inserted. Major = 236
[ 4.354696] debugfs: Directory '308b0000.sai' with parent 'wm8524-audio'
already present!
[ 4.363020] asoc-simple-card sound-wm8524: wm8524-hifi <-> 308b0000.sai
mapping ok
[ 4.370644] asoc-simple-card sound-wm8524: ASoC: no DMI vendor name!
[ 4.382398] ak4458 2-0010: ASoC: failed to probe component -6
[ 4.388215] imx-ak4458 sound-ak4458: ASoC: failed to instantiate card -6
[ 4.395010] imx-ak4458 sound-ak4458: snd_soc_register_card failed (-6)
[ 4.402517] ak5558 2-0013: ASoC: failed to probe component -6
[ 4.408350] imx-ak5558 sound-ak5558: ASoC: failed to instantiate card -6
[ 4.415140] imx-ak5558 sound-ak5558: snd_soc_register_card failed (-6)
[ 4.422590] debugfs: Directory '30050000.sai' with parent
'imx-audio-hdmi' already present!
[ 4.431068] imx-cdnhdmi sound-hdmi: i2s-hifi <-> 30050000.sai mapping ok
[ 4.437846] imx-cdnhdmi sound-hdmi: ASoC: no DMI vendor name!
[ 4.443694] debugfs: File 'Capture' in directory 'dapm' already present!
[ 4.458915] mmc1: host does not support reading read-only switch,
assuming write-enable
[ 4.468073] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 4.471829] imx6q-pcie 33800000.pcie: couldn't get pcie-phy
[ 4.480204] snvs_rtc 30370000.snvs:snvs-rtc-lp: setting system clock to
1970-01-01T00:00:02 UTC (2)
[ 4.480280] imx6q-pcie 33800000.pcie: 33800000.pcie supply epdev_on not
found, using dummy regulator
[ 4.489624] cfg80211: Loading compiled-in X.509 certificates for
regulatory database
[ 4.498627] imx6q-pcie 33800000.pcie: host bridge /soc@0/pcie@33800000
ranges:
[ 4.508221] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 4.513396] imx6q-pcie 33800000.pcie: IO 0x1ff80000..0x1ff8ffff ->
0x00000000
[ 4.519977] platform regulatory.0: Direct firmware load for
regulatory.db failed with error -2
[ 4.527318] imx6q-pcie 33800000.pcie: MEM 0x18000000..0x1fefffff ->
0x18000000
[ 4.535919] clk: Not disabling unused clocks
[ 4.547613] platform regulatory.0: Falling back to sysfs fallback for:
regulatory.db
[ 4.555454] ALSA device list:
[ 4.558454] #0: imx-spdif
[ 4.561258] #1: imx-hdmi-arc
[ 4.564320] #2: wm8524-audio
[ 4.567377] #3: imx-audio-hdmi
[ 4.570139] hub 1-1:1.0: USB hub found
[ 4.574405] hub 1-1:1.0: 4 ports detected
[ 4.580058] mmc1: new ultra high speed DDR50 SDHC card at address aaaa
[ 4.587027] mmcblk1: mmc1:aaaa SS32G 29.7 GiB
[ 4.600114] mmcblk1: p1 p2
[ 4.648111] imx6q-pcie 33800000.pcie: PCIe PLL locked after 0 us.
[ 4.752076] imx6q-pcie 33800000.pcie: Link up
[ 4.756448] imx6q-pcie 33800000.pcie: Link up
[ 4.760824] imx6q-pcie 33800000.pcie: Link up, Gen1
[ 4.765935] imx6q-pcie 33800000.pcie: PCI host bridge to bus 0000:00
[ 4.772298] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 4.777805] pci_bus 0000:00: root bus resource [io 0x10000-0x1ffff]
(bus address [0x0000-0xffff])
[ 4.786779] pci_bus 0000:00: root bus resource [mem
0x18000000-0x1fefffff]
[ 4.793679] pci 0000:00:00.0: [16c3:abcd] type 01 class 0x060400
[ 4.799718] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
[ 4.805999] pci 0000:00:00.0: reg 0x38: [mem 0x00000000-0x0000ffff pref]
[ 4.812752] pci 0000:00:00.0: supports D1
[ 4.816767] pci 0000:00:00.0: PME# supported from D0 D1 D3hot D3cold
[ 4.825074] pci 0000:01:00.0: [168c:003e] type 00 class 0x028000
[ 4.827406] imx6q-pcie 33c00000.pcie: Phy link never came up
[ 4.831176] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 4.836797] imx6q-pcie 33c00000.pcie: failed to initialize host
[ 4.843880] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 4.849477] imx6q-pcie 33c00000.pcie: unable to add pcie port.
[ 4.865657] pci 0000:00:00.0: BAR 14: assigned [mem
0x18000000-0x181fffff]
[ 4.872543] pci 0000:00:00.0: BAR 0: assigned [mem 0x18200000-0x182fffff]
[ 4.879341] pci 0000:00:00.0: BAR 6: assigned [mem 0x18300000-0x1830ffff
pref]
[ 4.886574] pci 0000:01:00.0: BAR 0: assigned [mem 0x18000000-0x181fffff
64bit]
[ 4.893914] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 4.899148] pci 0000:00:00.0: bridge window [mem 0x18000000-0x181fffff]
[ 4.906263] pcieport 0000:00:00.0: PME: Signaling with IRQ 231
[ 4.912315] pcieport 0000:00:00.0: AER: enabled with IRQ 231
[ 4.918292] Waiting for root device /dev/mmcblk0p2...
[ 4.968080] usb 1-1.2: new high-speed USB device number 3 using xhci-hcd
[ 5.248053] usb 1-1.4: new low-speed USB device number 4 using xhci-hcd
[ 5.532467] input: PixArt USB Optical Mouse as
/devices/platform/soc@0/38200000.usb/xhci-hcd.1.auto/usb1/1-1/1-1.4/1-1.4:1.0/0003:093A:2510.0001/input/input1
[ 5.546652] hid-generic 0003:093A:2510.0001: input: USB HID v1.11 Mouse
[PixArt USB Optical Mouse] on usb-xhci-hcd.1.auto-1.4/input0
[ 35.808082] vdd_arm: disabling
[ 35.811158] VGEN1: disabling
[ 35.814747] VGEN6: disabling
[ 60.384106] imx-sdma 30bd0000.sdma: external firmware not found, using
ROM firmware
[ 60.384226] imx-sdma 302c0000.sdma: Direct firmware load for
imx/sdma/sdma-imx7d.bin failed with error -2
[ 60.401363] imx-sdma 302c0000.sdma: Falling back to sysfs fallback for:
imx/sdma/sdma-imx7d.bin
[ 61.544094] random: crng init done
[ 66.528146] cfg80211: failed to load regulatory.db
[ 121.824100] imx-sdma 302c0000.sdma: external firmware not found, using
ROM firmware
On Thursday, August 6, 2020 at 6:52:17 AM UTC+5:30, Peng Fan wrote:
>
>
>
> Vipul Suneja <[email protected] <javascript:>> 于2020年8月5日周三 下午4:48写道：
>
>>
>> Target: imx8mq evk
>> bsp: 5.4.24
>>
>> Created & started linux cell. Does it maintain separate rootfs? How
>> to run a binary in this 2nd linux (in dedicated CPU)? I didn't found
>> initrd.img, didn't include in the below given command.
>>
>> * jailhouse cell linux
>> /usr/share/jailhouse/cells/imx8mq-linux-demo.cell
>> /run/media/mmcblk1p1/Image -d /run/media/mmcblk1p1/imx8mq-evk-inmate.dtb -c
>> "clk_ignore_unused console=ttymxc0,115200
>> earlycon=ec_imx6q,0x30860000,115200 root=/dev/mmcblk1p2 rootwait rw"*
>>
>
> Change the root to /dev/mmcblk2p2 according to your boot log. The 2nd
> linux take the emmc on board as the rootfs storage media.
> So you need first use uuu to burn the sdcard image to the emmc device on
> board. And the 2nd linux will use the other uart as normal console,
> it take the 1st linux uart as early console.
>
> Regards,
> Peng.
>
>>
>>
>> Below are logs:
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>> *Adding virtual PCI device 00:00.0 to cell "linux-inmate-demo"Shared
>> memory connection established, peer cells: "imx8mq"Adding virtual PCI
>> device 00:01.0 to cell "linux-inmate-demo"Shared memory connection
>> established, peer cells: "imx8mq"Created cell "linux-inmate-demo"Page pool
>> usage after cell creation: mem 80/992, remap 144/131072[ 1021.954940]
>> Created Jailhouse cell "linux-inmate-demo"Cell "linux-inmate-demo" can be
>> loadedStarted cell "linux-inmate-demo"[ 0.000000] Booting Linux on
>> physical CPU 0x0000000002 [0x410fd034][ 0.000000] Linux version
>> 5.4.24-2.1.0+gbabac00 (oe-user@oe-host) (gcc version 9.2.0 (GCC)) #1 SMP
>> PREEMPT Tue Jul 28 08:36:15 UTC 2020[ 0.000000] Machine model: Freescale
>> i.MX8MQ EVK[ 0.000000] earlycon: ec_imx6q0 at MMIO 0x0000000030860000
>> (options '115200')[ 0.000000] printk: bootconsole [ec_imx6q0]
>> enabled[ 0.000000] efi: Getting EFI parameters from FDT:[ 0.000000]
>> efi: UEFI not found.[ 0.000000] cma: Reserved 320 MiB at
>> 0x00000000e8000000[ 0.000000] NUMA: No NUMA configuration found[
>> 0.000000] NUMA: Faking a node at [mem
>> 0x00000000c0000000-0x00000000fdbfffff][ 0.000000] NUMA: NODE_DATA [mem
>> 0xfda0d500-0xfda0efff][ 0.000000] Zone ranges:[ 0.000000] DMA32
>> [mem 0x00000000c0000000-0x00000000fdbfffff][ 0.000000] Normal
>> empty[ 0.000000] Movable zone start for each node[ 0.000000] Early
>> memory node ranges[ 0.000000] node 0: [mem
>> 0x00000000c0000000-0x00000000fdbfffff][ 0.000000] Initmem setup node 0
>> [mem 0x00000000c0000000-0x00000000fdbfffff][ 0.000000] psci: probing for
>> conduit method from DT.[ 0.000000] psci: PSCIv1.1 detected in
>> firmware.[ 0.000000] psci: Using standard PSCI v0.2 function IDs[
>> 0.000000] psci: MIGRATE_INFO_TYPE not supported.[ 0.000000] psci: SMC
>> Calling Convention v1.1[ 0.000000] percpu: Embedded 24 pages/cpu s58904
>> r8192 d31208 u98304[ 0.000000] Detected VIPT I-cache on CPU0[
>> 0.000000] CPU features: detected: ARM erratum 845719[ 0.000000] CPU
>> features: detected: GIC system register CPU interface[ 0.000000] Built 1
>> zonelists, mobility grouping on. Total pages: 248976[ 0.000000] Policy
>> zone: DMA32[ 0.000000] Kernel command line: clk_ignore_unused
>> console=ttymxc0,115200 earlycon=ec_imx6q,0x30860000,115200
>> root=/dev/mmcblk1p2 rootwait rw[ 0.000000] Dentry cache hash table
>> entries: 131072 (order: 8, 1048576 bytes, linear)[ 0.000000] Inode-cache
>> hash table entries: 65536 (order: 7, 524288 bytes, linear)[ 0.000000]
>> mem auto-init: stack:off, heap alloc:off, heap free:off[ 0.000000]
>> Memory: 635512K/1011712K available (16444K kernel code, 1444K rwdata, 6472K
>> rodata, 2944K init, 1017K bss, 48520K reserved, 327680K cma-reserved)[
>> 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1[
>> 0.000000] rcu: Preemptible hierarchical RCU implementation.[ 0.000000]
>> rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2.[
>> 0.000000] Tasks RCU enabled.[ 0.000000] rcu: RCU calculated value of
>> scheduler-enlistment delay is 25 jiffies.[ 0.000000] rcu: Adjusting
>> geometry for rcu_fanout_leaf=16, nr_cpu_ids=2[ 0.000000] NR_IRQS: 64,
>> nr_irqs: 64, preallocated irqs: 0[ 0.000000] GICv3: 128 SPIs
>> implemented[ 0.000000] GICv3: 0 Extended SPIs implemented[ 0.000000]
>> GICv3: Distributor has no Range Selector support[ 0.000000] GICv3: 16
>> PPIs implemented[ 0.000000] GICv3: no VLPI support, no direct LPI
>> support[ 0.000000] GICv3: CPU0: found redistributor 2 region
>> 0:0x00000000388c0000[ 0.000000] ITS: No ITS available, not enabling
>> LPIs[ 0.000000] random: get_random_bytes called from
>> start_kernel+0x2b8/0x44c with crng_init=0[ 0.000000] arch_timer: cp15
>> timer(s) running at 8.33MHz (virt).[ 0.000000] clocksource:
>> arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1ec0311ec,
>> max_idle_ns: 440795202152 ns[ 0.000004] sched_clock: 56 bits at 8MHz,
>> resolution 120ns, wraps every 2199023255541ns[ 0.008121] Console: colour
>> dummy device 80x25[ 0.012473] Calibrating delay loop (skipped), value
>> calculated using timer frequency.. 16.66 BogoMIPS (lpj=33333)[ 0.022664]
>> pid_max: default: 32768 minimum: 301[ 0.027337] LSM: Security Framework
>> initializing[ 0.031915] Mount-cache hash table entries: 2048 (order: 2,
>> 16384 bytes, linear)[ 0.039248] Mountpoint-cache hash table entries:
>> 2048 (order: 2, 16384 bytes, linear)[ 0.071135] ASID allocator
>> initialised with 32768 entries[ 0.079137] rcu: Hierarchical SRCU
>> implementation.[ 0.087271] EFI services will not be available.[
>> 0.095177] smp: Bringing up secondary CPUs ...[ 0.127296] Detected VIPT
>> I-cache on CPU1[ 0.127333] GICv3: CPU1: found redistributor 3 region
>> 0:0x00000000388e0000[ 0.127374] CPU1: Booted secondary processor
>> 0x0000000003 [0x410fd034][ 0.127452] smp: Brought up 1 node, 2 CPUs[
>> 0.146060] SMP: Total of 2 processors activated.[ 0.150745] CPU features:
>> detected: 32-bit EL0 Support[ 0.155882] CPU features: detected: CRC32
>> instructions[ 0.171395] CPU: All CPU(s) started at EL1[ 0.172643]
>> alternatives: patching kernel code[ 0.178327] devtmpfs: initialized[
>> 0.182016] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff,
>> max_idle_ns: 7645041785100000 ns[ 0.190093] futex hash table entries:
>> 512 (order: 3, 32768 bytes, linear)[ 0.205814] pinctrl core: initialized
>> pinctrl subsystem[ 0.208766] DMI not present or invalid.[ 0.212295]
>> NET: Registered protocol family 16[ 0.226844] DMA: preallocated 256 KiB
>> pool for atomic allocations[ 0.230091] audit: initializing netlink
>> subsys (disabled)[ 0.235625] audit: type=2000 audit(0.200:1):
>> state=initialized audit_enabled=0 res=1[ 0.243221] cpuidle: using
>> governor menu[ 0.247461] hw-breakpoint: found 6 breakpoint and 4
>> watchpoint registers.[ 0.254239] Serial: AMBA PL011 UART driver[
>> 0.258022] imx mu driver is registered.[ 0.261865] imx rpmsg driver is
>> registered.[ 0.283632] HugeTLB registered 1.00 GiB page size,
>> pre-allocated 0 pages[ 0.287485] HugeTLB registered 32.0 MiB page size,
>> pre-allocated 0 pages[ 0.294161] HugeTLB registered 2.00 MiB page size,
>> pre-allocated 0 pages[ 0.300846] HugeTLB registered 64.0 KiB page size,
>> pre-allocated 0 pages[ 0.309530] cryptd: max_cpu_qlen set to 1000[
>> 0.317166] ACPI: Interpreter disabled.[ 0.318509] iommu: Default domain
>> type: Translated[ 0.323154] vgaarb: loaded[ 0.325989] SCSI subsystem
>> initialized[ 0.329830] usbcore: registered new interface driver
>> usbfs[ 0.334947] usbcore: registered new interface driver hub[
>> 0.340466] usbcore: registered new device driver usb[ 0.345518] mc: Linux
>> media interface: v0.10[ 0.349507] videodev: Linux video capture
>> interface: v2.00[ 0.355017] pps_core: LinuxPPS API ver. 1 registered[
>> 0.359900] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo
>> Giometti <[email protected] <javascript:>>[ 0.369034] PTP clock support
>> registered[ 0.372976] EDAC MC: Ver: 3.0.0[ 0.376456] No BMan portals
>> available![ 0.379991] QMan: Allocated lookup table at (____ptrval____),
>> entry count 65537[ 0.387121] No QMan portals available![ 0.390844] No
>> USDPAA memory, no 'fsl,usdpaa-mem' in device-tree[ 0.397047] FPGA
>> manager framework[ 0.400255] Advanced Linux Sound Architecture Driver
>> Initialized.[ 0.406683] Bluetooth: Core ver 2.22[ 0.409838] NET:
>> Registered protocol family 31[ 0.414246] Bluetooth: HCI device and
>> connection manager initialized[ 0.420580] Bluetooth: HCI socket layer
>> initialized[ 0.425440] Bluetooth: L2CAP socket layer initialized[
>> 0.430494] Bluetooth: SCO socket layer initialized[ 0.435863]
>> clocksource: Switched to clocksource arch_sys_counter[ 0.441553] VFS:
>> Disk quotas dquot_6.6.0[ 0.445367] VFS: Dquot-cache hash table entries:
>> 512 (order 0, 4096 bytes)[ 0.452334] pnp: PnP ACPI: disabled[
>> 0.462170] thermal_sys: Registered thermal governor 'step_wise'[
>> 0.462173] thermal_sys: Registered thermal governor 'power_allocator'[
>> 0.465472] NET: Registered protocol family 2[ 0.476511]
>> tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes,
>> linear)[ 0.484540] TCP established hash table entries: 8192 (order: 4,
>> 65536 bytes, linear)[ 0.492302] TCP bind hash table entries: 8192
>> (order: 5, 131072 bytes, linear)[ 0.499571] TCP: Hash tables configured
>> (established 8192 bind 8192)[ 0.505845] UDP hash table entries: 512
>> (order: 2, 16384 bytes, linear)[ 0.512401] UDP-Lite hash table entries:
>> 512 (order: 2, 16384 bytes, linear)[ 0.519510] NET: Registered protocol
>> family 1[ 0.524157] RPC: Registered named UNIX socket transport
>> module.[ 0.529649] RPC: Registered udp transport module.[ 0.534334]
>> RPC: Registered tcp transport module.[ 0.539023] RPC: Registered tcp
>> NFSv4.1 backchannel transport module.[ 0.545810] PCI: CLS 0 bytes,
>> default 64[ 0.549924] kvm [1]: HYP mode not available[ 0.559322]
>> Initialise system trusted keyrings[ 0.561042] workingset:
>> timestamp_bits=44 max_order=18 bucket_order=0[ 0.574077] squashfs:
>> version 4.0 (2009/01/31) Phillip Lougher[ 0.577766] NFS: Registering the
>> id_resolver key type[ 0.582117] Key type id_resolver registered[
>> 0.586255] Key type id_legacy registered[ 0.590256] nfs4filelayout_init:
>> NFSv4 File Layout Driver Registering...[ 0.596947] jffs2: version 2.2.
>> (NAND) © 2001-2006 Red Hat, Inc.[ 0.603415] 9p: Installing v9fs 9p2000
>> file system support[ 0.623963] Key type asymmetric registered[
>> 0.625197] Asymmetric key parser 'x509' registered[ 0.630097] Block layer
>> SCSI generic (bsg) driver version 0.4 loaded (major 244)[ 0.637464] io
>> scheduler mq-deadline registered[ 0.641963] io scheduler kyber
>> registered[ 0.646985] pci-host-generic bfb00000.pci: host bridge
>> /pci@bfb00000 ranges:[ 0.653010] pci-host-generic bfb00000.pci: MEM
>> 0x10000000..0x1000ffff -> 0x10000000[ 0.660844] pci-host-generic
>> bfb00000.pci: ECAM at [mem 0xbfb00000-0xbfbfffff] for [bus 00][
>> 0.669234] pci-host-generic bfb00000.pci: PCI host bridge to bus 0000:00[
>> 0.675904] pci_bus 0000:00: root bus resource [bus 00][ 0.681117] pci_bus
>> 0000:00: root bus resource [mem 0x10000000-0x1000ffff][ 0.687999] pci
>> 0000:00:00.0: [110a:4106] type 00 class 0xff0000[ 0.693983] pci
>> 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff][ 0.700441] pci
>> 0000:00:01.0: [110a:4106] type 00 class 0xff0001[ 0.706215] pci
>> 0000:00:01.0: reg 0x10: [mem 0x00000000-0x00000fff][ 0.712846] pci
>> 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x10000fff][ 0.719226] pci
>> 0000:00:01.0: BAR 0: assigned [mem 0x10001000-0x10001fff][ 0.730661]
>> EINJ: ACPI disabled.[ 0.731846] Bus freq driver module loaded[
>> 0.738437] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled[
>> 0.743272] 30890000.serial: ttymxc1 at MMIO 0x30890000 (irq = 5, base_baud =
>> 1562500) is a IMX[ 0.758802] loop: module loaded[ 0.760497] imx ahci
>> driver is registered.[ 0.764652] libphy: Fixed MDIO Bus: probed[
>> 0.768138] tun: Universal TUN/TAP device driver, 1.6[ 0.772584]
>> thunder_xcv, ver 1.0[ 0.775525] thunder_bgx, ver 1.0[ 0.778759]
>> nicpf, ver 1.0[ 0.781574] Freescale FM module, FMD API version
>> 21.1.0[ 0.786667] Freescale FM Ports module[ 0.790255] fsl_mac:
>> fsl_mac: FSL FMan MAC API based driver[ 0.795852] fsl_dpa: FSL DPAA
>> Ethernet driver[ 0.800190] fsl_advanced: FSL DPAA Advanced drivers:[
>> 0.805098] fsl_proxy: FSL DPAA Proxy initialization driver[ 0.810691]
>> fsl_oh: FSL FMan Offline Parsing port driver[ 0.816330] hclge is
>> initializing[ 0.819240] hns3: Hisilicon Ethernet Network Driver for
>> Hip08 Family - version[ 0.826457] hns3: Copyright (c) 2017 Huawei
>> Corporation.[ 0.831800] e1000: Intel(R) PRO/1000 Network Driver -
>> version 7.3.21-k8-NAPI[ 0.838777] e1000: Copyright (c) 1999-2006 Intel
>> Corporation.[ 0.844545] e1000e: Intel(R) PRO/1000 Network Driver -
>> 3.2.6-k[ 0.850324] e1000e: Copyright(c) 1999 - 2015 Intel
>> Corporation.[ 0.856268] igb: Intel(R) Gigabit Ethernet Network Driver -
>> version 5.6.0-k[ 0.863169] igb: Copyright (c) 2007-2014 Intel
>> Corporation.[ 0.868770] igbvf: Intel(R) Gigabit Virtual Function Network
>> Driver - version 2.4.0-k[ 0.876539] igbvf: Copyright (c) 2009 - 2012
>> Intel Corporation.[ 0.882511] sky2: driver version 1.30[ 0.886445]
>> ivshmem-net 0000:00:01.0: enabling device (0000 -> 0002)[ 0.892506]
>> ivshmem-net 0000:00:01.0: TX memory at 0x00000000bfe80000, size
>> 0x000000000007f000[ 0.901024] ivshmem-net 0000:00:01.0: RX memory at
>> 0x00000000bfe01000, size 0x000000000007f000_ivshmem 0000:00:00.0:
>> state_table at 0x00000000bfd00000, size 0x0000000000001000om6s 3] dy[
>> 0.924815] uio_ivshmem 0000:00:00.0: rw_section at 0x00000000bfd01000, size
>> 0x0000000000009000[ 0.933489] uio_ivshmem 0000:00:00.0: input_sections
>> at 0x00000000bfd0a000, size 0x0000000000006000[ 0.942511] uio_ivshmem
>> 0000:00:00.0: output_section at 0x00000000bfd0e000, size
>> 0x0000000000002000[ 0.951977] VFIO - User Level meta-driver version:
>> 0.3[ 0.957373] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI)
>> Driver[ 0.963176] ehci-pci: EHCI PCI platform driver[ 0.967627]
>> ehci-platform: EHCI generic platform driver[ 0.972839] ohci_hcd: USB 1.1
>> 'Open' Host Controller (OHCI) Driver[ 0.978981] ohci-pci: OHCI PCI
>> platform driver[ 0.983424] ohci-platform: OHCI generic platform
>> driver[ 0.988740] usbcore: registered new interface driver
>> usb-storage[ 0.994651] usbcore: registered new interface driver
>> usbserial_generic[ 1.001115] usbserial: USB Serial support registered
>> for generic[ 1.007108] usbcore: registered new interface driver
>> ftdi_sio[ 1.012831] usbserial: USB Serial support registered for FTDI
>> USB Serial Device[ 1.020135] usbcore: registered new interface driver
>> usb_serial_simple[ 1.026643] usbserial: USB Serial support registered
>> for carelink[ 1.032709] usbserial: USB Serial support registered for
>> zio[ 1.038351] usbserial: USB Serial support registered for funsoft[
>> 1.044350] usbserial: USB Serial support registered for flashloader[
>> 1.050679] usbserial: USB Serial support registered for google[ 1.056583]
>> usbserial: USB Serial support registered for libtransistor[ 1.063090]
>> usbserial: USB Serial support registered for vivopay[ 1.069080]
>> usbserial: USB Serial support registered for moto_modem[ 1.075333]
>> usbserial: USB Serial support registered for motorola_tetra[ 1.081930]
>> usbserial: USB Serial support registered for novatel_gps[ 1.088278]
>> usbserial: USB Serial support registered for hp4x[ 1.093993] usbserial:
>> USB Serial support registered for suunto[ 1.099901] usbserial: USB
>> Serial support registered for siemens_mpi[ 1.107246] i2c /dev entries
>> driver[ 1.110345] Bluetooth: HCI UART driver ver 2.3[ 1.114127]
>> Bluetooth: HCI UART protocol H4 registered[ 1.119245] Bluetooth: HCI
>> UART protocol BCSP registered[ 1.124556] Bluetooth: HCI UART protocol LL
>> registered[ 1.129660] Bluetooth: HCI UART protocol ATH3K registered[
>> 1.135056] Bluetooth: HCI UART protocol Three-wire (H5) registered[
>> 1.141326] Bluetooth: HCI UART protocol Broadcom registered[ 1.146950]
>> Bluetooth: HCI UART protocol QCA registered[ 1.152285] imx-cpufreq-dt:
>> probe of imx-cpufreq-dt failed with error -2[ 1.159033] sdhci: Secure
>> Digital Host Controller Interface driver[ 1.164990] sdhci: Copyright(c)
>> Pierre Ossman[ 1.169392] Synopsys Designware Multimedia Card Interface
>> Driver[ 1.175449] sdhci-pltfm: SDHCI platform and OF driver helper[
>> 1.181146] sdhci-esdhc-imx 30b40000.mmc: could not get pinctrl[ 1.218013]
>> mmc2: SDHCI controller on 30b40000.mmc [30b40000.mmc] using ADMA[
>> 1.222834] ledtrig-cpu: registered to indicate activity on CPUs[
>> 1.229160] usbcore: registered new interface driver usbhid[ 1.233823]
>> usbhid: USB HID core driver[ 1.238352] No fsl,qman node[ 1.240462]
>> Freescale USDPAA process driver[ 1.244627] fsl-usdpaa: no region
>> found[ 1.248477] Freescale USDPAA process IRQ driver[ 1.257304]
>> pktgen: Packet Generator for packet performance testing. Version: 2.75[
>> 1.262307] NET: Registered protocol family 26[ 1.267090] NET: Registered
>> protocol family 10[ 1.271591] Segment Routing with IPv6[ 1.274573]
>> NET: Registered protocol family 17[ 1.279040] Bluetooth: RFCOMM TTY
>> layer initialized[ 1.283840] Bluetooth: RFCOMM socket layer
>> initialized[ 1.288955] Bluetooth: RFCOMM ver 1.11[ 1.292683]
>> Bluetooth: BNEP (Ethernet Emulation) ver 1.3[ 1.297958] Bluetooth: BNEP
>> filters: protocol multicast[ 1.303185] Bluetooth: BNEP socket layer
>> initialized[ 1.308126] Bluetooth: HIDP (Human Interface Emulation) ver
>> 1.2[ 1.314021] Bluetooth: HIDP socket layer initialized[ 1.319004]
>> 8021q: 802.1Q VLAN Support v1.8[ 1.323167] lib80211: common routines for
>> IEEE802.11 drivers[ 1.328915] 9pnet: Installing 9P2000 support[
>> 1.333060] tsn generic netlink module v1 init...[ 1.337781] Key type
>> dns_resolver registered[ 1.342482] registered taskstats version 1[
>> 1.346064] Loading compiled-in X.509 certificates[ 1.352505] hctosys:
>> unable to open rtc device (rtc0)[ 1.355965] cfg80211: Loading
>> compiled-in X.509 certificates for regulatory database[ 1.365244]
>> cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'[ 1.370196]
>> platform regulatory.0: Direct firmware load for regulatory.db failed with
>> error -2[ 1.371872] clk: Not disabling unused clocks[ 1.378719]
>> platform regulatory.0: Falling back to sysfs fallback for:
>> regulatory.db[ 1.382975] ALSA device list:[ 1.393625] No soundcards
>> found.[ 1.397057] Warning: unable to open an initial console.[
>> 1.402301] Waiting for root device /dev/mmcblk1p2...[ 1.417055] mmc2: new
>> DDR MMC card at address 0001[ 1.419499] mmcblk2: mmc2:0001 DG4016 14.7
>> GiB[ 1.423711] mmcblk2boot0: mmc2:0001 DG4016 partition 1 4.00 MiB[
>> 1.429619] mmcblk2boot1: mmc2:0001 DG4016 partition 2 4.00 MiB[ 1.435431]
>> mmcblk2rpmb: mmc2:0001 DG4016 partition 3 4.00 MiB, chardev (237:0)[
>> 1.452011] mmcblk2: p1 p2[ 62.528001] cfg80211: failed to load
>> regulatory.db*
>>
>> --
>> You received this message because you are subscribed to the Google Groups
>> "Jailhouse" group.
>> To unsubscribe from this group and stop receiving emails from it, send an
>> email to [email protected] <javascript:>.
>> To view this discussion on the web visit
>> https://groups.google.com/d/msgid/jailhouse-dev/11e37b92-3146-4194-877f-f79ab746d971o%40googlegroups.com
>>
>> <https://groups.google.com/d/msgid/jailhouse-dev/11e37b92-3146-4194-877f-f79ab746d971o%40googlegroups.com?utm_medium=email&utm_source=footer>
>> .
>>
>
>
> --
>
>
--
You received this message because you are subscribed to the Google Groups
"Jailhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/jailhouse-dev/fed47e44-bfa7-47a7-bad7-a60088a9d2a6o%40googlegroups.com.
