Hi Jean-Pierre when I add the following delay
var word big_loop = 1 while big_loop != 0 loop big_loop = big_loop + 1 end loop after the USB disabling (UCON=0, UCFG=0 ) it seems to work with your bootloader procedure Albert ----- Original Message ----- From: "jean-pierre mandon" <[email protected]> To: "jallib" <[email protected]> Sent: Sunday, November 01, 2009 11:15 PM Subject: [jallib] Re: USB don't work for me !! > > Hi albert and thanks for answer, > > Yes my board is the Pinguino board with a 4550, it seems to be the > same than your board. > I tried with and without bootloader but the result is the same. > > i use the svn version of jallib. > > To make JAL work with Pinguino bootloader, i made an hex converter and > a special version of pinguino bootloader. My goal is to integrate JAL > to Pinguino IDE. > The working pinguino bootloader for JAL is version 2.2 > Hex file must be translated with jal2pinguino.py > then vascobooy1.1.py can be used > > For the compiler, this is the command line: > -no-variable-reuse -no-fuse -loader18 8224 -s /home/mandon/sources/ > mouse4550/;/home/mandon/jal/jallib-read-only/lib/ > 18f4550_usb_hid_mouse.jal > > i added in the beginning of your program 2 instructions: > UCON=0 > UCFG=0 > > this instructions stop the USB module. If not, the chip keep the last > usb descriptors ( pinguino bootloader ). > > all the sources and the bootloader version 2.2 is here: > www.pictec.org/jal/ > README file explain how to use jal2pinguino. > > if it is necessary, i can send you the bootloader sources. > > Hope you can help me to solve the problem, i have a lot of ideas to > extend pinguino to JAL. > The first project is this zigbee module: > http://www.hackinglab.org/zigbee/index.html > > Thanks for help > > Jean-Pierre > > > On 1 nov, 22:13, "a.faber" <[email protected]> wrote: >> Hi Jean-Pierre >> Need a bit more info in order to diagnose the problem: >> >> First, what kind of board are you using? (your Pinguino board?) >> Are you using a bootloader? >> Which compiler settings are you using? >> Which version of the archive are you using, just checked the most up to >> date >> version of Jallib, and seems to work fine >> >> Albert >> >> ----- Original Message ----- >> From: "jean-pierre mandon" <[email protected]> >> To: "jallib" <[email protected]> >> Sent: Sunday, November 01, 2009 1:04 PM >> Subject: [jallib] USB don't work for me !! >> >> > Hi guys, >> >> > I try to use 18f4550_usb_hid_mouse.jal and it don't work. It's >> > probably a problem on my side but i don't find where is my error. >> >> > System: linux >> > compiler: JALV2 2.4l >> > sample file: 18f4550_usb_hid_mouse.jal >> > processor: 18F4550 >> > ( a blink test on the card works ) >> >> > result: >> > lsusb output >> > Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub >> > Bus 004 Device 034: ID 04d8:0000 Microchip Technology, Inc. >> > Bus 004 Device 005: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port >> > HUB >> > Bus 004 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port >> > HUB >> > Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub >> > Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub >> > Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub >> > Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub >> > Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub >> > Bus 002 Device 003: ID 045e:0083 Microsoft Corp. Basic Optical Mouse >> > Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub >> > Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub >> >> > USB microchip device is recognized >> >> > dmesg output: >> > [11023.050587] usb 4-3.1: new full speed USB device using ehci_hcd and >> > address 34 >> > [11028.144860] usb 4-3.1: unable to read config index 0 descriptor/ >> > start: -32 >> > [11028.144870] usb 4-3.1: chopping to 0 config(s) >> > [11028.147733] usb 4-3.1: string descriptor 0 read error: -32 >> > [11028.149232] usb 4-3.1: string descriptor 0 read error: -32 >> > [11028.151964] usb 4-3.1: no configuration chosen from 0 choices >> >> > i don't see where is the problem. >> > If somebody can help me........... >> >> > Jean-Pierre > > > --~--~---------~--~----~------------~-------~--~----~ You received this message because you are subscribed to the Google Groups "jallib" group. To post to this group, send email to [email protected] To unsubscribe from this group, send email to [email protected] For more options, visit this group at http://groups.google.com/group/jallib?hl=en -~----------~----~----~----~------~----~------~--~---
