Any thoughts on this? I don't think libraries should be dependant on a
specific timer, the user should be able to choose what timer to use.

For example, the library timer0_isr_interval.jal is dependant on
timer0.

What if someone wants to use two libraries that are both dependant on
timer0?

Matt.

On Aug 8, 3:21 am, mattschinkel <[email protected]> wrote:
> Hey guys, I was thinking about creating a timer library for general
> setup of a timer. It would be nice to have a library that will allow
> users to choose a timer for use with other libraries. I need some
> advise/assistance.
>
> My servo libraries allow the user to choose a timer via a constant for
> example:
> const SERVO_SLAVE_USE_TIMER = 1 -- choose a timer
>
> Here's how it is setup in my libraries. After doing the alias, I can
> use the new aliases in the rest of the lib for whatever timer the user
> selected. It may be better to place these aliases in their own new
> timer lib.
>
> -- setup servo 1 to 8 timer aliases for the timer the user selected
> if SERVO_SLAVE_USE_TIMER == 0 then
>    -- set special timer0 settings
>    t0con_psa  = 0  -- assign prescaler to timer0
>    -- set timer registers to timer0
>    alias servo_slave_tmr      is TMR0            -- timer interval
>    alias servo_slave_cs       is T0CON_T0CS      -- timer clock source
> bit
>    alias servo_slave_ie       is INTCON_TMR0IE   -- interrupt enable
>    alias servo_slave_if       is INTCON_TMR0IF   -- interrupt overflow
> bit
>    alias servo_slave_ps       is T0CON_T0PS      -- timer prescaler
> select bits
>    alias servo_slave_on       is T0CON_TMR0ON    -- timer on
>
>    if defined(TMR0H) then
>       const SERVO_SLAVE_TIMER_SIZE = 16
>    else
>       const SERVO_SLAVE_TIMER_SIZE = 8
>    end if
>
> elsif SERVO_SLAVE_USE_TIMER == 1 then
>    -- set special timer1 settings
>    ;t1con_tmr1on = 1               -- enables timer 1
>    -- set timer registers to timer1
>    alias servo_slave_tmr      is TMR1             -- timer interval
>    alias servo_slave_cs       is T1CON_TMR1CS     -- timer clock
> source bit
>    alias servo_slave_ie       is PIE1_TMR1IE      -- interrupt enable
>    alias servo_slave_if       is PIR1_TMR1IF      -- interrupt
> overflow bit
>    alias servo_slave_ps       is T1CON_T1CKPS     -- timer prescaler
> select bits
>    alias servo_slave_on       is T1CON_TMR1ON     -- timer on
>
>    if defined(TMR1H) then
>       const SERVO_SLAVE_TIMER_SIZE = 16
>    else
>       const SERVO_SLAVE_TIMER_SIZE = 8
>    end if
> elsif SERVO_SLAVE_USE_TIMER == 3 then
>    ;t3con_tmr3on = 1               -- enables timer 3
>    -- set timer registers to timer3
>    alias servo_slave_tmr      is TMR3             -- timer interval
>    alias servo_slave_cs       is T3CON_TMR3CS     -- timer clock
> source bit
>    alias servo_slave_ie       is PIE2_TMR3IE      -- interrupt enable
>    alias servo_slave_if       is PIR2_TMR3IF      -- interrupt
> overflow bit
>    alias servo_slave_ps       is T3CON_T3CKPS     -- timer prescaler
> select bits
>    alias servo_slave_on       is T3CON_TMR3ON    -- timer on
>
>    if defined(TMR3H) then
>       const SERVO_SLAVE_TIMER_SIZE = 16
>    else
>       const SERVO_SLAVE_TIMER_SIZE = 8
>    end if
> end if
>
> Timers are quite alike for all PIC's. There are a few differences
> however:
> 1. Timer 0 can be either 8 bit or 16 bit. I am able to detect the
> size, as seen above.
> 2. Timer 0 requires setting of t0con_psa  = 0. I suppose I can check
> if a tXcon_psa is defined for the selected timer, and set it to 0 if
> required. Not sure if this setting will be the same on all PIC's.
> 3. Prescaler means different things on different PIC's and timers.
>
> So, mainly I have an issue with #3. Is there any way to detect what
> prescaler settings are available? Can constants or a constant array be
> added to the device files (to hold prescaler speeds that are
> available), or is it better to place it in a timer lib for each PIC?
>
> Is there even any efficient way to read these from any file microchip
> provides?
>
> 18f4620 - Timer0 prescalers:
>
> 111 = 1:256
> 110 = 1:128
> 101 = 1:64
> 100 = 1:32
> 011 = 1:16
> 010 = 1:8
> 001 = 1:4
> 000 = 1:2
>
> 18f4620 - Timer1 prescalers:
> 11 = 1:8
> 10 = 1:4
> 01 = 1:2
> 00 = 1:1
>
> 18f4620 - Timer2 prescalers:
> 0 0= Prescaler is 1
> 01 = Prescaler is 4
> 1x = Prescaler is 16
>
> 18f4620 - Timer3 prescalers:
> 11 = 1:8
> 10 = 1:4
> 01 = 1:2
> 00 = 1:1
>
> I haven't used timer2 much, not sure how it works (haven't had time to
> check). For now, I only use timers 0, 1 & 3. I currently assume the
> prescaler settings are the same as above for all PICs. Is it simply
> safe enouf to assume this?
>
> Matt.

-- 
You received this message because you are subscribed to the Google Groups 
"jallib" group.
To post to this group, send email to [email protected].
To unsubscribe from this group, send email to 
[email protected].
For more options, visit this group at 
http://groups.google.com/group/jallib?hl=en.

Reply via email to