Hi Rob, Very helpfull info here. 32Mhz code worked ok and even solved some other issue about RS232 comms that was happening. Later on will test 40MHz (10MHz xtal)... Thank you very much.
Cheers Filipe Santos On Wednesday, August 17, 2022 at 6:17:52 PM UTC+1 [email protected] wrote: > Hi Filipe, > > About the ansel error. It seems to be in your program, not in a library so > I think you should remove those lines. > > About the 40 MHz. Do you need 40 MHz using a crystal or is 32 MHz using > the internal oscillator sufficient? Below the code I think that should work > for 32 MHz but you need to test it. I always use a blink sample program as > starting point. > > -- This program uses the internal oscillator at 32 MHz. > pragma target clock 32_000_000 -- oscillator frequency > -- > pragma target OSC INTOSC_NOCLKOUT -- internal oscillator > pragma target WDT CONTROL -- watchdog > pragma target XINST DISABLED -- do not use extended > instructionset > pragma target DEBUG DISABLED -- no debugging > pragma target BROWNOUT DISABLED -- no brownout reset > pragma target FCMEN DISABLED -- no clock monitoring > pragma target IESO DISABLED -- no int/ext osc > switching > pragma target LVP ENABLED -- low voltage programming > pragma target MCLR EXTERNAL -- external reset > -- > -- The configuration bit settings above are only a selection, sufficient > -- for this program. Other programs may need more or different settings. > -- > WDTCON_SWDTEN = OFF -- disable WDT > OSCCON_SCS = 0 -- select primary oscillator > OSCCON_IRCF = 0b111 -- 8 MHz > OSCTUNE_PLLEN = TRUE -- 4xPLL > > For 40 MHz it may be something like this. You need a 10 MHz crystal for > this configuration: > > -- This program assumes that a 10 MHz resonator or crystal > -- is connected to pins OSC1 and OSC2. > pragma target clock 40_000_000 -- oscillator frequency > -- > pragma target OSC HS_PLL -- crystal with 4xPLL > pragma target WDT CONTROL -- watchdog > pragma target XINST DISABLED -- do not use extended > instructionset > pragma target DEBUG DISABLED -- no debugging > pragma target BROWNOUT DISABLED -- no brownout reset > pragma target FCMEN DISABLED -- no clock monitoring > pragma target IESO DISABLED -- no int/ext osc > switching > pragma target LVP ENABLED -- low voltage programming > pragma target MCLR EXTERNAL -- external reset > -- > -- The configuration bit settings above are only a selection, sufficient > -- for this program. Other programs may need more or different settings. > -- > WDTCON_SWDTEN = OFF -- disable WDT > OSCCON_SCS = 0 -- select primary oscillator > OSCTUNE_PLLEN = TRUE -- 4xPLL > -- > > Kind regards, > > Rob > > ------------------------------ > *Van:* [email protected] <[email protected]> namens flyway38 < > [email protected]> > *Verzonden:* woensdag 17 augustus 2022 17:29 > *Aan:* jallib <[email protected]> > *Onderwerp:* Re: [jallib] PIC18F2580 ADC CHANNELS > > Hello Rob, > > Tried today your code for the "new" ADC and have installed already the new > JAL 1.7.0 > Heres th error log: > > [Error] (DMTM_v3.00_1.jal) [Line 168] "ansel_ans3" not defined > [Error] (DMTM_v3.00_1.jal) [Line 168] unexpected token: ansel_ans3 > > Any help will be appreciated. > Thank you. > > Cheers, > Filipe Santos. > On Tuesday, August 16, 2022 at 8:32:24 PM UTC+1 flyway38 wrote: > > Hi Rob, > > Thanks for your help. > Am using PIC18F2580. > > Cheers, > Filipe Santos > > On Tuesday, August 16, 2022 at 7:30:10 PM UTC+1 [email protected] wrote: > > Hi Filipe, > Your question about the 40 MHz depends on the pic you are using > > Which one is that? > Kind regards. > > Rob > > Met vriendelijke groet, > Rob Jansen > ------------------------------ > *From:* [email protected] <[email protected]> on behalf of > flyway38 <[email protected]> > *Sent:* Tuesday, August 16, 2022 8:16:59 PM > *To:* jallib <[email protected]> > *Subject:* Re: [jallib] PIC18F2580 ADC CHANNELS > > Hi Rob > > Thank you very much for the heads up. > Managed to make it work, doing some changes to "old" ADC_Channels... :D > But will move my JAL install to the new one. > Thanks once again. > > Now am trying to make this PIC to run at 40MHz... > Any help here? > Thanks > > > Cheers, > Filipe Santos. > > On Tuesday, August 16, 2022 at 6:10:43 PM UTC+1 [email protected] wrote: > > Hello Filipe, > > I had to look this up since the library adc_channels.jal does not exist > anymore since Jallib release 1.5.0. It was there in 1.4.0 and currently we > are at 1.7.0. > > The problem was that the library was not maintainable anymore so it was > removed and the configuration of the channels was moved to the program of > the user. Also the use of JANSEL was removed from all device files because > of the same reason. > > So I suggest you download the latest Jallib release and look at one of the > adc sample files. They are all updated to incorporate this change. > > For example, a typical adc set-up in your main program will then look > something like this but this is PIC dependent. > > -- Step 1: ADC analog input pin setup > const byte ADC_CHANNEL = 3 -- potmeter connected to > pin_AN3 > ANSEL_ANS3 = TRUE -- port 3 is analog input > (default) > pin_AN3_direction = input > -- Step 2: Set VDD and VSS as Vref > ADCON0_VCFG = FALSE > -- Step 3: Use Frc as ADC clock > ANSEL_ADCS = 0b011 > const ADC_RSOURCE = 4_700 -- Input resistance: 4.7K > potmeter > -- Now we can include the library > include adc > -- And initialize the whole with our parameters > adc_init() > > Kind regards, > > Rob > > ------------------------------ > *Van:* [email protected] <[email protected]> namens flyway38 < > [email protected]> > *Verzonden:* dinsdag 16 augustus 2022 17:58 > *Aan:* jallib <[email protected]> > *Onderwerp:* [jallib] PIC18F2580 ADC CHANNELS > > Hello to all, > > Am coding for this PIC (18F2580) now. > Need to use ADC and compiling fails with this log; > > LOG: > jal jalv25r6 (compiled Oct 29 2021) > generating p-code > 992 tokens, 700421 chars; 14125 lines; 19 files > generating PIC code pass 1 > generating PIC code pass 2 > 1293 data accesses checked, 0 errors > 87 skips checked, 0 errors > writing result > C:\JALLIB~1\lib/adc_channels.jal:3315: " > Unable to configure ADC channels. > Configuration is supposed to be done using ANS bits > but it seems there's no ANS bits for this PIC. > Maybe your PIC isn't supported, please report !" > 1 errors, 0 warnings > > Any help will be appreciated. > Thank you. > > Kind regards, > Filipe Santos. > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/ab00461c-c965-43b7-8ef4-c8d726515d85n%40googlegroups.com > > <https://groups.google.com/d/msgid/jallib/ab00461c-c965-43b7-8ef4-c8d726515d85n%40googlegroups.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/3c8637ac-86dc-4ac5-ae44-b6b19cd98228n%40googlegroups.com > > <https://groups.google.com/d/msgid/jallib/3c8637ac-86dc-4ac5-ae44-b6b19cd98228n%40googlegroups.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/7e26946d-2b76-45da-bfd1-9fab42194087n%40googlegroups.com > > <https://groups.google.com/d/msgid/jallib/7e26946d-2b76-45da-bfd1-9fab42194087n%40googlegroups.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "jallib" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/jallib/7019365a-9955-4f16-b0d5-a33f3d45573bn%40googlegroups.com.
