Hi Vasile, Did you used AT commands in that BLE project? Does your code interpret received messages? Am struggling with that code... Thanks
Cheers, Filipe Santos On Friday, December 2, 2022 at 11:04:06 AM UTC vasile wrote: > Great. :) > > On Fri 2 Dec 2022, 11:32 AM flyway38 <[email protected] wrote: > >> Hi Vasile, yes, have used hyperterminal to understand what was not >> working and found out some issues about connections and some other bugs in >> AT commands to be sent. >> Also had success in solving this issue. >> >> Cheers, >> FS >> >> On Thursday, December 1, 2022 at 6:21:51 AM UTC vasile wrote: >> >>> I would try first with a standard terminal connected to your GSM module, >>> and a link between two computers. >>> Perhaps there are some delays you need to comply with. That will solve >>> any connection issues (if any). >>> I remember the BLE communication on some moisture sensors I >>> manufactured, they had the same problem but finally worked. >>> >>> On Wed, Nov 30, 2022 at 8:21 PM flyway38 <[email protected]> wrote: >>> >>>> Hello all, >>>> >>>> Am trying to implement code to send SMS and make a Call (for testing >>>> only) using this PIC16F19176 with a GSM module: GA6-B. >>>> Heres the arduino code: >>>> >>>> // >>>> --------------------------------------------------------------------------- >>>> >>>> // Example Support of GOOUUU TECH IOT-GA6-B Gprs Gsm Module >>>> // >>>> --------------------------------------------------------------------------- >>>> >>>> #include <SoftwareSerial.h> >>>> #define GSM_RX 2 // Arduino pin 2 to URX >>>> #define GSM_TX 3 // Arduino pin 3 to URX >>>> SoftwareSerial sim(GSM_RX, GSM_TX); // >>>> // The GSM >>>> String number = "07905582XXX"; //-> change with your number >>>> void setup() { >>>> Serial.begin(9600); // GPS on 0,1 pin >>>> Serial.println("System Started..."); >>>> sim.begin(115200); >>>> delay(1000); >>>> Serial.println("Communicating GSM/GPS....."); >>>> sms(); //send sms >>>> call(); //call to us >>>> } >>>> void loop() { >>>> //do your code >>>> } //loop >>>> //-----------GSM Function >>>> --------------------------------------------------------- >>>> void sms() >>>> { >>>> Serial.println ("Sending Message"); >>>> sim.println("AT+CMGF=1"); //Sets the GSM Module in Text Mode >>>> delay(1000); >>>> Serial.println ("Set SMS Number"); >>>> sim.println("AT+CMGS=\"" + number + "\"\r"); //Mobile phone number to >>>> send message >>>> delay(1000); >>>> String SMS = "Sample SMS is sending....."; //sms content >>>> sim.println(SMS); >>>> delay(100); >>>> sim.println((char)26);// ASCII code of CTRL+Z >>>> delay(1000); >>>> } >>>> void call() { >>>> sim.print (F("ATD")); >>>> sim.print (number); >>>> sim.print (F(";\r\n")); >>>> } >>>> >>>> And here relevant part of my code (not working): >>>> -- >>>> include pps >>>> pps_control_lock(FALSE) >>>> RC6PPS = PPS_TX1 -- TX1 re-assigned to C6 (default) >>>> RX1PPS = PPS_RC7 -- C7 re-assigned to RX1 (default) >>>> pps_control_lock(TRUE) >>>> -- >>>> -- >>>> -- >>>> -- ok, now setup serial >>>> --const serial_hw_baudrate = 999_000 >>>> -- (115_200 / 256_000 / 512_000 já testados com sucesso) >>>> -- >>>> -- Include and initialize serial hardware library. >>>> const serial_hw_baudrate = 115200 >>>> --const serial_hw_baudrate = 9600 >>>> alias pin_TX_direction is pin_C6_direction -- Transmit pin. >>>> alias pin_RX_direction is pin_C7_direction -- Receive pin. >>>> include serial_hardware >>>> serial_hw_init() >>>> -- >>>> -- output library >>>> include print >>>> -- >>>> include delay >>>> -- >>>> const byte AT1[] = "ATD" >>>> const byte AT2[] = "XXXMyNumberXXX" >>>> const byte AT3[] = ";" >>>> -- >>>> forever loop >>>> -- >>>> led = OFF >>>> delay_1ms(10_000) >>>> -- >>>> led = ON >>>> print_string(serial_hw_data,AT1) >>>> print_string(serial_hw_data,AT2) >>>> print_string(serial_hw_data,AT3) >>>> --print_crlf(serial_hw_data) >>>> delay_1ms(5_000) >>>> -- >>>> end loop >>>> >>>> Testing only with a CALL making. No success so far. >>>> AT commands are sent (received and read in computer) >>>> Any help will be great. >>>> Thank you very much. >>>> >>>> Best Regards, >>>> Filipe Santos. >>>> >>>> -- >>>> You received this message because you are subscribed to the Google >>>> Groups "jallib" group. >>>> To unsubscribe from this group and stop receiving emails from it, send >>>> an email to [email protected]. >>>> To view this discussion on the web visit >>>> https://groups.google.com/d/msgid/jallib/142573ae-b364-4ba8-b01c-96a7355af724n%40googlegroups.com >>>> >>>> <https://groups.google.com/d/msgid/jallib/142573ae-b364-4ba8-b01c-96a7355af724n%40googlegroups.com?utm_medium=email&utm_source=footer> >>>> . >>>> >>> -- >> You received this message because you are subscribed to the Google Groups >> "jallib" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> > To view this discussion on the web visit >> https://groups.google.com/d/msgid/jallib/b8f54e75-bb5e-4342-8626-2995b5dae198n%40googlegroups.com >> >> <https://groups.google.com/d/msgid/jallib/b8f54e75-bb5e-4342-8626-2995b5dae198n%40googlegroups.com?utm_medium=email&utm_source=footer> >> . >> > -- You received this message because you are subscribed to the Google Groups "jallib" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/jallib/f4fe3980-a492-4fab-9950-ccd6d11df600n%40googlegroups.com.
