Sorry folks, but, as I said before, I have never done anything compiling before. To learn all this is perhaps an impossible task for me. I have made an attempt, but I think it would only be possible if I took a course for this. And that is not something for the jallib environment in my opinion. If Evan wants to send me the hex file I can try to see if something like that fits into my plans. By the way, I never hide my gratitude for your efforts and I have been able to do a lot of fun things because of your work. regards Hans
Op zondag 4 februari 2024 om 22:15:55 UTC+1 schreef Pinhead: > Ok, now I get it! > > I didn't understand you asked to three OTHER people, therefore my > confusion.... > > I am genuinely willing to help, since I think the solution to your problem > is close at hand. > > What are the error messages you received ? This will be a good starting > point to investigate and further help you > > Kind regards, > > David > > Le 4 févr. 2024, à 21:23, Hans van Veldhuizen <[email protected]> a > écrit: >> >> Hello Pinhead >> Initially I asked if there would be a jal lib for the link I provided. >> I followed your instructions but received error messages from MPlab. >> Because I think this falls outside the Jal event, I approached three >> other people who turned out to get the same negative result. >> I then emailed the creator who indicated in his article that he always >> wanted to be helpful. >> There is a receipt-, but no read- confirmation and no answer. >> Hence my conclusion. >> I get the impression that you experience this as unpleasant. >> And that disappoints me. >> regards >> Hans >> >> Op zondag 4 februari 2024 om 20:06:05 UTC+1 schreef Pinhead: >> >>> Hi, >>> >>> I thinking i don't understand your message.... >>> >>> I try to help you by describing the steps to follow to achieve your >>> goal. I was not intended to do it for you since I do not know your >>> requirements ..... >>> >>> And in fact, I was expecting an answer with your findings and more >>> questions so that I can continue to help you.... >>> >>> Did I miss something? >>> >>> >>> Le 3 févr. 2024, à 20:46, Hans van Veldhuizen <[email protected] >>> <http://href>> a écrit: >>>> >>>> A classic example of an internet cadaver. Three experienced IT people >>>> were unable to convert the asm file into a working hex file and the maker >>>> does not respond to emails. >>>> Fortunately, JAL is still alive and kicking. >>>> >>>> Op dinsdag 23 januari 2024 om 13:49:24 UTC+1 schreef Pinhead: >>>> >>>>> If you don't need to change the program, just download the hex file >>>>> from instructable, rename it with "hex" and program your chip with your >>>>> favorite tool as you do usually >>>>> >>>>> Ensure you are using the same pic model as used in the description, >>>>> otherwise you will not be able to program it without changing the >>>>> "include" >>>>> declaration in the asm file, and maybe one or two other things >>>>> >>>>> Easiest is of course to keep the chosen pic >>>>> >>>>> >>>>> Le 23 janv. 2024, à 13:44, Pinhead <pinhead.be <http://href>@gmail.com >>>>> target=_blank>[email protected]> a écrit: >>>>>> >>>>>> It's really easy. Let's do it together... >>>>>> >>>>>> Do you have MPLABX installed? If not, go to this page: >>>>>> https://www.microchip.com/en-us/tools-resources/develop/mplab-x-ide >>>>>> >>>>>> and download the version for you, windows, Linux or Mac. This will >>>>>> take a while. >>>>>> >>>>>> Once downloaded, Double click on the file to install it. You may >>>>>> keep all the options to default, but to make it lighter, you may >>>>>> unchecked >>>>>> the mplab c16 and c32 compilers: you will need them >>>>>> >>>>>> Wait until the installation is done. This will also take a while..... >>>>>> >>>>>> >>>>>> Now, download the source file "new" from instructable. >>>>>> Rename it with an "asm" extension >>>>>> >>>>>> Now, open it in mplab. >>>>>> If you want to modify some parameters, Now is the good time to do so. >>>>>> >>>>>> Once done, compile your asm file. >>>>>> >>>>>> >>>>>> It's that simple. You will now have a correct hex file to program >>>>>> your own pic. >>>>>> >>>>>> Le 23 janv. 2024, à 13:26, Hans van Veldhuizen <[email protected] >>>>>> <http://href>> a écrit: >>>>>>> >>>>>>> Hello Pinheadand others >>>>>>> Unfortunately, that goes far beyond my knowledge and capabilities. >>>>>>> I'll have to find someone to do this for me. >>>>>>> >>>>>>> >>>>>>> Op maandag 22 januari 2024 om 17:05:28 UTC+1 schreef Pinhead: >>>>>>> >>>>>>>> Try with the asm file, load it in mplab, and from there you should >>>>>>>> be able to compile it to a hex file and program your pic >>>>>>>> >>>>>>>> Verify that you use the same pic as declared in the asm file >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>> Le 22 janv. 2024, à 17:01, Hans van Veldhuizen < >>>>>>>> [email protected] <http://href>> a écrit: >>>>>>>>> >>>>>>>>> Hi Pinhead, >>>>>>>>> The example looks what i need, i have download the hex file but >>>>>>>>> this this is a tmp file. >>>>>>>>> Changed the extension in hex . Pickit3plus gave an eror when >>>>>>>>> tried to load. >>>>>>>>> regards >>>>>>>>> Hans >>>>>>>>> >>>>>>>>> >>>>>>>>> Op maandag 22 januari 2024 om 16:36:45 UTC+1 schreef Pinhead: >>>>>>>>> >>>>>>>>>> Hi Hans, >>>>>>>>>> >>>>>>>>>> What are your requirements? >>>>>>>>>> Is this example from Instructable not a good starting point ? >>>>>>>>>> >>>>>>>>>> I do not know what you plan to do, but there is also the >>>>>>>>>> possibility to decode DTMF tones. Some specialized ICs are still >>>>>>>>>> available >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> Le 22 janv. 2024, à 10:28, Hans van Veldhuizen < >>>>>>>>>> [email protected] <http://href>> a écrit: >>>>>>>>>>> >>>>>>>>>>> Hello all, >>>>>>>>>>> I would like to use the frequencies of a variable audio signal >>>>>>>>>>> to make things respond to it. I found this : >>>>>>>>>>> https://www.instructables.com/Frequency-Detector-using-PIC-12F683-Processor/ >>>>>>>>>>> >>>>>>>>>>> Is there something like this in the Jal area? >>>>>>>>>>> regards >>>>>>>>>>> Hans >>>>>>>>>>> >>>>>>>>>>> -- You received this message because you are subscribed to the Google Groups "jallib" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/jallib/cb0be27b-8dfd-4337-8e50-468a387e0cf5n%40googlegroups.com.
