hey guys am tryin to set iscsi initiator (client) on my RHEL 5 babe
ive already disabled CHAP on both side ( initiator and target)
anyway result ( echo $? = 1 )
:( :( :(
:( :(
:(
*************
[r...@localhost ~]# iscsid -f -d 8
iscsid: transport class version 2.0-724. iscsid version 2.0-865
iscsid: Can not bind IPC socket
iscsid: iscsid_exit
iscsid: in ctldev_close
**************************************
[r...@localhost ~]# iscsiadm -m discovery -t sendtargets -p
192.168.1.101
iscsiadm: connection to discovery address 192.168.1.101 failed
*******************
[r...@localhost ~]# iscsiadm -m discovery -t sendtargets -p
192.168.1.101:3260
iscsiadm: connection to discovery address 192.168.1.101 failed
************************************
[r...@localhost ~]# iscsiadm -m node
iscsiadm: no records found!
******************************
[r...@localhost ~]# cat /etc/iscsi/iscsid.conf
#
# Open-iSCSI default configuration.
# Could be located at /etc/iscsi/iscsid.conf or ~/.iscsid.conf
#
# Note: To set any of these values for a specific node/session run
# the iscsiadm --mode node --op command for the value. See the README
# and man page for iscsiadm for details on the --op command.
#
#############################
# NIC/HBA and driver settings
#############################
# open-iscsi can create a session and bind it to a NIC/HBA.
# To set this up see the example iface config file.
#*****************
# Startup settings
#*****************
# To request that the iscsi initd scripts startup a session set to
"automatic".
# node.startup = automatic
#
# To manually startup the session set to "manual". The default is
automatic.
node.startup = automatic
# *************
# CHAP Settings
# *************
# To enable CHAP authentication set node.session.auth.authmethod
# to CHAP. The default is None.
#node.session.auth.authmethod = CHAP
# To set a CHAP username and password for initiator
# authentication by the target(s), uncomment the following lines:
#node.session.auth.username = joe
#node.session.auth.password = 123456789123
# To set a CHAP username and password for target(s)
# authentication by the initiator, uncomment the following lines:
#node.session.auth.username_in = joe
#node.session.auth.password_in = 123456789123
# To enable CHAP authentication for a discovery session to the target
# set discovery.sendtargets.auth.authmethod to CHAP. The default is
None.
#discovery.sendtargets.auth.authmethod = CHAP
# To set a discovery session CHAP username and password for the
initiator
# authentication by the target(s), uncomment the following lines:
#discovery.sendtargets.auth.username = username
#discovery.sendtargets.auth.password = password
# To set a discovery session CHAP username and password for target(s)
# authentication by the initiator, uncomment the following lines:
#discovery.sendtargets.auth.username_in = username_in
#discovery.sendtargets.auth.password_in = password_in
# ********
# Timeouts
# ********
#
# See the iSCSI REAME's Advanced Configuration section for tips
# on setting timeouts when using multipath or doing root over iSCSI.
#
# To specify the length of time to wait for session re-establishment
# before failing SCSI commands back to the application when running
# the Linux SCSI Layer error handler, edit the line.
# The value is in seconds and the default is 120 seconds.
node.session.timeo.replacement_timeout = 120
# To specify the time to wait for login to complete, edit the line.
# The value is in seconds and the default is 15 seconds.
node.conn[0].timeo.login_timeout = 15
# To specify the time to wait for logout to complete, edit the line.
# The value is in seconds and the default is 15 seconds.
node.conn[0].timeo.logout_timeout = 15
# To specify the intervale to send iSCSI Nop-outs as pings
# to the target edit this the line.
# The value is in seconds and the default is 10 seconds.
node.conn[0].timeo.noop_out_interval = 10
# To specify the time to wait for a Nop-out response before failing
# the connection, edit this line. Failing the connection will
# cause IO to be failed back to the SCSI layer. If using dm-multipath
# this will cause the IO to be failed to the multipath layer.
# The value is in seconds and the default is 15 seconds.
node.conn[0].timeo.noop_out_timeout = 15
#******
# Retry
#******
# To speficy the number of times iscsiadm should retry a login
# to the target when we first login, modify the following line.
# The default is 4. Valid values are any integer value. This only
# affects the initial login. Setting it to a high value can slow
# down the iscsi service startup. Setting it to a low value can
# cause a session to not get logged into, if there are distuptions
# during startup or if the network is not ready at that time.
node.session.initial_login_retry_max = 4
################################
# session and device queue depth
################################
# To control how many commands the session will queue set
# node.session.cmds_max to an integer between 2 and 2048 that is also
# a power of 2. The default is 128.
node.session.cmds_max = 128
# To control the device's queue depth set node.session.queue_depth
# to a value between 1 and 128. The default is 128.
node.session.queue_depth = 32
#***************
# iSCSI settings
#***************
# To enable R2T flow control (i.e., the initiator must wait for an R2T
# command before sending any data), uncomment the following line:
#
#node.session.iscsi.InitialR2T = Yes
#
# To disable R2T flow control (i.e., the initiator has an implied
# initial R2T of "FirstBurstLength" at offset 0), uncomment the
following line:
#
# The defaults is No.
node.session.iscsi.InitialR2T = No
#
# To disable immediate data (i.e., the initiator does not send
# unsolicited data with the iSCSI command PDU), uncomment the
following line:
#
#node.session.iscsi.ImmediateData = No
#
# To enable immediate data (i.e., the initiator sends unsolicited data
# with the iSCSI command packet), uncomment the following line:
#
# The default is Yes
node.session.iscsi.ImmediateData = Yes
# To specify the maximum number of unsolicited data bytes the
initiator
# can send in an iSCSI PDU to a target, edit the following line.
#
# The value is the number of bytes in the range of 512 to (2^24-1) and
# the default is 262144
node.session.iscsi.FirstBurstLength = 262144
# To specify the maximum SCSI payload that the initiator will
negotiate
# with the target for, edit the following line.
#
# The value is the number of bytes in the range of 512 to (2^24-1) and
# the defauls it 16776192
node.session.iscsi.MaxBurstLength = 16776192
# To specify the maximum number of data bytes the initiator can
receive
# in an iSCSI PDU from a target, edit the following line.
#
# The value is the number of bytes in the range of 512 to (2^24-1) and
# the default is 131072
node.conn[0].iscsi.MaxRecvDataSegmentLength = 131072
# To specify the maximum number of data bytes the initiator can
receive
# in an iSCSI PDU from a target during a discovery session, edit the
# following line.
#
# The value is the number of bytes in the range of 512 to (2^24-1) and
# the default is 32768
#
discovery.sendtargets.iscsi.MaxRecvDataSegmentLength = 32768
# To allow the targets to control the setting of the digest checking,
# with the initiator requesting a preference of enabling the checking,
uncommen
# the following lines (Data digests are not supported and on ppc/ppc64
# both header and data digests are not supported.):
#node.conn[0].iscsi.HeaderDigest = CRC32C,None
#
# To allow the targets to control the setting of the digest checking,
# with the initiator requesting a preference of disabling the
checking,
# uncomment the following lines:
#node.conn[0].iscsi.HeaderDigest = None,CRC32C
#
# To enable CRC32C digest checking for the header and/or data part of
# iSCSI PDUs, uncomment the following lines:
#node.conn[0].iscsi.HeaderDigest = CRC32C
#
# To disable digest checking for the header and/or data part of
# iSCSI PDUs, uncomment the following lines:
#node.conn[0].iscsi.HeaderDigest = None
#
# The default is to never use DataDigests and to allow the target to
control
# the setting of the HeaderDigest checking with the initiator
requesting
# a preference of disabling the checking.
#************
# Workarounds
#************
# Some targets like IET prefer after an initiator has sent a task
# management function like an ABORT TASK or LOGICAL UNIT RESET, that
# it does not respond to PDUs like R2Ts. To enable this behavior
uncomment
# the following line (The default behavior is No):
# node.session.iscsi.FastAbort = Yes
# Some targets like Equalogic prefer that after an initiator has sent
# a task management function like an ABORT TASK or LOGICAL UNIT RESET,
that
# it continue to respond to R2Ts. To enable this uncomment this line
(This
# is the default behavior):
node.session.iscsi.FastAbort = No
[r...@localhost ~]#
******
even our friend google didnt help
i cant find any solution @ all
except ,,,, migrate to window ( setup in Window --Next then ---Next
then --- finish --Done
then lets party not like linux @ all )
although migration process usually bring many problems and ( big
delay)
:)
--~--~---------~--~----~------------~-------~--~----~
### Jordan Linux Users Group ###
http://Jolug.org/
http://groups.google.com/group/Jolug
### Ubuntu Jordan LoCo Team ###
https://wiki.ubuntu.com/JordanTeam
http://lists.ubuntu.com/ubuntu-jo
### Ojuba Linux ###
http://ojuba.org/
### Jordan PHP ###
http://groups.google.com/group/JoPHP
-~----------~----~----~----~------~----~------~--~---
