coz on cisco side ,i use active . maybe the srx don't support vpls link agg .
The VPLS implementation on a J Series or SRX Series device is similar to VPLS implementations on M Series, T Series, and MX Series routers, with the following exceptions: J Series or SRX Series devices do not support aggregated Ethernet interfaces. Therefore, aggregated Ethernet interfaces between CE devices ------------------ Best Regards, Bruno ------------------ Original ------------------ From: "Palmentieri, Nunzia (NSN - IT/Rome)"<[email protected]>; Date: Mon, Apr 23, 2012 04:17 PM To: "ext bruno.juniper"<[email protected]>; "juniper-nsp"<[email protected]>; Subject: R: [j-nsp] vpls multihome link agg test hi, why lacp passive? ________________________________ Da: [email protected] per conto di ext bruno.juniper Inviato: dom 22/04/2012 9.11 A: juniper-nsp Oggetto: [j-nsp] vpls multihome link agg test hi experts, i am using srx test link aggregation to prevent loops as well as provide added bandwidth between PE and CE in vpls. the agg can't success. config is below. i hope my config is wrong . i have check many times. PE(SRX210)===CE(3750) fe-0/0/5 { vlan-tagging; encapsulation vlan-vpls; unit 600 { encapsulation vlan-vpls; vlan-id 600; family vpls; } } fe-0/0/6 { fastether-options { 802.3ad ae0; } } fe-0/0/7 { fastether-options { 802.3ad ae0; } } ae0 { vlan-tagging; encapsulation vlan-vpls; aggregated-ether-options { link-speed 100m; lacp { passive; periodic fast; } } unit 600 { encapsulation vlan-vpls; vlan-id 600; family vpls; } } === cisco config cisco#show run int f0/47 Building configuration... Current configuration : 147 bytes ! interface FastEthernet0/47 switchport trunk encapsulation dot1q switchport mode trunk channel-protocol lacp channel-group 1 mode active end cisco#show run int f0/48 Building configuration... Current configuration : 147 bytes ! interface FastEthernet0/48 switchport trunk encapsulation dot1q switchport mode trunk channel-protocol lacp channel-group 1 mode active end cisco#show run int port-channel 1 Building configuration... Current configuration : 92 bytes ! interface Port-channel1 switchport trunk encapsulation dot1q switchport mode trunk end [edit interfaces] root@PE# run show lacp interfaces Aggregated interface: ae0 LACP state: Role Exp Def Dist Col Syn Aggr Timeout Activity fe-0/0/6 Actor No Yes No No No Yes Fast Passive fe-0/0/6 Partner No Yes No No No Yes Fast Passive fe-0/0/7 Actor No Yes No No No Yes Fast Passive fe-0/0/7 Partner No Yes No No No Yes Fast Passive LACP protocol: Receive State Transmit State Mux State fe-0/0/6 Defaulted No periodic Detached fe-0/0/7 Defaulted No periodic Detached SW1-CE4#show lacp 1 nei Flags: S - Device is requesting Slow LACPDUs F - Device is requesting Fast LACPDUs A - Device is in Active mode P - Device is in Passive mode Channel group 1 neighbors Partner's information: LACP port Admin Oper Port Port Port Flags Priority Dev ID Age key Key Number State Fa0/47 SP 0 0000.0000.0000 646s 0x0 0x0 0x0 0x0 Fa0/48 SP 0 0000.0000.0000 646s 0x0 0x0 0x0 0x0 ------------------ Best Regards, Bruno _______________________________________________ juniper-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/juniper-nsp _______________________________________________ juniper-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/juniper-nsp
