Folks,
Here's my situation.
I have an MX5 configured to dual-homed to two sets of SRX240 in a cluster with
the intention of running OSPF + BGP between them.
The links are straight point to points with no switch in between.
OSPF between the two works alright, so does static. BGPv4 and BGPv6 (static
routing) works OK.
My problem is with OSPF3, no matter what I configured, the session just won't
come up.
Curiously, the link-locals are not seen on both sides.
ihsan@b1> show ipv6 neighbors
IPv6 Address Linklayer Address State Exp Rtr Secure
Interface
1111:1111:1::222 00:10:db:ff:10:03 reachable 5 yes no
ge-1/0/9.0
ihsan@a1-node0> show ipv6 neighbors
IPv6 Address Linklayer Address State Exp Rtr Secure
Interface
1111:1111:1::223 a8:d0:e5:52:f8:28 reachable 31 yes no
reth3.0
ihsan@a1-node0> show interfaces reth0 | match fe80
Destination: fe80::/64, Local: fe80::210:dbff:feff:1000
ihsan@b1> show interfaces irb.0 | match fe80
Destination: fe80::/64, Local: fe80::aad0:e5ff:fe52:f828
The OSPF3 hellos are sent out on both sides but only the MX is not receiving
hence the current state of OSPF3 Init on the SRX.
The config is just plain routing. No fancy MPLS, CoS stuff etc.
I have another MX5 and SRX240, plain routing with IPv6, without cluster and
IRBs. OSPFv3 works alright.
So I'm guessing it's either the cluster setup or the IRB or maybe combo of both.
I'm on 11.4R3.7.
MX5
---
ihsan@b1> show configuration interfaces irb
unit 0 {
description "L3 interface to ACS bridge domain";
family inet {
address 111.111.16.223/31;
}
family inet6 {
address 1111:1111:1::223/127;
}
}
ihsan@b1> show configuration interfaces ge-1/0/9
description "To ge-1/0/0::a1-node0";
mtu 9192;
encapsulation ethernet-bridge;
unit 0 {
family bridge;
}
ihsan@b1> show configuration interfaces ge-1/1/9
description "To ge-1/0/0::a1-node1";
mtu 9192;
encapsulation ethernet-bridge;
unit 0 {
family bridge;
}
ihsan@b1> show configuration bridge-domains
acs-bridge {
domain-type bridge;
vlan-id none;
interface ge-1/0/9.0;
interface ge-1/1/9.0;
routing-interface irb.0;
}
ihsan@b1> show configuration protocols ospf3
area 0.0.0.0 {
interface lo0.0 {
passive;
}
interface irb.0 {
interface-type p2p;
}
}
SRX cluster
---
{primary:node0}
ihsan@a1-node0> show configuration interfaces reth3
mtu 9192;
redundant-ether-options {
redundancy-group 4;
}
unit 0 {
bandwidth 1g;
family inet {
address 111.111.16.222/31;
}
family inet6 {
address 1111:1111:1::222/127;
}
}
{primary:node0}
ihsan@a1-node0> show configuration protocols ospf3
area 0.0.0.0 {
interface lo0.0 {
passive;
}
interface reth3.0 {
interface-type p2p;
}
}
ihsan@a1-node0> show ospf3 neighbor
ID Interface State Pri Dead
111.111.16.159 reth3.0 Init 128 33
Neighbor-address fe80::aad0:e5ff:fe52:f828
_______________________________________________
juniper-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/juniper-nsp
