Ive seen this happen with bad sfp as well as not setting mode to active
Try setting up a simple ptp to remove portchan setting out of the equation, if
that works and shows up/up on both ends, try setting to mode active on the
portchan settings
If ur ptp doesn't work... Try diff port, negotiation settings or more
importantly another sfp brand or type on the juniper side, juniper is picky
with the brands of sfp used, specially copper
--
Payam Chychi
Network Engineer / Security Specialist
On Wednesday, 13 March, 2013 at 3:40 PM, snort bsd wrote:
> hi all:
>
> i have a cisco 3750 fastethernet switch connecting to a juniper 4200, with
> portchannel on cisco side and aggregated interface juniper side. the cisco
> side shows as "connected" but juniper side remain down. could anyone give me
> some ideas? no lacp activated on both side.
>
> for cisco:
>
> cisco-3750#sh int fast1/0/9
> FastEthernet1/0/9 is up, line protocol is up (connected)
> Hardware is Fast Ethernet, address is 0018.b99f.5d8b (bia 0018.b99f.5d8b)
> MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation ARPA, loopback not set
>
> cisco-3750#sh interfaces por10
> Port-channel10 is up, line protocol is up (connected)
> Hardware is EtherChannel, address is 0018.b99f.5d8c (bia 0018.b99f.5d8c)
> MTU 1500 bytes, BW 200000 Kbit, DLY 100 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation ARPA, loopback not set
> Full-duplex, 100Mb/s, link type is auto, media type is unknown
> input flow-control is off, output flow-control is unsupported
> Members in this channel: Fa1/0/9 Fa1/0/10
>
>
> interface Port-channel10
> switchport access vlan 100
> switchport mode access
>
> interface FastEthernet1/0/9
> switchport access vlan 100
> switchport mode access
> switchport nonegotiate
> channel-group 10 mode on
>
>
> for juniper:
>
> user@4200-1# run show interfaces terse ge-0/0/9
> Interface Admin Link Proto Local Remote
> ge-0/0/9 up down
> ge-0/0/9.0 up down aenet --> ae1.0
>
> user@4200-1# run show interfaces ae1 terse
> Interface Admin Link Proto Local Remote
> ae1 up down
> ae1.0 up down eth-switch
>
>
> user@4200-1# show interfaces ge-0/0/9
> ether-options {
> no-auto-negotiation;
> link-mode full-duplex;
> speed {
> 100m;
> }
> 802.3ad ae1;
> }
>
> user@4200-1# show interfaces ae1
>
> ae1 {
> aggregated-ether-options {
> minimum-links 1;
> link-speed 100m;
> }
> unit 0 {
> family ethernet-switching {
> port-mode access;
> }
> }
> }
>
>
> _dave
> _______________________________________________
> juniper-nsp mailing list [email protected]
> https://puck.nether.net/mailman/listinfo/juniper-nsp
>
>
_______________________________________________
juniper-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/juniper-nsp
