Hi thanks for the kind reply You are not exporting anything inside BGP ? can you please post the bgp_rip export under the routing instance?
Thanks BR, Mohammad On Wed, Aug 21, 2013 at 7:43 PM, Harry Reynolds <[email protected]> wrote: > Here is a sample l3vpn vrf that is using rip, along with vrf ifl, IBGP, > IGP, and LDP/MPLS settings that work on a mx in 11.4/12.3; HTHs > > > {master}[edit] > regress@halfpint# show routing-instances vrf_200 > instance-type vrf; > interface ge-3/0/9.991; > interface ge-3/0/9.992; > interface ge-3/0/9.993; > interface ge-3/0/9.994; > interface ge-3/0/9.995; > interface ge-3/0/9.996; > interface ge-3/0/9.997; > interface ge-3/0/9.998; > interface ge-3/0/9.999; > interface ge-3/0/9.1000; > route-distinguisher 65056:2000; > vrf-target target:65056:200; > vrf-table-label; > protocols { > rip { > group vrf_200 { > export bgp_rip; > neighbor ge-3/0/9.991; > neighbor ge-3/0/9.992; > neighbor ge-3/0/9.993; > neighbor ge-3/0/9.994; > neighbor ge-3/0/9.995; > neighbor ge-3/0/9.996; > neighbor ge-3/0/9.997; > neighbor ge-3/0/9.998; > neighbor ge-3/0/9.999; > neighbor ge-3/0/9.1000; > } > } > } > > > {master}[edit] > regress@halfpint# show interfaces ge-3/0/9.991 > vlan-id 991; > family inet { > address 51.51.4.193/30; > } > > > > {master}[edit] > regress@halfpint# show protocols bgp > group internal { > type internal; > local-address 192.168.1.10; > family inet { > any; > } > family inet-vpn { > unicast; > } > family inet6-vpn { > unicast; > } > family route-target; > export next-hop-self; > neighbor 192.168.1.1; > neighbor 192.168.1.2; > } > > > << this is ldp based: > > {master}[edit] > regress@halfpint# show protocols ldp > interface ge-3/2/9.0; > interface ge-5/0/0.0; > interface ge-5/0/2.0; > interface xe-5/2/0.0; > interface lo0.0; > session-protection timeout 2; > igp-synchronization holddown-interval 10; > > {master}[edit] > regress@halfpint# show protocols mpls > ipv6-tunneling; > icmp-tunneling; > interface ge-3/2/9.0; > interface ge-5/0/0.0; > interface ge-5/0/2.0; > interface xe-5/2/0.0; > > > {master}[edit] > regress@halfpint# show protocols ospf > rib-group ospf-rib; > traffic-engineering; > reference-bandwidth 10g; > area 0.0.0.0 { > interface fxp0.0 { > disable; > } > interface lo0.0 { > passive; > } > interface xe-5/2/0.0 { > metric 800; > } > interface ge-3/2/9.0 { > metric 100; > } > > . . . > > > > -----Original Message----- > From: juniper-nsp [mailto:[email protected]] On Behalf > Of Mohammad Khalil > Sent: Wednesday, August 21, 2013 2:12 AM > To: [email protected] > Subject: [j-nsp] MPLS L3VPN > > Hi > I am trying to configure MPLS L3VPN between two sites using RIP and the > PE-CE routing protocol , I went through the documents but did not > understand properly the commands syntax , can anyone provide me with > example? > > Thanks > _______________________________________________ > juniper-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/juniper-nsp > > > > _______________________________________________ juniper-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/juniper-nsp
