Hi, Check this link - https://www.juniper.net/documentation/en_US/junos/topics/concept/vpn-proxy-bgp-route-target-filtering-understanding.html
If you configure the rest of the routers with family route-target r3 and r4 will stop sending the proxy route you see. Or just use RR. Ivan, On Tue, Jun 6, 2017 at 9:01 PM, Mihai <[email protected]> wrote: > Update: using route policies with rtf-prefix-list works, but > rtf-prefix-lists are supported from Junos 12.2 and I have devices with > older software. > I am more interested if this is a 'normal' behavior. > > Regards, > Mihai > > > On 06/06/2017 07:41 PM, Mihai wrote: > >> Hi, >> >> I have three routers (r1,r3,r4) and a full mesh IBGP between them. >> R1 is configured with inet-vpn , R3 and R4 with inet-vpn and route-target. >> >> r1# show protocols bgp >> group IBGP { >> type internal; >> local-address 1.1.1.1; >> family inet-vpn { >> unicast; >> } >> neighbor 3.3.3.3; >> neighbor 4.4.4.4; >> } >> >> r3# show protocols bgp >> group IBGP { >> type internal; >> local-address 3.3.3.3; >> family inet-vpn { >> unicast; >> } >> family route-target; >> neighbor 1.1.1.1; >> neighbor 4.4.4.4; >> } >> >> r4# show protocols bgp >> group IBGP { >> type internal; >> local-address 4.4.4.4; >> family inet-vpn { >> unicast; >> } >> family route-target; >> neighbor 1.1.1.1; >> neighbor 3.3.3.3; >> } >> >> I don't understand why R3 and R4 are advertising the default rt route >> (0:0:0/0) in this topology as I am not using route reflectors. >> >> r3# run show table bgp.rt >> Jun 06 18:10:05 >> >> bgp.rtarget.0: 1 destinations, 2 routes (1 active, 0 holddown, 0 hidden) >> >> + = Active Route, - = Last Active, * = Both >> >> 0:0:0/0 >> *[RTarget/5] 00:10:46 >> Type Default >> Local >> [BGP/170] 00:10:42, localpref 100, from 4.4.4.4 >> AS path: I, validation-state: unverified >> > to 10.0.2.6 via ge-0/0/4.34 >> >> r4# run show table bgp.rt >> >> bgp.rtarget.0: 1 destinations, 2 routes (1 active, 0 holddown, 0 hidden) >> + = Active Route, - = Last Active, * = Both >> >> 0:0:0/0 >> *[RTarget/5] 00:11:13 >> Type Default >> Local >> [BGP/170] 00:11:09, localpref 100, from 3.3.3.3 >> AS path: I, validation-state: unverified >> > to 10.0.2.5 via ge-0/0/3.34 >> >> If I want to create a VRF/L2VPN/VPLS on R3 (first) and R4 (later) the >> service will be down because R3 will not readvertise the VRF/L2VPN/VPLS >> when is receiving the VPN RT/ROUTE from R4. >> The only solution to get the R3 VPN route on R4 is by requesting it with >> a ROUTE REFRESH (clear soft-inbound) from R4. >> >> This has been tested on Junos 13.3 and 14.1. >> >> PS: I don't want to configure R3/R4 with "keep all" and I can't make any >> configuration that will reset the BGP sessions. >> >> Does this look like a BUG? >> >> Regards, >> Mihai >> >> _______________________________________________ > juniper-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/juniper-nsp > -- Best Regards! Ivan Ivanov _______________________________________________ juniper-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/juniper-nsp
