Public bug reported:
This is somewhat similar in issue to lp#1377596.
I have a "Lenovo ThinkCentre m900 Tiny" with an "Intel 600p" NVMe drive
in it.
As far as I can tell from dissembling the FADT PCIe ASPM is not set to
disabled but the ports are not enabled in UEFI during boot.
I also notice that the PCIe ASPM debug files are not in sysfs like they
normally are ie: link_state
I tried running the following manually but I think it must not be enough
as the NVMe drive does not run any cooler as it does in a system with
known working ASPM.
setpci -s 00:1b.0 0x50.B=0x3
setpci -s 00:1c.0 0x50.B=0x3
setpci -s 01:00.0 0x80.B=0x3
setpci -s 02:00.0 0x50.B=0x3
I noticed via lspci that the root ports say ASPM not supported even
though the FADT doesn't have them disabled. Is that the reason its still
not working and how do I work around that issue?
Also is there something specific I can tell Lenovo to do to fix this
issue on their end, if it can't be worked around in Linux? I have an
open case with them via the UEFI engineering team but so far its been
slow going since I don't have anything concrete to tell them to fix.
===
00:1b.0 PCI bridge: Intel Corporation Sunrise Point-H PCI Root Port #17 (rev
f1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 122
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: df100000-df1fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #17, Speed 8GT/s, Width x4, ASPM not supported,
Exit Latency L0s <1us, L1 <16us
ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 8GT/s, Width x4, TrErr- Train- SlotClk+ DLActive+
BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #0, PowerLimit 25.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR+, OBFF
Not Supported ARIFwd+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+,
OBFF Disabled ARIFwd-
LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB,
EqualizationComplete+, EqualizationPhase1+
EqualizationPhase2+, EqualizationPhase3+,
LinkEqualizationRequest-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee00218 Data: 0000
Capabilities: [90] Subsystem: Lenovo Sunrise Point-H PCI Root Port
Capabilities: [a0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt+
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd-
EgressCtrl- DirectTrans-
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd-
EgressCtrl- DirectTrans-
Capabilities: [220 v1] #19
Kernel driver in use: pcieport
Kernel modules: shpchp
ProblemType: Bug
DistroRelease: Ubuntu 17.04
Package: linux-image-4.10.0-19-generic 4.10.0-19.21
ProcVersionSignature: Ubuntu 4.10.0-19.21-generic 4.10.8
Uname: Linux 4.10.0-19-generic x86_64
ApportVersion: 2.20.4-0ubuntu4
Architecture: amd64
AudioDevicesInUse:
Cannot stat file /proc/2050/fd/24: Stale file handle
Cannot stat file /proc/2050/fd/25: Stale file handle
USER PID ACCESS COMMAND
/dev/snd/controlC0: ubuntu-mate 2046 F.... pulseaudio
CasperVersion: 1.380
Date: Fri Apr 14 04:10:41 2017
LiveMediaBuild: Ubuntu-MATE 17.04 "Zesty Zapus" - Release amd64 (20170412)
MachineType: LENOVO 10FMCTO
ProcEnviron:
TERM=xterm
PATH=(custom, no user)
LANG=en_US.UTF-8
SHELL=/bin/bash
ProcFB: 0 inteldrmfb
ProcKernelCmdLine: BOOT_IMAGE=/casper/vmlinuz.efi debug ignore_loglevel
pcie_aspm.policy=powersave pcie_aspm=force file=/cdrom/preseed/hostname.seed
boot=casper quiet splash ---
PulseList: Error: command ['pacmd', 'list'] failed with exit code 1: No
PulseAudio daemon running, or not running as session daemon.
RelatedPackageVersions:
linux-restricted-modules-4.10.0-19-generic N/A
linux-backports-modules-4.10.0-19-generic N/A
linux-firmware 1.164
SourcePackage: linux
UpgradeStatus: No upgrade log present (probably fresh install)
dmi.bios.date: 03/07/2017
dmi.bios.vendor: LENOVO
dmi.bios.version: FWKT6CA
dmi.board.name: 30D0
dmi.board.vendor: LENOVO
dmi.board.version: SDK0K17763 WIN 1801925111491
dmi.chassis.type: 3
dmi.chassis.vendor: LENOVO
dmi.chassis.version: Default string
dmi.modalias:
dmi:bvnLENOVO:bvrFWKT6CA:bd03/07/2017:svnLENOVO:pn10FMCTO:pvrLenovoProduct:rvnLENOVO:rn30D0:rvrSDK0K17763WIN1801925111491:cvnLENOVO:ct3:cvrDefaultstring:
dmi.product.name: 10FMCTO
dmi.product.version: Lenovo Product
dmi.sys.vendor: LENOVO
** Affects: linux (Ubuntu)
Importance: Undecided
Status: Confirmed
** Tags: amd64 apport-bug zesty
--
You received this bug notification because you are a member of Kernel
Packages, which is subscribed to linux in Ubuntu.
https://bugs.launchpad.net/bugs/1682711
Title:
PCIe ASPM disabled even when enabled in FADT and pcie_aspm=force /
setpci used
Status in linux package in Ubuntu:
Confirmed
Bug description:
This is somewhat similar in issue to lp#1377596.
I have a "Lenovo ThinkCentre m900 Tiny" with an "Intel 600p" NVMe
drive in it.
As far as I can tell from dissembling the FADT PCIe ASPM is not set to
disabled but the ports are not enabled in UEFI during boot.
I also notice that the PCIe ASPM debug files are not in sysfs like
they normally are ie: link_state
I tried running the following manually but I think it must not be
enough as the NVMe drive does not run any cooler as it does in a
system with known working ASPM.
setpci -s 00:1b.0 0x50.B=0x3
setpci -s 00:1c.0 0x50.B=0x3
setpci -s 01:00.0 0x80.B=0x3
setpci -s 02:00.0 0x50.B=0x3
I noticed via lspci that the root ports say ASPM not supported even
though the FADT doesn't have them disabled. Is that the reason its
still not working and how do I work around that issue?
Also is there something specific I can tell Lenovo to do to fix this
issue on their end, if it can't be worked around in Linux? I have an
open case with them via the UEFI engineering team but so far its been
slow going since I don't have anything concrete to tell them to fix.
===
00:1b.0 PCI bridge: Intel Corporation Sunrise Point-H PCI Root Port #17 (rev
f1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 122
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: df100000-df1fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag- RBE+
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #17, Speed 8GT/s, Width x4, ASPM not supported,
Exit Latency L0s <1us, L1 <16us
ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 8GT/s, Width x4, TrErr- Train- SlotClk+
DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #0, PowerLimit 25.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR+,
OBFF Not Supported ARIFwd+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR+,
OBFF Disabled ARIFwd-
LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB,
EqualizationComplete+, EqualizationPhase1+
EqualizationPhase2+, EqualizationPhase3+,
LinkEqualizationRequest-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee00218 Data: 0000
Capabilities: [90] Subsystem: Lenovo Sunrise Point-H PCI Root Port
Capabilities: [a0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt+
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap-
ChkEn-
Capabilities: [140 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+
UpstreamFwd- EgressCtrl- DirectTrans-
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir-
UpstreamFwd- EgressCtrl- DirectTrans-
Capabilities: [220 v1] #19
Kernel driver in use: pcieport
Kernel modules: shpchp
ProblemType: Bug
DistroRelease: Ubuntu 17.04
Package: linux-image-4.10.0-19-generic 4.10.0-19.21
ProcVersionSignature: Ubuntu 4.10.0-19.21-generic 4.10.8
Uname: Linux 4.10.0-19-generic x86_64
ApportVersion: 2.20.4-0ubuntu4
Architecture: amd64
AudioDevicesInUse:
Cannot stat file /proc/2050/fd/24: Stale file handle
Cannot stat file /proc/2050/fd/25: Stale file handle
USER PID ACCESS COMMAND
/dev/snd/controlC0: ubuntu-mate 2046 F.... pulseaudio
CasperVersion: 1.380
Date: Fri Apr 14 04:10:41 2017
LiveMediaBuild: Ubuntu-MATE 17.04 "Zesty Zapus" - Release amd64 (20170412)
MachineType: LENOVO 10FMCTO
ProcEnviron:
TERM=xterm
PATH=(custom, no user)
LANG=en_US.UTF-8
SHELL=/bin/bash
ProcFB: 0 inteldrmfb
ProcKernelCmdLine: BOOT_IMAGE=/casper/vmlinuz.efi debug ignore_loglevel
pcie_aspm.policy=powersave pcie_aspm=force file=/cdrom/preseed/hostname.seed
boot=casper quiet splash ---
PulseList: Error: command ['pacmd', 'list'] failed with exit code 1: No
PulseAudio daemon running, or not running as session daemon.
RelatedPackageVersions:
linux-restricted-modules-4.10.0-19-generic N/A
linux-backports-modules-4.10.0-19-generic N/A
linux-firmware 1.164
SourcePackage: linux
UpgradeStatus: No upgrade log present (probably fresh install)
dmi.bios.date: 03/07/2017
dmi.bios.vendor: LENOVO
dmi.bios.version: FWKT6CA
dmi.board.name: 30D0
dmi.board.vendor: LENOVO
dmi.board.version: SDK0K17763 WIN 1801925111491
dmi.chassis.type: 3
dmi.chassis.vendor: LENOVO
dmi.chassis.version: Default string
dmi.modalias:
dmi:bvnLENOVO:bvrFWKT6CA:bd03/07/2017:svnLENOVO:pn10FMCTO:pvrLenovoProduct:rvnLENOVO:rn30D0:rvrSDK0K17763WIN1801925111491:cvnLENOVO:ct3:cvrDefaultstring:
dmi.product.name: 10FMCTO
dmi.product.version: Lenovo Product
dmi.sys.vendor: LENOVO
To manage notifications about this bug go to:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1682711/+subscriptions
--
Mailing list: https://launchpad.net/~kernel-packages
Post to : kernel-packages@lists.launchpad.net
Unsubscribe : https://launchpad.net/~kernel-packages
More help : https://help.launchpad.net/ListHelp
