Forwarding as per https://bugzilla.kernel.org/show_bug.cgi?id=65361#c1
On 08/08/13 14:15, Ken Sharp wrote: > wakeonlan fails if pm-hibernate used > > After issuing halt -p, wakeonlan works fine. after issuing pm-hibernate, > the machine will not wake up. > > interfaces: > auto eth0 > iface eth0 inet dhcp > up ethtool -s eth0 wol g > down ethtool -s eth0 wol g > > Settings for eth0: > Supported ports: [ TP MII ] > Supported link modes: 10baseT/Half 10baseT/Full > 100baseT/Half 100baseT/Full > Supported pause frame use: No > Supports auto-negotiation: Yes > Advertised link modes: 10baseT/Half 10baseT/Full > 100baseT/Half 100baseT/Full > Advertised pause frame use: No > Advertised auto-negotiation: Yes > Link partner advertised link modes: 10baseT/Half 10baseT/Full > 100baseT/Half 100baseT/Full > Link partner advertised pause frame use: Symmetric > Link partner advertised auto-negotiation: Yes > Speed: 100Mb/s > Duplex: Full > Port: MII > PHYAD: 32 > Transceiver: internal > Auto-negotiation: on > Supports Wake-on: pumbg > Wake-on: g > Current message level: 0x00000007 (7) > drv probe link > Link detected: yes > > 01:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. > RTL-8139/8139C/8139C+ (rev 10 > > Reported on Launchpad > https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1074110 > > $ cat /proc/version > Linux version 3.11.0-999-generic (apw@gomeisa) (gcc version 4.6.3 > (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #201308070514 SMP Wed Aug 7 09:24:40 > UTC 2013 > > $ lsb_release -rd > Description: Ubuntu 12.04.2 LTS > Release: 12.04 > > $ ./ver_linux > If some fields are empty or look unusual you may have an old version. > Compare to the current minimal requirements in Documentation/Changes. > > Linux oldhomeserver 3.11.0-999-generic #201308070514 SMP Wed Aug 7 > 09:24:40 UTC 2013 i686 i686 i386 GNU/Linux > > Gnu C 4.6 > Gnu make 3.81 > binutils 2.22 > util-linux 2.20.1 > mount support > module-init-tools 3.16 > e2fsprogs 1.42 > pcmciautils 018 > Linux C Library 2.15 > Dynamic linker (ldd) 2.15 > Procps 3.2.8 > Net-tools 1.60 > Kbd 1.15.2 > Sh-utils 8.13 > Modules Loaded zram dm_crypt nfsd nfs_acl auth_rpcgss nfs > fscache lockd binfmt_misc sunrpc gpio_ich lpc_ich serio_raw shpchp > intel_rng mac_hid hwmon_vid lp parport 8139too 8139cp mii > > $ cat /proc/cpuinfo > processor : 0 > vendor_id : GenuineIntel > cpu family : 6 > model : 8 > model name : Pentium III (Coppermine) > stepping : 3 > microcode : 0x10 > cpu MHz : 734.956 > cache size : 256 KB > fdiv_bug : no > f00f_bug : no > coma_bug : no > fpu : yes > fpu_exception : yes > cpuid level : 2 > wp : yes > flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov > pse36 mmx fxsr sse > bogomips : 1469.91 > clflush size : 32 > cache_alignment : 32 > address sizes : 36 bits physical, 32 bits virtual > power management: > > $ cat /proc/modules > zram 18166 1 - Live 0x00000000 (C) > dm_crypt 22524 0 - Live 0x00000000 > nfsd 246709 13 - Live 0x00000000 > nfs_acl 12771 1 nfsd, Live 0x00000000 > auth_rpcgss 49253 1 nfsd, Live 0x00000000 > nfs 162863 0 - Live 0x00000000 > fscache 52016 1 nfs, Live 0x00000000 > lockd 79198 2 nfsd,nfs, Live 0x00000000 > binfmt_misc 17268 1 - Live 0x00000000 > sunrpc 236600 23 nfsd,nfs_acl,auth_rpcgss,nfs,lockd, Live 0x00000000 > gpio_ich 13278 0 - Live 0x00000000 > lpc_ich 16987 0 - Live 0x00000000 > serio_raw 13189 0 - Live 0x00000000 > shpchp 32265 0 - Live 0x00000000 > intel_rng 12700 0 - Live 0x00000000 > mac_hid 13077 0 - Live 0x00000000 > hwmon_vid 12723 0 - Live 0x00000000 > lp 13359 0 - Live 0x00000000 > parport 40930 1 lp, Live 0x00000000 > 8139too 32770 0 - Live 0x00000000 > 8139cp 27168 0 - Live 0x00000000 > mii 13693 2 8139too,8139cp, Live 0x00000000 > > $ cat /proc/ioports > 0000-001f : dma1 > 0020-0021 : pic1 > 0040-0043 : timer0 > 0050-0053 : timer1 > 0060-0060 : keyboard > 0064-0064 : keyboard > 0070-0071 : rtc0 > 0080-008f : dma page reg > 00a0-00a1 : pic2 > 00c0-00df : dma2 > 00f0-00ff : fpu > 0170-0177 : 0000:00:1f.1 > 0170-0177 : ata_piix > 01f0-01f7 : 0000:00:1f.1 > 01f0-01f7 : ata_piix > 0376-0376 : 0000:00:1f.1 > 0376-0376 : ata_piix > 03c0-03df : vga+ > 03f6-03f6 : 0000:00:1f.1 > 03f6-03f6 : ata_piix > 0400-0403 : ACPI PM1a_EVT_BLK > 0404-0405 : ACPI PM1a_CNT_BLK > 0408-040b : ACPI PM_TMR > 0410-0415 : ACPI CPU throttle > 0428-042b : ACPI GPE0_BLK > 042c-042f : ACPI GPE1_BLK > 0430-0433 : iTCO_wdt > 0460-047f : iTCO_wdt > 0480-04bf : gpio_ich > 0480-04bf : 0000:00:1f.0 > 04c0-04cf : 0000:00:1f.3 > 0cf8-0cff : PCI conf1 > c000-cfff : PCI Bus 0000:01 > cc00-ccff : 0000:01:03.0 > cc00-ccff : 8139too > de00-de1f : 0000:00:1f.2 > de00-de1f : uhci_hcd > ff00-ff0f : 0000:00:1f.1 > ff00-ff0f : ata_piix > > $ cat /proc/iomem > 00000000-00000fff : reserved > 00001000-0009fbff : System RAM > 0009fc00-0009ffff : reserved > 000a0000-000bffff : Video RAM area > 000c0000-000c7fff : Video ROM > 000e0000-000fffff : reserved > 000f0000-000fffff : System ROM > 00100000-0beeffff : System RAM > 01000000-016680a2 : Kernel code > 016680a3-019bd17f : Kernel data > 01aa1000-01b94fff : Kernel bss > 0bef0000-0bef7fff : ACPI Tables > 0bef8000-0befffff : ACPI Non-volatile Storage > 0bf00000-0bffffff : reserved > dfc00000-dfcfffff : PCI Bus 0000:01 > e0000000-e3ffffff : 0000:00:01.0 > e7e00000-ebefffff : PCI Bus 0000:01 > e8000000-e80000ff : 0000:01:03.0 > e8000000-e80000ff : 8139too > ee000000-ee07ffff : 0000:00:01.0 > fff80000-ffffffff : reserved > > $ sudo lspci -vvv > 00:00.0 Host bridge: Intel Corporation 82810E DC-133 (GMCH) Graphics > Memory Controller Hub (rev 03) > Subsystem: Intel Corporation 82810E DC-133 (GMCH) Graphics Memory > Controller Hub > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR+ FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort+ >SERR- <PERR- INTx- > Latency: 0 > Kernel driver in use: agpgart-intel > > 00:01.0 VGA compatible controller: Intel Corporation 82810E DC-133 (CGC) > Chipset Graphics Controller (rev 03) (prog-if 00 [VGA controller]) > Subsystem: Giga-byte Technology Device 0200 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin A routed to IRQ 11 > Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M] > Region 1: Memory at ee000000 (32-bit, non-prefetchable) [size=512K] > Expansion ROM at <unassigned> [disabled] > Capabilities: [dc] Power Management version 1 > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > > 00:1e.0 PCI bridge: Intel Corporation 82801AA PCI Bridge (rev 02) > (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR+ FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 > I/O behind bridge: 0000c000-0000cfff > Memory behind bridge: e7e00000-ebefffff > Prefetchable memory behind bridge: dfc00000-dfcfffff > Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- <SERR- <PERR- > BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Kernel modules: shpchp > > 00:1f.0 ISA bridge: Intel Corporation 82801AA ISA Bridge (LPC) (rev 02) > Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Kernel driver in use: lpc_ich > Kernel modules: lpc_ich, intel-rng > > 00:1f.1 IDE interface: Intel Corporation 82801AA IDE Controller (rev 02) > (prog-if 80 [Master]) > Subsystem: Intel Corporation 82801AA IDE Controller > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) > [size=8] > Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) > [size=1] > Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) > [size=8] > Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) > [size=1] > Region 4: I/O ports at ff00 [size=16] > Kernel driver in use: ata_piix > > 00:1f.2 USB controller: Intel Corporation 82801AA USB Controller (rev > 02) (prog-if 00 [UHCI]) > Subsystem: Intel Corporation 82801AA USB Controller > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin D routed to IRQ 10 > Region 4: I/O ports at de00 [size=32] > Kernel driver in use: uhci_hcd > > 00:1f.3 SMBus: Intel Corporation 82801AA SMBus Controller (rev 02) > Subsystem: Intel Corporation 82801AA SMBus Controller > Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Interrupt: pin B routed to IRQ 0 > Region 4: I/O ports at 04c0 [size=16] > Kernel modules: i2c-i801 > > 01:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. > RTL-8139/8139C/8139C+ (rev 10) > Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 64 (8000ns min, 16000ns max) > Interrupt: pin A routed to IRQ 11 > Region 0: I/O ports at cc00 [size=256] > Region 1: Memory at e8000000 (32-bit, non-prefetchable) [size=256] > Capabilities: [50] Power Management version 2 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA > PME(D0-,D1+,D2+,D3hot+,D3cold+) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Kernel driver in use: 8139too > Kernel modules: 8139too, 8139cp > > $ cat /proc/scsi/scsi > Attached devices: > Host: scsi0 Channel: 00 Id: 01 Lun: 00 > Vendor: ATA Model: QUANTUM FIREBALL Rev: A01. > Type: Direct-Access ANSI SCSI revision: 05 > Host: scsi1 Channel: 00 Id: 00 Lun: 00 > Vendor: GoldStar Model: CD-RW CED-8080B Rev: 1.02 > Type: CD-ROM > > $ ls /proc > 1 1026 1406 1471 16 19 25 42 6 695 9 cpuinfo > fs kpagecount mounts slabinfo tty > 10 11 1461 1472 1641 2 26 44 619 7 986 crypto > interrupts kpageflags mtrr softirqs uptime > 1005 1110 1462 1473 1642 20 27 45 64 709 991 devices > iomem latency_stats net stat version > 1006 12 1463 1477 17 21 28 467 65 731 acpi diskstats > ioports loadavg pagetypeinfo swaps vmallocinfo > 1008 13 1466 1499 18 22 3 468 654 793 buddyinfo dma > irq locks partitions sys vmstat > 1013 1373 1467 15 1844 224 324 5 657 797 bus driver > kallsyms mdstat sched_debug sysrq-trigger zoneinfo > 1014 14 1468 1515 1859 225 326 579 666 8 cgroups > execdomains kcore meminfo schedstat sysvipc > 1021 1401 1469 1535 1867 23 39 584 67 856 cmdline fb > key-users misc scsi timer_list > 1023 1405 1470 1541 1868 24 41 586 694 895 consoles > filesystems kmsg modules self timer_stats > > $ sudo ethtool eth0 > Settings for eth0: > Supported ports: [ TP MII ] > Supported link modes: 10baseT/Half 10baseT/Full > 100baseT/Half 100baseT/Full > Supported pause frame use: No > Supports auto-negotiation: Yes > Advertised link modes: 10baseT/Half 10baseT/Full > 100baseT/Half 100baseT/Full > Advertised pause frame use: No > Advertised auto-negotiation: Yes > Link partner advertised link modes: 10baseT/Half 10baseT/Full > 100baseT/Half 100baseT/Full > Link partner advertised pause frame use: Symmetric > Link partner advertised auto-negotiation: Yes > Speed: 100Mb/s > Duplex: Full > Port: MII > PHYAD: 32 > Transceiver: internal > Auto-negotiation: on > Supports Wake-on: pumbg > Wake-on: g > Current message level: 0x00000007 (7) > drv probe link > Link detected: yes > > Taken as a guide to report this: > https://wiki.ubuntu.com/Bugs/Upstream/kernel > > Apologies if this is too much or not enough information, this is the > first time I have attempted to report a problem with the kernel. > > I looked through https://www.kernel.org/doc/Documentation/power/ but the > processes either didn't seem relevant or I simply didn't understand. If > you need me to run through the processes then please let me know. > > Specifically > https://www.kernel.org/doc/Documentation/power/basic-pm-debugging.txt > suggests that the debugging would test the wake/resume cycle, which I > don't think is relevant in this case. But I could be wrong! > > Thanks for your help, > > Ken -- You received this bug notification because you are a member of Kernel Packages, which is subscribed to linux in Ubuntu. https://bugs.launchpad.net/bugs/1074110 Title: wakeonlan fails if pm-hibernate used Status in The Linux Kernel: Unknown Status in “linux” package in Ubuntu: Confirmed Bug description: After issuing halt -p, wakeonlan works fine. after issuing pm- hibernate, the machine will not wake up. interfaces: auto eth0 iface eth0 inet dhcp up ethtool -s eth0 wol g down ethtool -s eth0 wol g Settings for eth0: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Link partner advertised pause frame use: Symmetric Link partner advertised auto-negotiation: Yes Speed: 100Mb/s Duplex: Full Port: MII PHYAD: 32 Transceiver: internal Auto-negotiation: on Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000007 (7) drv probe link Link detected: yes 01:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Not sure what else might be needed here, but apport-bug refuses to collect data for some reason. https://bugs.launchpad.net/ubuntu/+source/apport/+bug/1073830 Same is true of the latest upstream kernel: http://kernel.ubuntu.com/~kernel-ppa/mainline/v3.7-rc3-raring/ --- Architecture: i386 DistroRelease: Ubuntu 12.04 LiveMediaBuild: Ubuntu 7.10 "Gutsy Gibbon" - Release i386 (20071016) Package: linux 3.2.0.32.35 PackageArchitecture: i386 ProcEnviron: TERM=xterm LANG=en_GB.UTF-8 SHELL=/bin/bash Uname: Linux 3.7.0-030700rc3-generic i686 UnreportableReason: The running kernel is not an Ubuntu kernel UserGroups: To manage notifications about this bug go to: https://bugs.launchpad.net/linux/+bug/1074110/+subscriptions -- Mailing list: https://launchpad.net/~kernel-packages Post to : kernel-packages@lists.launchpad.net Unsubscribe : https://launchpad.net/~kernel-packages More help : https://help.launchpad.net/ListHelp