Launchpad has imported 4 comments from the remote bug at https://bugzilla.kernel.org/show_bug.cgi?id=194763.
If you reply to an imported comment from within Launchpad, your comment will be sent to the remote bug automatically. Read more about Launchpad's inter-bugtracker facilities at https://help.launchpad.net/InterBugTracking. ------------------------------------------------------------------------ On 2017-03-02T11:22:24+00:00 daznis wrote: Bond0 interface doesn't accept MTU higher than 1500.I can set MTU perfectly fine for the slave devices. Recreating the bond0 didn't help to up the MTU. 05:00.0 Ethernet controller: Intel Corporation 82599ES 10-Gigabit SFI/SFP+ Network Connection (rev 01) 05:00.1 Ethernet controller: Intel Corporation 82599ES 10-Gigabit SFI/SFP+ Network Connection (rev 01) [ 1626.840818] bond0: Invalid MTU 9000 requested, hw max 1500 [ 1668.913497] ixgbe 0000:05:00.0 enp5s0f0: changing MTU from 1500 to 9000 [ 1669.176015] ixgbe 0000:05:00.0 enp5s0f0: speed changed to 0 for port enp5s0f0 [ 1669.237523] ixgbe 0000:05:00.0 enp5s0f0: detected SFP+: 5 [ 1669.487920] ixgbe 0000:05:00.0 enp5s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX [ 1675.591234] ixgbe 0000:05:00.1 enp5s0f1: changing MTU from 1500 to 9000 [ 1675.855232] ixgbe 0000:05:00.1 enp5s0f1: speed changed to 0 for port enp5s0f1 [ 1675.911259] ixgbe 0000:05:00.1 enp5s0f1: detected SFP+: 6 [ 1676.159087] ixgbe 0000:05:00.1 enp5s0f1: NIC Link is Up 10 Gbps, Flow Control: RX/TX [ 1684.745389] bond0: Invalid MTU 9000 requested, hw max 1500 Bonding Mode: IEEE 802.3ad Dynamic link aggregation Transmit Hash Policy: layer3+4 (1) MII Status: up MII Polling Interval (ms): 0 Up Delay (ms): 0 Down Delay (ms): 0 802.3ad info LACP rate: slow Min links: 0 Aggregator selection policy (ad_select): stable System priority: 65535 System MAC address: 90:e2:ba:15:68:20 Active Aggregator Info: Aggregator ID: 2 Number of ports: 2 Actor Key: 13 Partner Key: 221 Partner Mac Address: 02:1c:73:b2:9a:29 Slave Interface: enp5s0f0 MII Status: up Speed: 10000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:15:68:20 Slave queue ID: 0 Aggregator ID: 2 Actor Churn State: none Partner Churn State: none Actor Churned Count: 0 Partner Churned Count: 0 details actor lacp pdu: system priority: 65535 system mac address: 90:e2:ba:15:68:20 port key: 13 port priority: 255 port number: 1 port state: 61 details partner lacp pdu: system priority: 32768 system mac address: 02:1c:73:b2:9a:29 oper key: 221 port priority: 16000 port number: 373 port state: 61 Slave Interface: enp5s0f1 MII Status: up Speed: 10000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:15:68:21 Slave queue ID: 0 Aggregator ID: 2 Actor Churn State: none Partner Churn State: none Actor Churned Count: 0 Partner Churned Count: 0 details actor lacp pdu: system priority: 65535 system mac address: 90:e2:ba:15:68:20 port key: 13 port priority: 255 port number: 2 port state: 61 details partner lacp pdu: system priority: 32768 system mac address: 02:1c:73:b2:9a:29 oper key: 221 port priority: 17000 port number: 33141 port state: 61 Settings for enp5s0f0: Supported ports: [ FIBRE ] Supported link modes: 1000baseT/Full 10000baseT/Full Supported pause frame use: Symmetric Supports auto-negotiation: Yes Advertised link modes: 1000baseT/Full 10000baseT/Full Advertised pause frame use: Symmetric Advertised auto-negotiation: Yes Speed: 10000Mb/s Duplex: Full Port: FIBRE PHYAD: 0 Transceiver: external Auto-negotiation: on Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes Settings for enp5s0f1: Supported ports: [ FIBRE ] Supported link modes: 1000baseT/Full 10000baseT/Full Supported pause frame use: Symmetric Supports auto-negotiation: Yes Advertised link modes: 1000baseT/Full 10000baseT/Full Advertised pause frame use: Symmetric Advertised auto-negotiation: Yes Speed: 10000Mb/s Duplex: Full Port: FIBRE PHYAD: 0 Transceiver: external Auto-negotiation: on Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes Reply at: https://bugs.launchpad.net/ubuntu/+source/linux-hwe- edge/+bug/1679823/comments/0 ------------------------------------------------------------------------ On 2017-03-06T13:28:00+00:00 jarod wrote: The fix for this has been added to the net tree and is queued up for 4.10-stable. Reply at: https://bugs.launchpad.net/ubuntu/+source/linux-hwe- edge/+bug/1679823/comments/1 ------------------------------------------------------------------------ On 2017-04-25T15:31:06+00:00 dirk wrote: The problems also occurs in 4.8.0-49 in ubuntu: See: https://bugs.launchpad.net/linux/+bug/1679823/comments/6 and https://bugs.launchpad.net/linux/+bug/1679823/comments/7 Reply at: https://bugs.launchpad.net/ubuntu/+source/linux-hwe- edge/+bug/1679823/comments/12 ------------------------------------------------------------------------ On 2023-12-29T09:47:34+00:00 kkimdavenport wrote: We have added the fix to the net tree and it is scheduled for 4.10-stable. https://flappy-bird.co Reply at: https://bugs.launchpad.net/ubuntu/+source/linux-hwe- edge/+bug/1679823/comments/99 ** Changed in: linux Status: Unknown => Confirmed ** Changed in: linux Importance: Unknown => Medium -- You received this bug notification because you are a member of Kernel Packages, which is subscribed to linux-hwe-edge in Ubuntu. https://bugs.launchpad.net/bugs/1679823 Title: bond0: Invalid MTU 9000 requested, hw max 1500 with kernel 4.8 / 4.10 in XENIAL LTS Status in Linux: Confirmed Status in linux package in Ubuntu: Triaged Status in linux-hwe package in Ubuntu: Fix Released Status in linux-hwe-edge package in Ubuntu: Confirmed Status in linux source package in Xenial: Confirmed Status in linux-hwe source package in Xenial: Fix Released Status in linux-hwe-edge source package in Xenial: Confirmed Status in linux source package in Yakkety: Fix Released Status in linux-hwe source package in Yakkety: Fix Committed Status in linux-hwe-edge source package in Yakkety: Fix Committed Status in linux source package in Zesty: In Progress Status in linux-hwe source package in Zesty: Confirmed Status in linux-hwe-edge source package in Zesty: Confirmed Bug description: Since I upgraded the kernel from linux-image-4.8.0-46-generic to linux-image-extra-4.10.0-14-generic I'm facing an issue when I want to change the MTU. It seems to be known bug already fixed: https://bugzilla.kernel.org/show_bug.cgi?id=194763 # ip l sh eno49 2: eno49: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 9000 qdisc mq master bond0 state UP mode DEFAULT group default qlen 1000 link/ether 5c:b9:01:8a:61:e9 brd ff:ff:ff:ff:ff:ff # ip l sh eno50 3: eno50: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 9000 qdisc mq master bond0 state UP mode DEFAULT group default qlen 1000 link/ether 5c:b9:01:8a:61:e9 brd ff:ff:ff:ff:ff:ff # ip l sh bond0 6: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000 link/ether 5c:b9:01:8a:61:e9 brd ff:ff:ff:ff:ff:ff # ip l set mtu 9000 bond0 RTNETLINK answers: Invalid argument root@controller002[SRV][YUL]:~# tail -1 /var/log/syslog Apr 4 19:36:28 controller002 kernel: [ 8869.077853] bond0: Invalid MTU 9000 requested, hw max 1500 # modinfo ixgbe filename: /lib/modules/4.10.0-14-generic/kernel/drivers/net/ethernet/intel/ixgbe/ixgbe.ko version: 4.4.0-k license: GPL description: Intel(R) 10 Gigabit PCI Express Network Driver # modinfo bonding filename: /lib/modules/4.10.0-14-generic/kernel/drivers/net/bonding/bonding.ko author: Thomas Davis, tada...@lbl.gov and many others description: Ethernet Channel Bonding Driver, v3.7.1 version: 3.7.1 To manage notifications about this bug go to: https://bugs.launchpad.net/linux/+bug/1679823/+subscriptions -- Mailing list: https://launchpad.net/~kernel-packages Post to : kernel-packages@lists.launchpad.net Unsubscribe : https://launchpad.net/~kernel-packages More help : https://help.launchpad.net/ListHelp
