Hi Шенцев! On 09/09/13, at 12:52:31 AM you wrote:
> 09.09.2013 00:33, Konstantin Lepikhov пишет: > > А теперь еще раз вывод lspci -nnvv > > Во вложении. > > > (выполнять от рута) > > Ой, Костя, такие вещи разжовываешь участнику ALT Team ... ;) > тут дело не в тим, а что если не от рута, часть параметров lspci не покажет. > > Похоже никто вашей карты не видит, потому что ее pciid неизвестен. Вот > > почему он незвестен будем разбираться. > > А по чему её видит fglrx? > У меня есть подозрение, что модуль radeon у вас заблокирован. Покажите вывод команды # fgrep -ri radeon /etc/modprobe.d Если есть что-то про blacklist (или вообще ничего нет), то уберите эти строки, и добавьте следущее: # fgrep -ir radeon /etc/modprobe.d/ /etc/modprobe.d/radeon-kms.conf:options radeon modeset=1 затем depmod -a && make-initrd && reboot > 00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor > Family DRAM Controller [8086:0100] (rev 09) > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort+ >SERR- <PERR- INTx- > Latency: 0 > Capabilities: [e0] Vendor Specific Information: Len=0c <?> > > 00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation Core > Processor Family PCI Express Root Port [8086:0101] (rev 09) (prog-if 00 > [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 4 bytes > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 > I/O behind bridge: 0000d000-0000dfff > Memory behind bridge: fbe00000-fbefffff > Prefetchable memory behind bridge: 00000000e0000000-00000000efffffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: [88] Subsystem: Gigabyte Technology Co., Ltd Device > [1458:5000] > Capabilities: [80] Power Management version 3 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit- > Address: fee0f00c Data: 4181 > Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00 > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, > L1 <1us > ExtTag- RBE+ FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > MaxPayload 128 bytes, MaxReadReq 128 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- > TransPend- > LnkCap: Port #2, Speed 5GT/s, Width x16, ASPM L0s L1, Latency > L0 <256ns, L1 <4us > ClockPM- Surprise- LLActRep- BwNot+ > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ > DLActive- BWMgmt+ ABWMgmt- > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- > Surprise- > Slot #1, PowerLimit 0.000W; Interlock- NoCompl+ > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- > LinkChg- > Control: AttnInd Unknown, PwrInd Unknown, Power- > Interlock- > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ > Interlock- > Changed: MRL- PresDet+ LinkState- > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- > CRSVisible- > RootCap: CRSVisible- > RootSta: PME ReqID 0000, PMEStatus- PMEPending- > DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR+, > OBFF Not Supported ARIFwd- > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, > OBFF Disabled ARIFwd- > LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- > Transmit Margin: Normal Operating Range, > EnterModifiedCompliance- ComplianceSOS- > Compliance De-emphasis: -6dB > LnkSta2: Current De-emphasis Level: -6dB, > EqualizationComplete-, EqualizationPhase1- > EqualizationPhase2-, EqualizationPhase3-, > LinkEqualizationRequest- > Capabilities: [100 v1] Virtual Channel > Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 > Arb: Fixed- WRR32- WRR64- WRR128- > Ctrl: ArbSelect=Fixed > Status: InProgress- > VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- > Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256- > Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff > Status: NegoPending- InProgress- > Capabilities: [140 v1] Root Complex Link > Desc: PortNumber=02 ComponentID=01 EltType=Config > Link0: Desc: TargetPort=00 TargetComponent=01 AssocRCRB- > LinkType=MemMapped LinkValid+ > Addr: 0000000000009000 > Kernel driver in use: pcieport > > 00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 > Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04) > Subsystem: Gigabyte Technology Co., Ltd Device [1458:1c3a] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin A routed to IRQ 41 > Region 0: Memory at fbfff000 (64-bit, non-prefetchable) [size=16] > Capabilities: [50] Power Management version 3 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [8c] MSI: Enable+ Count=1/1 Maskable- 64bit+ > Address: 00000000fee0f00c Data: 4191 > Kernel driver in use: mei_me > > 00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset > Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 05) (prog-if 20 > [EHCI]) > Subsystem: Gigabyte Technology Co., Ltd Device [1458:5006] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin C routed to IRQ 18 > Region 0: Memory at fbffe000 (32-bit, non-prefetchable) [size=1K] > Capabilities: [50] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [58] Debug port: BAR=1 offset=00a0 > Capabilities: [98] PCI Advanced Features > AFCap: TP+ FLR+ > AFCtrl: FLR- > AFStatus: TP- > Kernel driver in use: ehci-pci > > 00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset > Family High Definition Audio Controller [8086:1c20] (rev 05) > Subsystem: Gigabyte Technology Co., Ltd Device [1458:a002] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 4 bytes > Interrupt: pin A routed to IRQ 42 > Region 0: Memory at fbff8000 (64-bit, non-prefetchable) [size=16K] > Capabilities: [50] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ > Address: 00000000fee0f00c Data: 41c1 > Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00 > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, > L1 <1us > ExtTag- RBE- FLReset+ > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > MaxPayload 128 bytes, MaxReadReq 128 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ > TransPend- > LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency > L0 <64ns, L1 <1us > ClockPM- Surprise- LLActRep- BwNot- > LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- > DLActive- BWMgmt- ABWMgmt- > Capabilities: [100 v1] Virtual Channel > Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 > Arb: Fixed- WRR32- WRR64- WRR128- > Ctrl: ArbSelect=Fixed > Status: InProgress- > VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- > Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- > Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01 > Status: NegoPending- InProgress- > VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- > Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- > Ctrl: Enable+ ID=1 ArbSelect=Fixed TC/VC=02 > Status: NegoPending- InProgress- > Capabilities: [130 v1] Root Complex Link > Desc: PortNumber=0f ComponentID=00 EltType=Config > Link0: Desc: TargetPort=00 TargetComponent=00 AssocRCRB- > LinkType=MemMapped LinkValid+ > Addr: 00000000fed1c000 > Kernel driver in use: snd_hda_intel > > 00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset > Family PCI Express Root Port 1 [8086:1c10] (rev b5) (prog-if 00 [Normal > decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 4 bytes > Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 > I/O behind bridge: 00002000-00002fff > Memory behind bridge: f0000000-f01fffff > Prefetchable memory behind bridge: 00000000f0200000-00000000f03fffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00 > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, > L1 <1us > ExtTag- RBE+ FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > MaxPayload 128 bytes, MaxReadReq 128 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ > TransPend- > LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s, Latency L0 > <1us, L1 <64us > ClockPM- Surprise- LLActRep+ BwNot- > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ > DLActive- BWMgmt- ABWMgmt- > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ > Surprise+ > Slot #16, PowerLimit 10.000W; Interlock- NoCompl+ > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- > LinkChg- > Control: AttnInd Unknown, PwrInd Unknown, Power- > Interlock- > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- > Interlock- > Changed: MRL- PresDet- LinkState- > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- > CRSVisible- > RootCap: CRSVisible- > RootSta: PME ReqID 0000, PMEStatus- PMEPending- > DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, OBFF > Not Supported ARIFwd- > DevCtl2: Completion Timeout: 260ms to 900ms, TimeoutDis-, LTR-, > OBFF Disabled ARIFwd- > LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis- > Transmit Margin: Normal Operating Range, > EnterModifiedCompliance- ComplianceSOS- > Compliance De-emphasis: -6dB > LnkSta2: Current De-emphasis Level: -3.5dB, > EqualizationComplete-, EqualizationPhase1- > EqualizationPhase2-, EqualizationPhase3-, > LinkEqualizationRequest- > Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- > Address: 00000000 Data: 0000 > Capabilities: [90] Subsystem: Gigabyte Technology Co., Ltd Device > [1458:5001] > Capabilities: [a0] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Kernel driver in use: pcieport > > 00:1c.1 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset > Family PCI Express Root Port 2 [8086:1c12] (rev b5) (prog-if 00 [Normal > decode]) > Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 4 bytes > Bus: primary=00, secondary=03, subordinate=04, sec-latency=0 > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort+ <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00 > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, > L1 <1us > ExtTag- RBE+ FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > MaxPayload 128 bytes, MaxReadReq 128 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ > TransPend- > LnkCap: Port #2, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 > <1us, L1 <4us > ClockPM- Surprise- LLActRep+ BwNot- > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ > DLActive+ BWMgmt+ ABWMgmt- > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- > Surprise- > Slot #1, PowerLimit 10.000W; Interlock- NoCompl+ > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- > LinkChg- > Control: AttnInd Unknown, PwrInd Unknown, Power- > Interlock- > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ > Interlock- > Changed: MRL- PresDet- LinkState+ > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- > CRSVisible- > RootCap: CRSVisible- > RootSta: PME ReqID 0000, PMEStatus- PMEPending- > DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, OBFF > Not Supported ARIFwd- > DevCtl2: Completion Timeout: 260ms to 900ms, TimeoutDis-, LTR-, > OBFF Disabled ARIFwd- > LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- > Transmit Margin: Normal Operating Range, > EnterModifiedCompliance- ComplianceSOS- > Compliance De-emphasis: -6dB > LnkSta2: Current De-emphasis Level: -3.5dB, > EqualizationComplete-, EqualizationPhase1- > EqualizationPhase2-, EqualizationPhase3-, > LinkEqualizationRequest- > Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- > Address: 00000000 Data: 0000 > Capabilities: [90] Subsystem: Gigabyte Technology Co., Ltd Device > [1458:5001] > Capabilities: [a0] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Kernel driver in use: pcieport > > 00:1c.4 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset > Family PCI Express Root Port 5 [8086:1c18] (rev b5) (prog-if 00 [Normal > decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 4 bytes > Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 > I/O behind bridge: 0000e000-0000efff > Memory behind bridge: fbd00000-fbdfffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00 > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, > L1 <1us > ExtTag- RBE+ FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > MaxPayload 128 bytes, MaxReadReq 128 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ > TransPend- > LnkCap: Port #5, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 > <512ns, L1 <4us > ClockPM- Surprise- LLActRep+ BwNot- > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ > DLActive+ BWMgmt+ ABWMgmt- > SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- > Surprise- > Slot #4, PowerLimit 10.000W; Interlock- NoCompl+ > SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- > LinkChg- > Control: AttnInd Unknown, PwrInd Unknown, Power- > Interlock- > SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ > Interlock- > Changed: MRL- PresDet- LinkState+ > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- > CRSVisible- > RootCap: CRSVisible- > RootSta: PME ReqID 0000, PMEStatus- PMEPending- > DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, OBFF > Not Supported ARIFwd- > DevCtl2: Completion Timeout: 260ms to 900ms, TimeoutDis-, LTR-, > OBFF Disabled ARIFwd- > LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- > Transmit Margin: Normal Operating Range, > EnterModifiedCompliance- ComplianceSOS- > Compliance De-emphasis: -6dB > LnkSta2: Current De-emphasis Level: -3.5dB, > EqualizationComplete-, EqualizationPhase1- > EqualizationPhase2-, EqualizationPhase3-, > LinkEqualizationRequest- > Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- > Address: 00000000 Data: 0000 > Capabilities: [90] Subsystem: Gigabyte Technology Co., Ltd Device > [1458:5001] > Capabilities: [a0] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Kernel driver in use: pcieport > > 00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset > Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05) (prog-if 20 > [EHCI]) > Subsystem: Gigabyte Technology Co., Ltd Device [1458:5006] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin A routed to IRQ 23 > Region 0: Memory at fbffd000 (32-bit, non-prefetchable) [size=1K] > Capabilities: [50] Power Management version 2 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > PME(D0+,D1-,D2-,D3hot+,D3cold+) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [58] Debug port: BAR=1 offset=00a0 > Capabilities: [98] PCI Advanced Features > AFCap: TP+ FLR+ > AFCtrl: FLR- > AFStatus: TP- > Kernel driver in use: ehci-pci > > 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] > (rev a5) (prog-if 01 [Subtractive decode]) > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Bus: primary=00, secondary=06, subordinate=06, sec-latency=32 > Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort+ <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: [50] Subsystem: Gigabyte Technology Co., Ltd Motherboard > [1458:5000] > > 00:1f.0 ISA bridge [0601]: Intel Corporation H61 Express Chipset Family LPC > Controller [8086:1c5c] (rev 05) > Subsystem: Gigabyte Technology Co., Ltd Device [1458:5001] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Capabilities: [e0] Vendor Specific Information: Len=0c <?> > Kernel driver in use: lpc_ich > > 00:1f.2 IDE interface [0101]: Intel Corporation 6 Series/C200 Series Chipset > Family 4 port SATA IDE Controller [8086:1c00] (rev 05) (prog-if 8f [Master > SecP SecO PriP PriO]) > Subsystem: Gigabyte Technology Co., Ltd Device [1458:b002] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin B routed to IRQ 19 > Region 0: I/O ports at ff00 [size=8] > Region 1: I/O ports at fe00 [size=4] > Region 2: I/O ports at fd00 [size=8] > Region 3: I/O ports at fc00 [size=4] > Region 4: I/O ports at fb00 [size=16] > Region 5: I/O ports at fa00 [size=16] > Capabilities: [70] Power Management version 3 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [b0] PCI Advanced Features > AFCap: TP+ FLR+ > AFCtrl: FLR- > AFStatus: TP- > Kernel driver in use: ata_piix > > 00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family > SMBus Controller [8086:1c22] (rev 05) > Subsystem: Gigabyte Technology Co., Ltd Device [1458:5001] > Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Interrupt: pin C routed to IRQ 18 > Region 0: Memory at fbffc000 (64-bit, non-prefetchable) [size=256] > Region 4: I/O ports at 0500 [size=32] > Kernel driver in use: i801_smbus > > 00:1f.5 IDE interface [0101]: Intel Corporation 6 Series/C200 Series Chipset > Family 2 port SATA IDE Controller [8086:1c08] (rev 05) (prog-if 85 [Master > SecO PriO]) > Subsystem: Gigabyte Technology Co., Ltd Device [1458:b002] > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin B routed to IRQ 19 > Region 0: I/O ports at f800 [size=8] > Region 1: I/O ports at f700 [size=4] > Region 2: I/O ports at f600 [size=8] > Region 3: I/O ports at f500 [size=4] > Region 4: I/O ports at f400 [size=16] > Region 5: I/O ports at f300 [size=16] > Capabilities: [70] Power Management version 3 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [b0] PCI Advanced Features > AFCap: TP+ FLR+ > AFCtrl: FLR- > AFStatus: TP- > Kernel driver in use: ata_piix > > 01:00.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. > [AMD/ATI] Juniper PRO [Radeon HD 6750] [1002:68bf] (prog-if 00 [VGA > controller]) > Subsystem: Hightech Information System Ltd. Device [1787:2014] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 4 bytes > Interrupt: pin A routed to IRQ 10 > Region 0: Memory at e0000000 (64-bit, prefetchable) [size=256M] > Region 2: Memory at fbec0000 (64-bit, non-prefetchable) [size=128K] > Region 4: I/O ports at de00 [size=256] > [virtual] Expansion ROM at fbe00000 [disabled] [size=128K] > Capabilities: [50] Power Management version 3 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00 > DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 > unlimited > ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+ > MaxPayload 128 bytes, MaxReadReq 512 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- > TransPend- > LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency > L0 <64ns, L1 <1us > ClockPM- Surprise- LLActRep- BwNot- > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ > DLActive- BWMgmt- ABWMgmt- > DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, > OBFF Not Supported > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, > OBFF Disabled > LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis- > Transmit Margin: Normal Operating Range, > EnterModifiedCompliance- ComplianceSOS- > Compliance De-emphasis: -6dB > LnkSta2: Current De-emphasis Level: -6dB, > EqualizationComplete-, EqualizationPhase1- > EqualizationPhase2-, EqualizationPhase3-, > LinkEqualizationRequest- > Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+ > Address: 0000000000000000 Data: 0000 > Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 > Len=010 <?> > Capabilities: [150 v1] Advanced Error Reporting > UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- > RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- > CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ > CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ > AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- > > 01:00.1 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI] Juniper > HDMI Audio [Radeon HD 5700 Series] [1002:aa58] > Subsystem: Hightech Information System Ltd. Device [1787:aa58] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 4 bytes > Interrupt: pin B routed to IRQ 43 > Region 0: Memory at fbefc000 (64-bit, non-prefetchable) [size=16K] > Capabilities: [50] Power Management version 3 > Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00 > DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 > unlimited > ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+ > MaxPayload 128 bytes, MaxReadReq 512 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- > TransPend- > LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency > L0 <64ns, L1 <1us > ClockPM- Surprise- LLActRep- BwNot- > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ > DLActive- BWMgmt- ABWMgmt- > DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, > OBFF Not Supported > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, > OBFF Disabled > LnkSta2: Current De-emphasis Level: -6dB, > EqualizationComplete-, EqualizationPhase1- > EqualizationPhase2-, EqualizationPhase3-, > LinkEqualizationRequest- > Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+ > Address: 00000000fee0f00c Data: 41d1 > Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 > Len=010 <?> > Capabilities: [150 v1] Advanced Error Reporting > UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- > RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- > CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ > CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ > AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- > Kernel driver in use: snd_hda_intel > > 03:00.0 PCI bridge [0604]: Integrated Technology Express, Inc. Device > [1283:8892] (rev 30) (prog-if 00 [Normal decode]) > Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 4 bytes > Bus: primary=03, secondary=04, subordinate=04, sec-latency=32 > Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort+ <SERR- <PERR- > BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn- > Capabilities: [70] #00 [0000] > > 05:00.0 Ethernet controller [0200]: Qualcomm Atheros AR8151 v2.0 Gigabit > Ethernet [1969:1083] (rev c0) > Subsystem: Gigabyte Technology Co., Ltd Device [1458:e000] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 4 bytes > Interrupt: pin A routed to IRQ 44 > Region 0: Memory at fbdc0000 (64-bit, non-prefetchable) [size=256K] > Region 2: I/O ports at ef00 [size=128] > Capabilities: [40] Power Management version 3 > Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA > PME(D0+,D1+,D2+,D3hot+,D3cold+) > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- > Capabilities: [48] MSI: Enable+ Count=1/1 Maskable- 64bit+ > Address: 00000000fee0f00c Data: 41e1 > Capabilities: [58] Express (v1) Endpoint, MSI 00 > DevCap: MaxPayload 4096 bytes, PhantFunc 0, Latency L0s > unlimited, L1 unlimited > ExtTag- AttnBtn+ AttnInd+ PwrInd+ RBE+ FLReset- > DevCtl: Report errors: Correctable- Non-Fatal- Fatal- > Unsupported- > RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- > MaxPayload 128 bytes, MaxReadReq 512 bytes > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ > TransPend- > LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s Lpcilib: > sysfs_read_vpd: read failed: Connection timed out > 1, Latency L0 unlimited, L1 unlimited > ClockPM+ Surprise- LLActRep- BwNot- > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- > LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ > DLActive- BWMgmt- ABWMgmt- > Capabilities: [6c] Vital Product Data > Not readable > Capabilities: [100 v1] Advanced Error Reporting > UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- > UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- > UESvrt: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- > RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- > CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- > CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ > AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn- > Capabilities: [180 v1] Device Serial Number ff-a5-02-f2-50-e5-49-ff > Kernel driver in use: atl1c > > _______________________________________________ > Kernels mailing list > [email protected] > https://lists.unsafe.ru/mailman/listinfo/kernels -- WBR et al. _______________________________________________ Kernels mailing list [email protected] https://lists.unsafe.ru/mailman/listinfo/kernels
