Ahh, nice, what's the location of the artifacts now?, I still didn't have a moment to check it, but I plan to sort it out before the end of the week.
--- irc: ajo / mangelajo Miguel Angel Ajo Pelayo +34 636 52 25 69 skype: ajoajoajo On Wed, May 27, 2015 at 2:50 PM, Nick Østergaard <[email protected]> wrote: > Be ware it should point to the artifacts place and not the worspace > itself. (Also much faster than retriving from the workspace, since it is > stored on the master) > Den 27/05/2015 10.27 skrev "Miguel Ángel Ajo" <[email protected]>: > >> Sure, I can do it now that I’m back and “operational” after jet lag >> recovery ;). >> >> I need to point a virtual http server to the jenkins workspace, and set a >> redirection. >> .htaccess doesn’t apply here since I’m not using apache, but the >> equivalent in >> cherokee may be rather simple. >> >> I’ll ping back on this thread when it’s ready during this week. >> >> Miguel Ángel Ajo >> >> On Wednesday, 27 de May de 2015 at 10:20, Melroy van den Berg wrote: >> >> Dear Miguel Angel Ajo Pelayo, >> >> Would you like to create a *new sub-domain*: >> http://docs.kicad-pcb.org >> >> I understood that you're the only appropriate person for this. >> >> This link should refer (without URL changes, eg .htaccess or DNS) to the >> content of the latest build of Jenkins. At that moment the Getting Started >> URL will be: >> http://docs.kicad-pcb.org/Getting_Started_in_KiCad.html >> >> Then my patch will get accepted. >> >> Kind regards, >> Melroy van den Berg >> >> >> 2015-05-18 20:52 GMT+02:00 Nick Østergaard <[email protected]>: >> >> 2015-05-18 18:59 GMT+02:00 Melroy van den Berg <[email protected]>: >> > Hi, >> > >> > It's a good idea to setup an URL like: http://docs.kicad-pcb.org/. >> > I don't know who has webserver / DNS access besides ajo? .htacess is not >> > that hard. >> > >> > You can either use the base_name directly. Or change other parts in the >> > code, so I can use for example: >> > event.GetId() == wxID_BLAH or event.GetMenuItem() == wxMenuItem_BLAH. >> Then >> > you can still use a switch without hashmap. >> > >> > Well it's about how complicated you want the code, for opening the >> online >> > docs. >> >> I simply want to avoid any switch case, by using the base_name directly >> as: >> helpFile = wxString::Format( "https://docs.kicad-pcb.org/%s";, >> GetChars( base_name )); >> >> > Kind regards, >> > Melroy van den Berg >> > >> > >> > >> > 2015-05-18 18:40 GMT+02:00 Nick Østergaard <[email protected]>: >> >> >> >> 2015-05-18 18:35 GMT+02:00 Melroy van den Berg < >> [email protected]>: >> >> > Hi Nick and Blair, >> >> > >> >> > @Nick >> >> > I choose for a separate wxString to explicitly make a difference >> between >> >> > a >> >> > local file & online URL. However, yes you can merge them together >> using >> >> > 1 >> >> > xwString. >> >> > If you want, you can change it to your own taste >> >> > >> >> > @Blair >> >> > Thanks for your reply. The first remark I agree, but the current >> >> > documentation also lacks behind, so it already doesn't match the >> current >> >> > installed KiCad version ;) >> >> > About the second remark, this you can easily solve in the code. >> >> > >> >> > But for now, my patch only ensures that it opens the online >> >> > documentation >> >> > when no doc-package is installed or can be found. >> >> >> >> In my minds it would not be that great to include the patch as is. >> >> Firstly it uses the Jenkins URL directly, which is likely subject to >> >> change when we get the cmake stuff included with the docs. >> >> >> >> What I would like to see is that we get some more generic and nicer >> >> url redirects setup, such as http://docs.kicad-pcb.org/pcbnew. Ajo >> >> has expressed his support on IRC, but is busy at the moment. >> >> >> >> By doing this we could get away of the hashmap stuff and just use the >> >> base_name directly to construct the url. I would like other peoples >> >> opinion on this approach. >> >> >> >> > Hopefully this patch will get delivered soon :)! >> >> > Thx. >> >> > >> >> > Kind regards, >> >> > Melroy van den Berg >> >> > >> >> > 2015-05-18 7:31 GMT+02:00 Nick Østergaard <[email protected]>: >> >> >> >> >> >> 2015-05-18 0:44 GMT+02:00 Melroy van den Berg >> >> >> <[email protected]>: >> >> >> > Hi devs, >> >> >> > >> >> >> > I created a patch which opens the online documentation page in the >> >> >> > web-browser, only when the local help file could not be found. >> >> >> > >> >> >> > This way the user don't get the pop-up message: 'PDF could not be >> >> >> > found'. >> >> >> > Instead they can read the latest successfully build documentation >> >> >> > online >> >> >> > :). >> >> >> > >> >> >> > Off-topic: >> >> >> >> >> >> >> >> It would be nice if online documentation becomes the default. >> >> >> >> This way the users always read the latest version of the >> >> >> >> documentation. >> >> >> > >> >> >> > >> >> >> > See attachment for the patch. >> >> >> >> >> >> Why do you do the: >> >> >> if( !helpFile ) >> >> >> { >> >> >> ... helpURL = ... >> >> >> } >> >> >> else >> >> >> { >> >> >> GetAssociatedDocument( this, helpFile ); >> >> >> if(!helpURL.IsEmpty()) >> >> >> { >> >> >> GetAssociatedDocument( this, helpURL ); >> >> >> } >> >> >> >> >> >> Why not just >> >> >> >> >> >> if( !helpFile ) >> >> >> { >> >> >> ... >> >> >> helpFile = ... >> >> >> } >> >> >> GetAssociatedDocument( this, helpFile ); >> >> >> >> >> >> By that it will just set the helpFile if the helpfile was not found. >> >> >> >> >> >> > Thanks in advance! >> >> >> > >> >> >> > Kind regards, >> >> >> > Melroy van den Berg >> >> > >> >> > >> >> > >> >> > >> >> > _______________________________________________ >> >> > Mailing list: https://launchpad.net/~kicad-developers >> >> > Post to : [email protected] >> >> > Unsubscribe : https://launchpad.net/~kicad-developers >> >> > More help : https://help.launchpad.net/ListHelp >> >> > >> > >> > >> >> >> _______________________________________________ >> Mailing list: https://launchpad.net/~kicad-developers >> Post to : [email protected] >> Unsubscribe : https://launchpad.net/~kicad-developers >> More help : https://help.launchpad.net/ListHelp >> >> >> >> _______________________________________________ >> Mailing list: https://launchpad.net/~kicad-developers >> Post to : [email protected] >> Unsubscribe : https://launchpad.net/~kicad-developers >> More help : https://help.launchpad.net/ListHelp >> >>
_______________________________________________ Mailing list: https://launchpad.net/~kicad-developers Post to : [email protected] Unsubscribe : https://launchpad.net/~kicad-developers More help : https://help.launchpad.net/ListHelp
