On Tue, Jun 09, 2015 at 03:33:56PM -0400, Wayne Stambaugh wrote: > How does this bus connect to another bus without a label that looks > something like A[19..32] on other open ended buses? Unless the bus is > directly connected I believe the label is required.
I said "Imagine the bit going off to the right goes somewhere else." - i.e., it is directly connected. > > FYI. I need to get my eyes checked. If a wire doesn't end on the label > connection point, then open ended wires are shown as unconnected. It > looks the dangling end test is in need of some improvement. Again, see > the video demo. There are examples of both cases. I don't see the problem, can you give me a more specific example? > > On 6/9/2015 3:24 PM, Chris Pavlina wrote: > > No, I just mean things like this: > > > > http://misc.c4757p.com/bus.png > > > > The bus is very frequently drawn past the end of a row of connections to > > emphasize the fact that it is a bus. > > > > (Imagine the bit going off to the right goes somewhere else.) > > > > On Tue, Jun 09, 2015 at 03:17:52PM -0400, Wayne Stambaugh wrote: > >> Yes, but typically in open ended bus use case they have a label attached > >> to them that makes the connection. The same thing can be done with > >> wires which does show the connection status correctly when a wire is > >> open ended but has a label attached to it. The video demo project is a > >> good example of both behaviors. It's not that important but some users > >> may wonder why the difference between wire and bus connections. It's > >> something to think about. > >> > >> On 6/9/2015 2:30 PM, Chris Pavlina wrote: > >>> I'm not sure about that one - it's common to draw buses in a manner that > >>> leaves their ends open. > >>> > >>> On Tue, Jun 09, 2015 at 01:43:56PM -0400, Wayne Stambaugh wrote: > >>>> I've tried this patch and it works as expected. Good work Chris. Does > >>>> anyone have any objections to this patch before I commit it? > >>>> > >>>> One other thing I noticed is the bus wires (and I'm guessing bus entries > >>>> as well) do not have any segment end point connection indicators. It > >>>> would be nice if they supported them as well. > >>>> > >>>> On 6/8/2015 5:38 PM, Chris Pavlina wrote: > >>>>> Hi, > >>>>> > >>>>> I already sent in this patch but as a reply to my existing pin targets > >>>>> thread; I think it may have got lost. This patch enables pin "targets" > >>>>> on bus entries as well, as Wayne suggested, and hides them when the bus > >>>>> entry is connected. > >>>>> > >>>>> -- > >>>>> Chris > >>>>> > >>>>> > >>>>> > >>>>> _______________________________________________ > >>>>> Mailing list: https://launchpad.net/~kicad-developers > >>>>> Post to : kicad-developers@lists.launchpad.net > >>>>> Unsubscribe : https://launchpad.net/~kicad-developers > >>>>> More help : https://help.launchpad.net/ListHelp > >>>>> > >>>> > >>>> _______________________________________________ > >>>> Mailing list: https://launchpad.net/~kicad-developers > >>>> Post to : kicad-developers@lists.launchpad.net > >>>> Unsubscribe : https://launchpad.net/~kicad-developers > >>>> More help : https://help.launchpad.net/ListHelp > >>> > >>> _______________________________________________ > >>> Mailing list: https://launchpad.net/~kicad-developers > >>> Post to : kicad-developers@lists.launchpad.net > >>> Unsubscribe : https://launchpad.net/~kicad-developers > >>> More help : https://help.launchpad.net/ListHelp > >>> > >> > >> _______________________________________________ > >> Mailing list: https://launchpad.net/~kicad-developers > >> Post to : kicad-developers@lists.launchpad.net > >> Unsubscribe : https://launchpad.net/~kicad-developers > >> More help : https://help.launchpad.net/ListHelp > > > > _______________________________________________ > > Mailing list: https://launchpad.net/~kicad-developers > > Post to : kicad-developers@lists.launchpad.net > > Unsubscribe : https://launchpad.net/~kicad-developers > > More help : https://help.launchpad.net/ListHelp > > > > _______________________________________________ > Mailing list: https://launchpad.net/~kicad-developers > Post to : kicad-developers@lists.launchpad.net > Unsubscribe : https://launchpad.net/~kicad-developers > More help : https://help.launchpad.net/ListHelp _______________________________________________ Mailing list: https://launchpad.net/~kicad-developers Post to : kicad-developers@lists.launchpad.net Unsubscribe : https://launchpad.net/~kicad-developers More help : https://help.launchpad.net/ListHelp