Hi Bob! There are no code changes in this RC2 package from the nightlies. I made a new autobuilder for this build, and was looking for testers to make sure the autobuilder seems ok.
It does. Thanks! Adam Wolf Cofounder and Engineer W&L On Fri, Nov 13, 2015 at 11:49 AM, Bob Gustafson <[email protected]> wrote: > Whoops - comments on my previous message only apply to eeschema view. > > The pcbnew view (openGL) will scroll so picture is 1/10 the area of the > window, rather than stopping when whole paper is visible in the window. > > Scrolling and Zooming is jumpy and slow. > > Scrolling requires two finger + shift to go up and down. two finger + > command to go left right (and picture motion is opposite to finger motion) > > Scrolling should be the same as eechema - two finger + shift gives two > dimensional scroll - very intuitive. > > Still needs some work. > > Bob G > > > On 11/13/2015 11:03 AM, Bob Gustafson wrote: > > Wow - lots of reasonable changes to the OSX version: > > Two finger + Shift - trackpad works intuitively like it should (at least > for me) - move fingers left, picture moves left, move fingers up, picture > moves up, and scroll stops when edge of paper is reached. > > Two finger - trackpad zoom works more slowly and smoothly. > > I haven't tested beyond the trackpad motions for now (as these were > blockers for me). > > Thanks much to the whole team - including the OSXers. > > Bob G > > On 11/13/2015 10:01 AM, Adam Wolf wrote: > > Both should work. It was me tweaking things that shouldn't impact the > build, things like Jenkins retries and timeouts and stuff like that. > > On Fri, Nov 13, 2015 at 9:51 AM, Johannes Maibaum < <[email protected]> > [email protected]> wrote: > >> Hi Adam, >> >> > Am 13.11.2015 um 15:32 schrieb Adam Wolf < >> <[email protected]>[email protected]>: >> > >> > Hi folks, >> > >> > I uploaded test packages of kicad and kicad-extras from the RC2 branch >> to the regular nightlies area. If someone else could download them and >> make sure they seem OK before publicizing this, that would be appreciated. >> > >> > http://downloads.kicad-pcb.org/osx/ >> >> In that folder, there two packages each (2x kicad-4.0.0-rc2… and 2x >> kicad-extras-4.0.0-rc2) that, from their names, look to be built from >> identical snapshots, but at different times. >> >> Is their any reason I should check both builds? I’m currently only >> downloading the newer ones… >> >> >> Best, >> >> Johannes >> >> > >> > Thanks! >> > >> > Adam Wolf >> > Cofounder and Engineer >> > W&L >> >> _______________________________________________ >> Mailing list: https://launchpad.net/~kicad-developers >> Post to : [email protected] >> Unsubscribe : https://launchpad.net/~kicad-developers >> More help : https://help.launchpad.net/ListHelp >> > > > > _______________________________________________ > Mailing list: https://launchpad.net/~kicad-developers > Post to : [email protected] > Unsubscribe : https://launchpad.net/~kicad-developers > More help : https://help.launchpad.net/ListHelp > > > > > _______________________________________________ > Mailing list: https://launchpad.net/~kicad-developers > Post to : [email protected] > Unsubscribe : https://launchpad.net/~kicad-developers > More help : https://help.launchpad.net/ListHelp > > > > _______________________________________________ > Mailing list: https://launchpad.net/~kicad-developers > Post to : [email protected] > Unsubscribe : https://launchpad.net/~kicad-developers > More help : https://help.launchpad.net/ListHelp > >
_______________________________________________ Mailing list: https://launchpad.net/~kicad-developers Post to : [email protected] Unsubscribe : https://launchpad.net/~kicad-developers More help : https://help.launchpad.net/ListHelp
