Mike (and Jonas from an earlier post), Thanks for the suggestions.
Jonas....They are definitely different versions with the WinXP version (8/25/08) being "later" than the Fedora 9 (7/9/07)..Is there a way (and is it available) to download a more recent version for FC9? Mike....Your comment about the cr/lfs made me go look at the files. It turns out that the 1 file out of 3 that was giving me problems had cr/lfs in it (extra line between statements). I went in and did a delete, return/enter using gedit to hopefully bring it to FC9 "standards". Unfortunately, the problem persists. I'm open to any other suggestions. I've included below the 1st 20 or so lines of 2 of my .sch files to show you what they look like. The FreqCntr(page 1).sch (at line 18) is the one that fails to load. I can't see anything obvious, but maybe someone else might. Thanks and cheers...Steph ***FreqCntr(page 1).sch EESchema Schematic File Version 2 LIBS:power,device,transistors,conn,linear,regul,74xx,cmos4000,adc-dac,memory,xilinx,special,microcontrollers,dsp,microchip,analog_switches,motorola,texas,intel,audio,interface,digital-audio,philips,display,cypress,siliconi,contrib,valves,.\FreqCntr(page 1).cache EELAYER 23 0 EELAYER END $Descr User 14000 8500 Sheet 1 7 Title "Frequency Counter (Page 1)" Date "17 oct 2006" Rev "1.0" Comp "TWC Technologies" Comment1 "" Comment2 "" Comment3 "" Comment4 "" $EndDescr $Sheet S 5150 6500 1600 750 U 48B746AA (This is line 18..not obvious here because of line wrap) F0 "Mem-Mapped Addrs" 60 F1 "Mem-Mapped Addrs.sch" 60 $EndSheet ***FreqCntr(page 3).sch EESchema Schematic File Version 1 LIBS:power,xilinx,special,siliconi,regul,pspice,philips,o_intel,motorola,microcontrollers,microchip1,microchip,memory,linear,interface,intel,graphic,gennum,elec-unifil,dsp,display,digital-audio,cypress,contrib,connorig,conn,cmos4000,chipcon,brooktre,audio,analog_switches,adc-dac,74xxA,74xx,device,.\FreqCntr(page 3).cache EELAYER 23 0 EELAYER END $Descr A4 11700 8267 Sheet 1 1 Title "FE Lo/Hi A-to-D and Front Panel" Date "14 oct 2006" Rev "1.0" Comp "TWC Technologies" Comment1 "" Comment2 "" Comment3 "" Comment4 "" $EndDescr $Sheet S 1350 1100 2550 1450 F0 "FE HiF A-to-D" 60 (This would be line 18 in this working file) F1 "FE HiF A-to-D.sch" 60 $EndSheet $Sheet S 1350 2950 2550 1450 F0 "FE LoF A-to-D" 60 F1 "FE LoF A-to-D.sch" 60 $EndSheet $Sheet --- In [email protected], [EMAIL PROTECTED] wrote: > > Steph, > > The .pro files I've noticed sometimes have a nasty habit of including full > paths making them not work unless the files are located in exactly the > same path, you might want to check that. > > Also line endings, <lf> on linux vs. <cr><lf> in Windoze perhaps. > > Mike Sharkey > [EMAIL PROTECTED] > www.pikeaero.com > > > Hi all, > > > > I have KiCad running on 2 systems: WinXP and Fedora 9 (tho it's not > > clear the OSes have anything to do with this). I recently brought up > > Fedora 9 and installed KiCad. I then took my project/schematic files > > and moved them (thru a Samba file share to my home directory) to the > > Fedora sys. For 1 particular project I have 3 .pro files. 2 of them > > function fine, the 3rd 1 brings me an error (I assume from the .sch > > file it's trying to load): "EESchema file end_sheet struct error at > > line 18, aborted". I looked at the file and it looks like a "$Sheet" > > command on that line. > > > > This file produces no errors on my WinXP sys and I've tried > > transferring it 3 times thinking I might have lost a bit or 2 along > > the way. On the surface, it looks like the files are a match to this > > point. Anyone have any ideas about this? > > > > Also, while I'm here....I would like to organize these files such > > that my folders have .pro files at the "top", so to speak and my .sch > > and other supporting files in a subfolder. Can I do this (even after > > the fact...files have all been created) or does KiCad assume .pro, > > .sch and the rest of the files reside in the same directory and > > there's no way to alter this? There isn't much "pointer" info in the > > .pro files. > > > > Thanks in advance for any help. > > > > Cheers...Steph > > > > >
