Hi Mahmoud, What is the starting IP that netedit shows for that network? You can change it on command line or in the tui.
It uses this IP as the starting point. However, you make a good point, I should check to see if it lets you use the gateway as an IP which shouldn't be the case. Thanks, Shawn. > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] Behalf Of Mahmoud Hanafi > Sent: Wednesday, February 27, 2008 5:00 PM > To: Users of Kusu > Cc: Users of Kusu; [EMAIL PROTECTED] > Subject: Re: [Kusu-users] compute build error (OCS5.0) > > > What happen here was my admin cluster ip is 192.168.0.2. > (192.168.0.1 is > my gateway). So when this node was added kusu gave it 192.168.0.1 > ipaddress. (bug?) Shouldn't it start counting from up from > 192.168.0.2 , > may there is a config setting i missed.... > > > Mahmoud Hanafi > Sr. System Administrator > CSC HPC COE > Bld. 676 > 2435 Fifth Street > WPAFB, Ohio 45433 > (937) 255-1536 > > > Computer Sciences Corporation > Registered Office: 2100 East Grand Avenue, El Segundo > California 90245, > USA > Registered in USA No: C-489-59 > > -------------------------------------------------------------- > -------------------------------------------------------------- > -------------------------------------------------------------- > ---------------------- > This is a PRIVATE message. If you are not the intended > recipient, please > delete without copying and kindly advise us by e-mail of the > mistake in > delivery. > NOTE: Regardless of content, this e-mail shall not operate to > bind CSC to > any order or other contract unless pursuant to explicit > written agreement > or government initiative expressly permitting the use of > e-mail for such > purpose. > -------------------------------------------------------------- > -------------------------------------------------------------- > -------------------------------------------------------------- > ---------------------- > > > > > Mahmoud Hanafi/DEF/[EMAIL PROTECTED] > Sent by: [EMAIL PROTECTED] > 02/27/2008 12:58 PM > Please respond to > Users of Kusu <[email protected]> > > > To > "Users of Kusu" <[email protected]> > cc > > Subject > [Kusu-users] compute build error (OCS5.0) > > > > > > > When trying to build a compute-rel5 node I get the following error > > Base Class > Failure parsing NII! > System ID: None > Line: 8 > Column: 0 > Message: no element found > > > FYI, I am using vmware test setup > > > Mahmoud Hanafi > Sr. System Administrator > CSC HPC COE > Bld. 676 > 2435 Fifth Street > WPAFB, Ohio 45433 > (937) 255-1536 > > > Computer Sciences Corporation > Registered Office: 2100 East Grand Avenue, El Segundo > California 90245, > USA > Registered in USA No: C-489-59 > > -------------------------------------------------------------- > -------------------------------------------------------------- > -------------------------------------------------------------- > ---------------------- > This is a PRIVATE message. If you are not the intended > recipient, please > delete without copying and kindly advise us by e-mail of the > mistake in > delivery. > NOTE: Regardless of content, this e-mail shall not operate to > bind CSC to > any order or other contract unless pursuant to explicit > written agreement > or government initiative expressly permitting the use of > e-mail for such > purpose. > -------------------------------------------------------------- > -------------------------------------------------------------- > -------------------------------------------------------------- > ---------------------- > _______________________________________________ > Kusu-users mailing list > [email protected] > http://mail.osgdc.org/mailman/listinfo/kusu-users > > _______________________________________________ > Kusu-users mailing list > [email protected] > http://mail.osgdc.org/mailman/listinfo/kusu-users > _______________________________________________ Kusu-users mailing list [email protected] http://mail.osgdc.org/mailman/listinfo/kusu-users
