Finn, No, in my case I've got a TD280, which connects 2 x ISDN2 lines.
I suspect that it should work roughly the same, but I dont know for sure. Paul. Saturday, June 7, 2008, 1:37:25 AM, you wrote: FL> Paul, FL> Thank you for your answer. FL> You are talking about ISDN channels. FL> Do you have the KX-TD290 PRI module installed? FL> (I just what to make sure we are talking about the same system before I FL> start blanking out all the CLIP numbers I have assigned to the 23 FL> channels.) FL> Finn FL> Finn Lassen FL> Deputy CIO FL> Axiom FL> 1805 Drew Street FL> Clearwater, Florida 33765 FL> 727-442-7774 voice FL> 727-442-8344 [EMAIL PROTECTED] FL> On 6 Jun 08 6:03 AM, Paul Drage wrote: Finn, FL> I've set up my system to do what you are asking by setting the CLI FL> values in parameter 623. FL> However, I haven't got any values set up for the channels. It may be FL> that you can only have one set of values? FL> I also found that I couldn't set up arbitrary CLI numbers. I can only FL> send out (on the ISDN channels) numbers that are registered to that FL> ISDN channel by my service provider. Attempting to set any other value FL> sends out the base value for my 10 number ISDN DDI block. FL> Paul. FL> Thursday, June 5, 2008, 6:39:07 PM, you wrote: FL>> No, it's definitely a point of getting my PBX to send the right number. FL>> Using the trunk group selection I can get it to send different numbers. FL>> Now, having the provider send out the right text string when receiving a FL>> number is a different matter. FL>> Finn FL>> Finn Lassen FL>> Deputy CIO FL>> Axiom FL>> 1805 Drew Street FL>> Clearwater, Florida 33765 FL>> 727-442-7774 voice FL>> 727-442-8344 fax FL>> [EMAIL PROTECTED]> www.AxiomInt.comFL> On 5 Jun 08 10:54 AM, brad wrote: FL> This could be an issue at the supplier. I am a 22 year veteran of a LUCENT FL> 5ESS switch, total 40 years in business and there is a billing field that is FL> populated on the PRI form in the switch. Your problem could stem from that. FL> Some companies do populate it, others don't. Brad FL> -----Original Message----- FL> From: [EMAIL PROTECTED] FL> [mailto:[EMAIL PROTECTED] On Behalf Of FL> Finn Lassen FL> Sent: Wednesday, June 04, 2008 11:30 PM FL> To: KXT help List FL> Subject: Re: KX-T: KX-TD1232-6 CLIP FL> KX-TD290, KX-TD1232-6 dual cabinets. FL> We now have several companies sharing the above PBX. FL> I'm trying to find a way to set it up so the outgoing caller ID (CLIP) FL> is controlled by the extension (station) that calls out, rather than the FL> CLIP number associated with the channel that happens to be the next free FL> one when dialing "9" to get an outside line. FL> (I know I can assign each channel to a trunk group and then have the FL> caller pick that by dialing 81, 82, 83, etc. instead of just dialing FL> "9". But than means I have to split the pool of channels up between FL> companies (different CLIPs), and requires that callers dial 81, etc. FL> instead of just "9".) FL> I tried blanking out the CLIP number on the first free channel and FL> dialed out (9) from an extension programmed with a different CLIP FL> number, but the call still showed the main number for the company. Is FL> there some system bit or something else I need to change? FL> Possible at all? FL> Or is the CLIP programmed for an extension only used with ISDN and not FL> PRI lines? FL> Finn Lassen FL> Deputy CIO FL> Axiom FL> 1805 Drew Street FL> Clearwater, Florida 33765 FL> 727-442-7774 voice FL> 727-442-8344 [EMAIL PROTECTED] -- Regards, Paul Drage mailto:[EMAIL PROTECTED] Company Manager The HIVE, 5 Belmont, SHREWSBURY. SY1 1TE Tel: 01743 234970 _________________________________________________________________ KX-T Mailing list --- http://kxthelp.com/ Subscription changes: http://kxthelp.com/mailman/listinfo/kxt
