Christian Benvenuti wrote:
This is one important detail you probably missed:
(Note that in this case the VLAN interface is a L3 interface)
If you assign an IP address to the VLAN interface and you transmit
IP traffic on that interface, than the traffic goes through the VLAN
qdisc config and classification works (*).
> [config cut]
>
When I was doing testing with some trivial setup, I did pretty much the same
thing as in your config (forward note - also checked htb, smaller mtu, vlan
if up and down).
In order:
#vconfig add eth0 11
#ip add add 192.168.20.10/24 dev eth0.11 broad +
#ip li set eth0.11 up
#tc qdisc add dev eth0.11 root handle 1:0 hfsc default 1
#tc class add dev eth0.11 parent 1:0 classid 1:1 hfsc sc rate 10mbit
#tc class add dev eth0.11 parent 1:0 classid 1:21 hfsc sc rate 10mbit
#tc filter add dev eth0.11 parent 1:0 proto ip prio 10 u32 flowid 1:21 \
match ip dst 192.168.20.1
#ip add sh dev eth0.11
12: [EMAIL PROTECTED]: <BROADCAST,MULTICAST,SLAVE,UP,10000> mtu 1500 qdisc hfsc
link/ether 00:0c:f1:da:e9:46 brd ff:ff:ff:ff:ff:ff
inet 192.168.20.10/24 brd 192.168.20.255 scope global eth0.11
#tc -d filter sh dev eth0.11
filter parent 1: protocol ip pref 10 u32
filter parent 1: protocol ip pref 10 u32 fh 800: ht divisor 1
filter parent 1: protocol ip pref 10 u32 fh 800::800 order 2048 key ht 800
bkt 0 flowid 1:21 match c0a81401/ffffffff at 16
#tc -d class sh dev eth0.11
class hfsc 1: root
class hfsc 1:1 parent 1: sc m1 0bit d 0ns m2 10000Kbit
class hfsc 1:21 parent 1: sc m1 0bit d 0ns m2 10000Kbit
... then I did
ping 192.168.20.1
... and ended with
#tc -d -s class sh dev eth0.11
class hfsc 1: root
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
rate 0bit 0pps backlog 0b 0p requeues 0
period 0 level 1
class hfsc 1:1 parent 1: sc m1 0bit d 0ns m2 10000Kbit
Sent 348 bytes 9 pkt (dropped 0, overlimits 0 requeues 0)
rate 0bit 0pps backlog 0b 0p requeues 0
period 9 work 348 bytes rtwork 348 bytes level 0
class hfsc 1:21 parent 1: sc m1 0bit d 0ns m2 10000Kbit
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
rate 0bit 0pps backlog 0b 0p requeues 0
period 0 level 0
#tc -d -s filter sh dev eth0.11
filter parent 1: protocol ip pref 10 u32
filter parent 1: protocol ip pref 10 u32 fh 800: ht divisor 1
filter parent 1: protocol ip pref 10 u32 fh 800::800 order 2048 key ht 800
bkt 0 flowid 1:21 (rule hit 0 success 0)
match c0a81401/ffffffff at 16 (success 0 )
... so I'm probably missing / not seeing something simple, or I don't know.
This setup works for real interface, as well as for bonding. During testing,
real interface is normally working in 192.168.100/24 subnet.
"Moving" from OBSD I'm checking what I can and cannot do under linux, so my
kernel is a bit full atm, with majority of stuff compiled into it.
I'm using clean & patched gentoo here.
_______________________________________________
LARTC mailing list
LARTC@mailman.ds9a.nl
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
