Update of /cvsroot/leaf/src/The_UnNamed_One/apps/dropbear
In directory sc8-pr-cvs6.sourceforge.net:/tmp/cvs-serv15949/apps/dropbear
Added Files:
buildtool.cfg buildtool.mk dropbear-0.50.tar.gz dropbear.conf
dropbear.init options.h
Log Message:
initial import
--- NEW FILE: options.h ---
/* Dropbear SSH
* Copyright (c) 2002,2003 Matt Johnston
* All rights reserved. See LICENSE for the license. */
#ifndef _OPTIONS_H_
#define _OPTIONS_H_
/******************************************************************
* Define compile-time options below - the "#ifndef DROPBEAR_XXX .... #endif"
* parts are to allow for commandline -DDROPBEAR_XXX options etc.
******************************************************************/
#ifndef DROPBEAR_DEFPORT
#define DROPBEAR_DEFPORT "22"
#endif
#ifndef DROPBEAR_DEFADDRESS
/* Listen on all interfaces */
#define DROPBEAR_DEFADDRESS ""
#endif
/* Default hostkey paths - these can be specified on the command line */
#ifndef DSS_PRIV_FILENAME
#define DSS_PRIV_FILENAME "/etc/dropbear/dropbear_dss_host_key"
#endif
#ifndef RSA_PRIV_FILENAME
#define RSA_PRIV_FILENAME "/etc/dropbear/dropbear_rsa_host_key"
#endif
/* Set NON_INETD_MODE if you require daemon functionality (ie Dropbear listens
* on chosen ports and keeps accepting connections. This is the default.
*
* Set INETD_MODE if you want to be able to run Dropbear with inetd (or
* similar), where it will use stdin/stdout for connections, and each process
* lasts for a single connection. Dropbear should be invoked with the -i flag
* for inetd, and can only accept IPv4 connections.
*
* Both of these flags can be defined at once, don't compile without at least
* one of them. */
#define NON_INETD_MODE
/*#define INETD_MODE*/
/* Setting this disables the fast exptmod bignum code. It saves ~5kB, but is
* perhaps 20% slower for pubkey operations (it is probably worth experimenting
* if you want to use this) */
#define NO_FAST_EXPTMOD
/* Set this if you want to use the DROPBEAR_SMALL_CODE option. This can save
several kB in binary size, however will make the symmetrical ciphers (AES, DES
etc) slower (perhaps by 50%). Recommended for most small systems. */
#define DROPBEAR_SMALL_CODE
/* Enable X11 Forwarding - server only */
/*#define ENABLE_X11FWD*/
/* Enable TCP Fowarding */
/* 'Local' is "-L" style (client listening port forwarded via server)
* 'Remote' is "-R" style (server listening port forwarded via client) */
#define ENABLE_CLI_LOCALTCPFWD
#define ENABLE_CLI_REMOTETCPFWD
#define ENABLE_SVR_LOCALTCPFWD
#define ENABLE_SVR_REMOTETCPFWD
/* Enable Authentication Agent Forwarding - server only for now */
#define ENABLE_AGENTFWD
/* Encryption - at least one required.
* RFC Draft requires 3DES and recommends AES128 for interoperability.
* Including multiple keysize variants the same cipher
* (eg AES256 as well as AES128) will result in a minimal size increase.*/
/*#define DROPBEAR_AES128_CBC*/
#define DROPBEAR_3DES_CBC
/*#define DROPBEAR_AES256_CBC*/
/*#define DROPBEAR_BLOWFISH_CBC*/
/*#define DROPBEAR_TWOFISH256_CBC*/
/*#define DROPBEAR_TWOFISH128_CBC*/
/* Message Integrity - at least one required.
* RFC Draft requires sha1 and recommends sha1-96.
* sha1-96 may be of use for slow links, as it has a smaller overhead.
*
* Note: there's no point disabling sha1 to save space, since it's used
* for the random number generator and public-key cryptography anyway.
* Disabling it here will just stop it from being used as the integrity portion
* of the ssh protocol.
*
* These hashes are also used for public key fingerprints in logs.
* If you disable MD5, Dropbear will fall back to SHA1 fingerprints,
* which are not the standard form. */
#define DROPBEAR_SHA1_HMAC
/*#define DROPBEAR_SHA1_96_HMAC*/
/*#define DROPBEAR_MD5_HMAC*/
/* Hostkey/public key algorithms - at least one required, these are used
* for hostkey as well as for verifying signatures with pubkey auth.
* Removing either of these won't save very much space.
* SSH2 RFC Draft requires dss, recommends rsa */
#define DROPBEAR_RSA
#define DROPBEAR_DSS
/* RSA can be vulnerable to timing attacks which use the time required for
* signing to guess the private key. Blinding avoids this attack, though makes
* signing operations slightly slower. */
#define RSA_BLINDING
/* Define DSS_PROTOK to use PuTTY's method of generating the value k for dss,
* rather than just from the random byte source. Undefining this will save you
* ~4k in binary size with static uclibc, but your DSS hostkey could be exposed
* if the random number source isn't good. In general this isn't required */
/* #define DSS_PROTOK */
/* Whether to do reverse DNS lookups. */
#define DO_HOST_LOOKUP
/* Whether to print the message of the day (MOTD). This doesn't add much code
* size */
#define DO_MOTD
/* The MOTD file path */
#ifndef MOTD_FILENAME
#define MOTD_FILENAME "/etc/motd"
#endif
/* Authentication Types - at least one required.
RFC Draft requires pubkey auth, and recommends password */
/* Note: PAM auth is quite simple, and only works for PAM modules which just do
* a simple "Login: " "Password: " (you can edit the strings in svr-authpam.c).
* It's useful for systems like OS X where standard password crypts don't work,
* but there's an interface via a PAM module - don't bother using it otherwise.
* You can't enable both PASSWORD and PAM. */
#define ENABLE_SVR_PASSWORD_AUTH
/*#define ENABLE_SVR_PAM_AUTH */ /* requires ./configure --enable-pam */
#define ENABLE_SVR_PUBKEY_AUTH
#define ENABLE_CLI_PASSWORD_AUTH
#define ENABLE_CLI_PUBKEY_AUTH
#define ENABLE_CLI_INTERACT_AUTH
/* This variable can be used to set a password for client
* authentication on the commandline. Beware of platforms
* that don't protect environment variables of processes etc. Also
* note that it will be provided for all "hidden" client-interactive
* style prompts - if you want something more sophisticated, use
* SSH_ASKPASS instead. Comment out this var to remove this functionality.*/
/*#define DROPBEAR_PASSWORD_ENV "DROPBEAR_PASSWORD"*/
/* Define this (as well as ENABLE_CLI_PASSWORD_AUTH) to allow the use of
* a helper program for the ssh client. The helper program should be
* specified in the SSH_ASKPASS environment variable, and dbclient
* should be run with DISPLAY set and no tty. The program should
* return the password on standard output */
/*#define ENABLE_CLI_ASKPASS_HELPER*/
/* Random device to use - define either DROPBEAR_RANDOM_DEV or
* DROPBEAR_PRNGD_SOCKET.
* DROPBEAR_RANDOM_DEV is recommended on hosts with a good /dev/(u)random,
* otherwise use run prngd (or egd if you want), specifying the socket.
* The device will be queried for a few dozen bytes of seed a couple of times
* per session (or more for very long-lived sessions). */
/* We'll use /dev/urandom by default, since /dev/random is too much hassle.
* If system developers aren't keeping seeds between boots nor getting
* any entropy from somewhere it's their own fault. */
#define DROPBEAR_RANDOM_DEV "/dev/urandom"
/* prngd must be manually set up to produce output */
/*#define DROPBEAR_PRNGD_SOCKET "/var/run/dropbear-rng"*/
/* Specify the number of clients we will allow to be connected but
* not yet authenticated. After this limit, connections are rejected */
/* The first setting is per-IP, to avoid denial of service */
#ifndef MAX_UNAUTH_PER_IP
#define MAX_UNAUTH_PER_IP 5
#endif
/* And then a global limit to avoid chewing memory if connections
* come from many IPs */
#ifndef MAX_UNAUTH_CLIENTS
#define MAX_UNAUTH_CLIENTS 30
#endif
/* Maximum number of failed authentication tries (server option) */
#ifndef MAX_AUTH_TRIES
#define MAX_AUTH_TRIES 10
#endif
/* The default file to store the daemon's process ID, for shutdown
scripts etc. This can be overridden with the -P flag */
#ifndef DROPBEAR_PIDFILE
#define DROPBEAR_PIDFILE "/var/run/dropbear.pid"
#endif
/* The command to invoke for xauth when using X11 forwarding.
* "-q" for quiet */
#ifndef XAUTH_COMMAND
#define XAUTH_COMMAND "/usr/X11R6/bin/xauth -q"
#endif
/* if you want to enable running an sftp server (such as the one included with
* OpenSSH), set the path below. If the path isn't defined, sftp will not
* be enabled */
#ifndef SFTPSERVER_PATH
#define SFTPSERVER_PATH "/usr/libexec/sftp-server"
#endif
/* This is used by the scp binary when used as a client binary. If you're
* not using the Dropbear client, you'll need to change it */
#define _PATH_SSH_PROGRAM "/usr/bin/dbclient"
/* Whether to log commands executed by a client. This only logs the
* (single) command sent to the server, not what a user did in a
* shell/sftp session etc. */
/* #define LOG_COMMANDS */
/* Window size limits. These tend to be a trade-off between memory
usage and network performance: */
/* Size of the network receive window. This amount of memory is allocated
as a per-channel receive buffer. Increasing this value can make a
significant difference to network performance. 24kB was empirically
chosen for a 100mbit ethernet network. The value can be altered at
runtime with the -W argument. */
#define DEFAULT_RECV_WINDOW 24576
/* Maximum size of a received SSH data packet - this _MUST_ be >= 32768
in order to interoperate with other implementations */
#define RECV_MAX_PAYLOAD_LEN 32768
/* Maximum size of a transmitted data packet - this can be any value,
though increasing it may not make a significant difference. */
#define TRANS_MAX_PAYLOAD_LEN 16384
/* Ensure that data is transmitted every KEEPALIVE seconds. This can
be overridden at runtime with -K. 0 disables keepalives */
#define DEFAULT_KEEPALIVE 0
/*******************************************************************
* You shouldn't edit below here unless you know you need to.
*******************************************************************/
#ifndef DROPBEAR_VERSION
#define DROPBEAR_VERSION "0.50"
#endif
#define LOCAL_IDENT "SSH-2.0-dropbear_" DROPBEAR_VERSION
#define PROGNAME "dropbear"
/* Spec recommends after one hour or 1 gigabyte of data. One hour
* is a bit too verbose, so we try 8 hours */
#ifndef KEX_REKEY_TIMEOUT
#define KEX_REKEY_TIMEOUT (3600 * 8)
#endif
#ifndef KEX_REKEY_DATA
#define KEX_REKEY_DATA (1<<30) /* 2^30 == 1GB, this value must be < INT_MAX */
#endif
/* Close connections to clients which haven't authorised after AUTH_TIMEOUT */
#ifndef AUTH_TIMEOUT
#define AUTH_TIMEOUT 300 /* we choose 5 minutes */
#endif
/* Minimum key sizes for DSS and RSA */
#ifndef MIN_DSS_KEYLEN
#define MIN_DSS_KEYLEN 512
#endif
#ifndef MIN_RSA_KEYLEN
#define MIN_RSA_KEYLEN 512
#endif
#define MAX_BANNER_SIZE 2000 /* this is 25*80 chars, any more is foolish */
#define MAX_BANNER_LINES 20 /* How many lines the client will display */
/* the number of NAME=VALUE pairs to malloc for environ, if we don't have
* the clearenv() function */
#define ENV_SIZE 100
#define MAX_CMD_LEN 1024 /* max length of a command */
#define MAX_TERM_LEN 200 /* max length of TERM name */
#define MAX_HOST_LEN 254 /* max hostname len for tcp fwding */
#define MAX_IP_LEN 15 /* strlen("255.255.255.255") == 15 */
#define DROPBEAR_MAX_PORTS 10 /* max number of ports which can be specified,
ipv4 and ipv6
don't count twice */
/* Each port might have at least a v4 and a v6 address */
#define MAX_LISTEN_ADDR (DROPBEAR_MAX_PORTS*3)
#define _PATH_TTY "/dev/tty"
#define _PATH_CP "/bin/cp"
/* success/failure defines */
#define DROPBEAR_SUCCESS 0
#define DROPBEAR_FAILURE -1
/* various algorithm identifiers */
#define DROPBEAR_KEX_DH_GROUP1 0
#define DROPBEAR_SIGNKEY_ANY 0
#define DROPBEAR_SIGNKEY_RSA 1
#define DROPBEAR_SIGNKEY_DSS 2
#define DROPBEAR_SIGNKEY_NONE 3
#define DROPBEAR_COMP_NONE 0
#define DROPBEAR_COMP_ZLIB 1
/* Required for pubkey auth */
#if defined(ENABLE_SVR_PUBKEY_AUTH) || defined(DROPBEAR_CLIENT)
#define DROPBEAR_SIGNKEY_VERIFY
#endif
/* SHA1 is 20 bytes == 160 bits */
#define SHA1_HASH_SIZE 20
/* SHA512 is 64 bytes == 512 bits */
#define SHA512_HASH_SIZE 64
/* MD5 is 16 bytes = 128 bits */
#define MD5_HASH_SIZE 16
/* largest of MD5 and SHA1 */
#define MAX_MAC_LEN SHA1_HASH_SIZE
#define MAX_KEY_LEN 32 /* 256 bits for aes256 etc */
#define MAX_IV_LEN 20 /* must be same as max blocksize,
and >= SHA1_HASH_SIZE */
#define MAX_MAC_KEY 20
#define MAX_NAME_LEN 64 /* maximum length of a protocol name, isn't
explicitly specified for all
protocols (just
for algos) but seems valid */
#define MAX_PROPOSED_ALGO 20
/* size/count limits */
#define MIN_PACKET_LEN 16
#define RECV_MAX_PACKET_LEN (MAX(35000, ((RECV_MAX_PAYLOAD_LEN)+100)))
/* for channel code */
#define TRANS_MAX_WINDOW 500000000 /* 500MB is sufficient, stopping overflow */
#define TRANS_MAX_WIN_INCR 500000000 /* overflow prevention */
#define RECV_WINDOWEXTEND (opts.recv_window / 3) /* We send a "window extend"
every
RECV_WINDOWEXTEND bytes */
#define MAX_RECV_WINDOW (1024*1024) /* 1 MB should be enough */
#define MAX_CHANNELS 100 /* simple mem restriction, includes each tcp/x11
connection, so can't be
_too_ small */
#define MAX_STRING_LEN 1400 /* ~= MAX_PROPOSED_ALGO * MAX_NAME_LEN, also
is the max length
for a password etc */
/* For a 4096 bit DSS key, empirically determined */
#define MAX_PUBKEY_SIZE 1700
/* For a 4096 bit DSS key, empirically determined */
#define MAX_PRIVKEY_SIZE 1700
/* The maximum size of the bignum portion of the kexhash buffer */
/* Sect. 8 of the transport draft, K_S + e + f + K */
#define KEXHASHBUF_MAX_INTS (1700 + 130 + 130 + 130)
#define DROPBEAR_MAX_SOCKS 2 /* IPv4, IPv6 are all we'll get for now. Revisit
in a few years
time.... */
#define DROPBEAR_MAX_CLI_PASS 1024
#define DROPBEAR_MAX_CLI_INTERACT_PROMPTS 80 /* The number of prompts we'll
accept for keyb-interactive
auth */
#if defined(DROPBEAR_AES256_CBC) || defined(DROPBEAR_AES128_CBC)
#define DROPBEAR_AES_CBC
#endif
#if defined(DROPBEAR_TWOFISH256_CBC) || defined(DROPBEAR_TWOFISH128_CBC)
#define DROPBEAR_TWOFISH_CBC
#endif
#ifndef ENABLE_X11FWD
#define DISABLE_X11FWD
#endif
#ifndef ENABLE_AGENTFWD
#define DISABLE_AGENTFWD
#endif
#if defined(ENABLE_CLI_REMOTETCPFWD) || defined(ENABLE_CLI_LOCALTCPFWD)
#define ENABLE_CLI_ANYTCPFWD
#endif
#if defined(ENABLE_CLI_LOCALTCPFWD) || defined(ENABLE_SVR_REMOTETCPFWD)
#define DROPBEAR_TCP_ACCEPT
#endif
#if defined(ENABLE_CLI_REMOTETCPFWD) || defined(ENABLE_CLI_LOCALTCPFWD) || \
defined(ENABLE_SVR_REMOTETCPFWD) || defined(ENABLE_SVR_LOCALTCPFWD) || \
defined(ENABLE_AGENTFWD) || defined(ENABLE_X11FWD)
#define USING_LISTENERS
#endif
#if defined(DROPBEAR_CLIENT) || defined(ENABLE_SVR_PUBKEY_AUTH)
#define DROPBEAR_KEY_LINES /* ie we're using authorized_keys or known_hosts */
#endif
#if defined(ENABLE_SVR_PASSWORD_AUTH) && defined(ENABLE_SVR_PAM_AUTH)
#error "You can't turn on PASSWORD and PAM auth both at once. Fix it in
options.h"
#endif
#if defined(DROPBEAR_RANDOM_DEV) && defined(DROPBEAR_PRNGD_SOCKET)
#error "You can't turn on DROPBEAR_PRNGD_SOCKET and DROPBEAR_RANDOM_DEV at once"
#endif
#if !defined(DROPBEAR_RANDOM_DEV) && !defined(DROPBEAR_PRNGD_SOCKET)
#error "You must choose one of DROPBEAR_PRNGD_SOCKET or DROPBEAR_RANDOM_DEV in
options.h"
#endif
/* We use dropbear_client and dropbear_server as shortcuts to avoid redundant
* code, if we're just compiling as client or server */
#if defined(DROPBEAR_SERVER) && defined(DROPBEAR_CLIENT)
#define IS_DROPBEAR_SERVER (ses.isserver == 1)
#define IS_DROPBEAR_CLIENT (ses.isserver == 0)
#elif defined(DROPBEAR_SERVER)
#define IS_DROPBEAR_SERVER 1
#define IS_DROPBEAR_CLIENT 0
#elif defined(DROPBEAR_CLIENT)
#define IS_DROPBEAR_SERVER 0
#define IS_DROPBEAR_CLIENT 1
#else
#error You must compiled with either DROPBEAR_CLIENT or DROPBEAR_SERVER selected
#endif
#endif /* _OPTIONS_H_ */
--- NEW FILE: dropbear.conf ---
# listening port
DB_PORT=22
# rsa hostkey
DB_RSAFILE=/etc/dropbear/dropbear_rsa_host_key
# dss hostkey
DB_DSSFILE=/etc/dropbear/dropbear_dss_host_key
# optional banner file to display before the user authenticates
DB_BANNER=""
# disable password authentication
#DB_OPTIONS=" -s "
--- NEW FILE: dropbear-0.50.tar.gz ---
(This appears to be a binary file; contents omitted.)
--- NEW FILE: dropbear.init ---
#! /bin/sh
# /etc/init.d/dropbear: start and stop Dropbear ssh2 daemon
# based on the OpenSSH init.d script
RCDLINKS="2,S10 3,S10 4,S10 5,S10 0,K11 1,K11 6,K11"
test -x /usr/sbin/dropbear || exit 0
# default options
DB_PORT=22
DB_RSAFILE=/etc/dropbear/dropbear_rsa_host_key
DB_DSSFILE=/etc/dropbear/dropbear_dss_host_key
DB_BANNER=""
# custom config options
. /etc/default/dropbear
if [ -n "$DB_PORT" ]; then
DB_OPTIONS="$DB_OPTIONS -p $DB_PORT"
fi
if [ -n "$DB_RSAFILE" ]; then
DB_OPTIONS="$DB_OPTIONS -r $DB_RSAFILE"
test -f $DB_RSAFILE || dropbearkey -t rsa -f $DB_RSAFILE
fi
if [ -n "$DB_DSSFILE" ]; then
DB_OPTIONS="$DB_OPTIONS -d $DB_DSSFILE"
test -f $DB_DSSFILE || dropbearkey -t dss -f $DB_DSSFILE
fi
if [ -n "$DB_BANNER" ]; then
DB_OPTIONS="$DB_OPTIONS -b $DB_BANNER"
fi
# Configurable options:
case "$1" in
start)
echo -n "Starting Dropbear Secure Shell server: dropbear"
start-stop-daemon --start --quiet --pidfile /var/run/dropbear.pid
--exec /usr/sbin/dropbear -- $DB_OPTIONS
echo "."
;;
stop)
echo -n "Stopping Dropbear Secure Shell server: dropbear"
start-stop-daemon --stop --quiet --oknodo --pidfile
/var/run/dropbear.pid
echo "."
;;
restart)
echo -n "Restarting Dropbear Secure Shell server: dropbear"
start-stop-daemon --stop --quiet --oknodo --pidfile
/var/run/dropbear.pid
sleep 2
start-stop-daemon --start --quiet --pidfile /var/run/dropbear.pid
--exec /usr/sbin/dropbear -- $DB_OPTIONS
echo "."
;;
*)
echo "Usage: /etc/init.d/dropbear {start|stop|restart}"
exit 1
esac
exit 0
--- NEW FILE: buildtool.mk ---
# makefile for dropbear
include $(MASTERMAKEFILE)
DROPBEAR_DIR:=dropbear-0.50
DROPBEAR_TARGET_DIR:=$(BT_BUILD_DIR)/dropbear
$(DROPBEAR_DIR)/.source:
zcat $(DROPBEAR_SOURCE) | tar -xvf -
touch $(DROPBEAR_DIR)/.source
source: $(DROPBEAR_DIR)/.source
$(DROPBEAR_DIR)/.configured: $(DROPBEAR_DIR)/.source
(cd $(DROPBEAR_DIR) ; CC=$(TARGET_CC) LD=$(TARGET_CC) \
./configure --prefix=/usr --disable-zlib --disable-lastlog )
cp options.h $(DROPBEAR_DIR)
touch $(DROPBEAR_DIR)/.configured
$(DROPBEAR_DIR)/.build: $(DROPBEAR_DIR)/.configured
mkdir -p $(DROPBEAR_TARGET_DIR)
mkdir -p $(DROPBEAR_TARGET_DIR)/etc/init.d
mkdir -p $(DROPBEAR_TARGET_DIR)/etc/default
mkdir -p $(DROPBEAR_TARGET_DIR)/usr/bin
mkdir -p $(DROPBEAR_TARGET_DIR)/usr/sbin
$(MAKE) PROGRAMS="dropbear dropbearkey scp" MULTI=1 STATIC=0
SCPPROGRESS=0 -C $(DROPBEAR_DIR)
-$(BT_STRIP) $(BT_STRIP_BINOPTS) $(DROPBEAR_DIR)/dropbearmulti
cp -a $(DROPBEAR_DIR)/dropbearmulti $(DROPBEAR_TARGET_DIR)/usr/sbin
cp -a dropbear.init $(DROPBEAR_TARGET_DIR)/etc/init.d/dropbear
cp -a dropbear.conf $(DROPBEAR_TARGET_DIR)/etc/default/dropbear
$(MAKE) -C $(DROPBEAR_DIR) clean
$(MAKE) PROGRAMS="dbclient" MULTI=0 STATIC=0 -C $(DROPBEAR_DIR)
-$(BT_STRIP) $(BT_STRIP_BINOPTS) $(DROPBEAR_DIR)/dbclient
cp -a $(DROPBEAR_DIR)/dbclient $(DROPBEAR_TARGET_DIR)/usr/bin
cp -a $(DROPBEAR_TARGET_DIR)/* $(BT_STAGING_DIR)
touch $(DROPBEAR_DIR)/.build
build: $(DROPBEAR_DIR)/.build
clean:
make -C $(DROPBEAR_DIR) clean
rm -rf $(DROPBEAR_TARGET_DIR)
rm $(DROPBEAR_DIR)/.build
rm $(DROPBEAR_DIR)/.configured
srcclean: clean
rm -rf $(DROPBEAR_DIR)
rm $(DROPBEAR_DIR)/.source
--- NEW FILE: buildtool.cfg ---
<File buildtool.mk>
Server = cvs-sourceforge
Revision = HEAD
Directory = dropbear
</File>
<File dropbear-0.50.tar.gz>
Server = cvs-sourceforge
Revision = HEAD
envname = DROPBEAR_SOURCE
Directory = dropbear
</File>
<File options.h>
Server = cvs-sourceforge
Revision = HEAD
Directory = dropbear
</File>
<File dropbear.init>
Server = cvs-sourceforge
Revision = HEAD
Directory = dropbear
</File>
<File dropbear.conf>
Server = cvs-sourceforge
Revision = HEAD
Directory = dropbear
</File>
<Package>
<dropbear>
Version = 0.50
Revision = 3
Help <<EOF
Dropbear SSH 2 server and scp client
Homepage: http://matt.ucc.asn.au/dropbear/dropbear.html
LEAF package by __PACKAGER__, __BUILDDATE__
EOF
<Permissions>
Files = 644
Directories = 755
</Permissions>
<Owner>
Files = root:root
Directories = root:root
</Owner>
<Contents>
<File>
Filename = etc/default/dropbear
Source = etc/default/dropbear
Description = dropbear configuration
Type = conf
Type = local
Type = binary
Permissions = 600
</File>
<File>
Filename = etc/init.d/dropbear
Source = etc/init.d/dropbear
Description = dropbear daemon init file
Type = binary
Permissions = 755
</File>
<File>
Source = usr/sbin/dropbearmulti
Filename = usr/sbin/dropbearmulti
Type = binary
Permissions = 755
</File>
<File>
Target = usr/sbin/dropbearmulti
Filename = usr/bin/scp
Type = link
</File>
<File>
Target = usr/sbin/dropbearmulti
Filename = usr/sbin/dropbear
Type = link
</File>
<File>
Target = usr/sbin/dropbearmulti
Filename = usr/bin/dropbearkey
Type = link
</File>
<File>
Filename = etc/dropbear
Type = directory
Type = local
Permissions = 755
</File>
</Contents>
</dropbear>
<dbclient>
Version = 0.50
Revision = 1
Help <<EOF
Dropbear SSH 2 client
Homepage: http://matt.ucc.asn.au/dropbear/dropbear.html
LEAF package by __PACKAGER__, __BUILDDATE__
EOF
<Permissions>
Files = 644
Directories = 755
</Permissions>
<Owner>
Files = root:root
Directories = root:root
</Owner>
<Contents>
<File>
Source = usr/bin/dbclient
Filename = usr/bin/dbclient
Type = binary
Permissions = 755
</File>
</Contents>
</dbclient>
</Package>
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2008.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
leaf-cvs-commits mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/leaf-cvs-commits
