Hello M, The madwifi drivers are still in beta stage, so it's possible that some debug code is enabled by default. I will take a look anyway.
Eric > Hi Eric, > > > Thanks a lot for suggestions. > > > I started from the original modules.lrp from CD and I copied all needed > modules to that modules.lrp. This time the madwifi modules are loaded OK. > I > did not test the wireless yet but I think it should be fine. > > So for some reason my old /etc/modules has been corrupted. > > > This time I saw 2 lines about "Debugging version" (see below) and not > sure if that's just warning or we are using debugging version > > wlan - Using /lib/modules/./wlan.o wlan: 0.8.6.0 (EXPERIMENTAL) > wlan_acl - Using /lib/modules/./wlan_acl.o wlan: mac acl policy registered > wlan_ccmp - Using /lib/modules/./wlan_ccmp.o wlan_tkip - Using > /lib/modules/./wlan_tkip.o > wlan_wep - Using /lib/modules/./wlan_wep.o wlan_xauth - Using > /lib/modules/./wlan_xauth.o > ath_hal - Using /lib/modules/./ath_hal.o Warning: loading ath_hal will > taint the kernel: non-GPL license ath_hal: 0.9.14.9 (- Proprietary > AR5210 See http://www., AR5211tux.org/lkml/#ex, AR5212port-tainted for, > RF5111 information abo, RF5112ut tainted modul, Rs) > ath_rate_sample - Using /lib/modules/./ath_rate_sample.o ath_rate_sample: > 1.2 > ath_pci - Using /lib/modules/./ath_pci.o ath_pci: 0.9.6.0 (EXPERIMENTAL) > Build date: Aug 6 2005 > Debugging version (IEEE80211) > ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ > ath0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps > ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps > ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps > 24Mbps > 36Mbps 48Mbps 54Mbps > ath0: turboA rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps > ath0: turboG rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps > ath0: H/W encryption support: WEP AES AES_CCM TKIP > ath0: mac 5.9 phy 4.3 radio 3.6 > ath0: Use hw queue 1 for WME_AC_BE traffic > ath0: Use hw queue 0 for WME_AC_BK traffic > ath0: Use hw queue 2 for WME_AC_VI traffic > ath0: Use hw queue 3 for WME_AC_VO traffic > ath0: Use hw queue 8 for CAB traffic > ath0: Use hw queue 9 for beacons > Debugging version (ATH) > ^^^^^^^^^^^^^^^^^^^^^^^^ > > > > > > ----- Original Message ----- > From: "Eric Spakman" <[EMAIL PROTECTED]> > To: "M Lu" <[EMAIL PROTECTED]> > Sent: Wednesday, October 26, 2005 10:51 AM > Subject: Re: [leaf-user] madwifi drivers on Bering 2.3 > > > >> That's a pity, I can't see anything special in your modules file. No >> strange characters or so. You could try to remove the "#" between >> wlan_xauth and ath_hal, but that shouldn't be the problem. >> > > > ------------------------------------------------------- > This SF.Net email is sponsored by the JBoss Inc. > Get Certified Today * Register for a JBoss Training Course > Free Certification Exam for All Training Attendees Through End of 2005 > Visit http://www.jboss.com/services/certification for more information > ------------------------------------------------------------------------ > leaf-user mailing list: [email protected] > https://lists.sourceforge.net/lists/listinfo/leaf-user > Support Request -- http://leaf-project.org/ > > ------------------------------------------------------- This SF.Net email is sponsored by the JBoss Inc. Get Certified Today * Register for a JBoss Training Course Free Certification Exam for All Training Attendees Through End of 2005 Visit http://www.jboss.com/services/certification for more information ------------------------------------------------------------------------ leaf-user mailing list: [email protected] https://lists.sourceforge.net/lists/listinfo/leaf-user Support Request -- http://leaf-project.org/
