Maybe you should also provide a new kernel module in modules.mk for this one...
Acked-by: Álvaro Fernández Rojas <nolt...@gmail.com>
El 02/04/2017 a las 0:34, Rafał Miłecki escribió:
> From: Rafał Miłecki <ra...@milecki.pl>
>
> Signed-off-by: Rafał Miłecki <ra...@milecki.pl>
> ---
> ...cm2835-add-thermal-driver-for-bcm2835-SoC.patch | 365
> +++++++++++++++++++++
> 1 file changed, 365 insertions(+)
> create mode 100644
> target/linux/brcm2708/patches-4.9/081-0001-thermal-bcm2835-add-thermal-driver-for-bcm2835-SoC.patch
>
> diff --git
> a/target/linux/brcm2708/patches-4.9/081-0001-thermal-bcm2835-add-thermal-driver-for-bcm2835-SoC.patch
>
> b/target/linux/brcm2708/patches-4.9/081-0001-thermal-bcm2835-add-thermal-driver-for-bcm2835-SoC.patch
> new file mode 100644
> index 0000000000..a11c542913
> --- /dev/null
> +++
> b/target/linux/brcm2708/patches-4.9/081-0001-thermal-bcm2835-add-thermal-driver-for-bcm2835-SoC.patch
> @@ -0,0 +1,365 @@
> +From bcb7dd9ef206f7d646ed8dac6fe7772083714253 Mon Sep 17 00:00:00 2001
> +From: Stefan Wahren <stefan.wah...@i2se.com>
> +Date: Fri, 31 Mar 2017 20:03:06 +0000
> +Subject: [PATCH] thermal: bcm2835: add thermal driver for bcm2835 SoC
> +MIME-Version: 1.0
> +Content-Type: text/plain; charset=UTF-8
> +Content-Transfer-Encoding: 8bit
> +
> +Add basic thermal driver for bcm2835 SoC.
> +
> +This driver currently make sure that tsense HW block is set up
> +correctly.
> +
> +Tested-by: Rafał Miłecki <ra...@milecki.pl>
> +Signed-off-by: Martin Sperl <ker...@martin.sperl.org>
> +Signed-off-by: Stefan Wahren <stefan.wah...@i2se.com>
> +Acked-by: Eric Anholt <e...@anholt.net>
> +Acked-by: Eduardo Valentin <edubez...@gmail.com>
> +Signed-off-by: Eduardo Valentin <edubez...@gmail.com>
> +---
> + drivers/thermal/Kconfig | 8 +
> + drivers/thermal/Makefile | 1 +
> + drivers/thermal/bcm2835_thermal.c | 314
> ++++++++++++++++++++++++++++++++++++++
> + 3 files changed, 323 insertions(+)
> + create mode 100644 drivers/thermal/bcm2835_thermal.c
> +
> +--- a/drivers/thermal/Kconfig
> ++++ b/drivers/thermal/Kconfig
> +@@ -434,4 +434,12 @@ depends on (ARCH_QCOM && OF) || COMPILE_
> + source "drivers/thermal/qcom/Kconfig"
> + endmenu
> +
> ++config BCM2835_THERMAL
> ++ tristate "Thermal sensors on bcm2835 SoC"
> ++ depends on ARCH_BCM2835 || COMPILE_TEST
> ++ depends on HAS_IOMEM
> ++ depends on THERMAL_OF
> ++ help
> ++ Support for thermal sensors on Broadcom bcm2835 SoCs.
> ++
> + endif
> +--- a/drivers/thermal/Makefile
> ++++ b/drivers/thermal/Makefile
> +@@ -55,3 +55,4 @@ obj-$(CONFIG_TEGRA_SOCTHERM) += tegra/
> + obj-$(CONFIG_HISI_THERMAL) += hisi_thermal.o
> + obj-$(CONFIG_MTK_THERMAL) += mtk_thermal.o
> + obj-$(CONFIG_GENERIC_ADC_THERMAL) += thermal-generic-adc.o
> ++obj-$(CONFIG_BCM2835_THERMAL) += bcm2835_thermal.o
> +--- /dev/null
> ++++ b/drivers/thermal/bcm2835_thermal.c
> +@@ -0,0 +1,314 @@
> ++/*
> ++ * Driver for Broadcom BCM2835 SoC temperature sensor
> ++ *
> ++ * Copyright (C) 2016 Martin Sperl
> ++ *
> ++ * This program is free software; you can redistribute it and/or modify
> ++ * it under the terms of the GNU General Public License as published by
> ++ * the Free Software Foundation; either version 2 of the License, or
> ++ * (at your option) any later version.
> ++ *
> ++ * This program is distributed in the hope that it will be useful,
> ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
> ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> ++ * GNU General Public License for more details.
> ++ */
> ++
> ++#include <linux/clk.h>
> ++#include <linux/debugfs.h>
> ++#include <linux/device.h>
> ++#include <linux/err.h>
> ++#include <linux/io.h>
> ++#include <linux/kernel.h>
> ++#include <linux/module.h>
> ++#include <linux/of.h>
> ++#include <linux/of_address.h>
> ++#include <linux/of_device.h>
> ++#include <linux/platform_device.h>
> ++#include <linux/thermal.h>
> ++
> ++#define BCM2835_TS_TSENSCTL 0x00
> ++#define BCM2835_TS_TSENSSTAT 0x04
> ++
> ++#define BCM2835_TS_TSENSCTL_PRWDW BIT(0)
> ++#define BCM2835_TS_TSENSCTL_RSTB BIT(1)
> ++
> ++/*
> ++ * bandgap reference voltage in 6 mV increments
> ++ * 000b = 1178 mV, 001b = 1184 mV, ... 111b = 1220 mV
> ++ */
> ++#define BCM2835_TS_TSENSCTL_CTRL_BITS 3
> ++#define BCM2835_TS_TSENSCTL_CTRL_SHIFT 2
> ++#define BCM2835_TS_TSENSCTL_CTRL_MASK \
> ++ GENMASK(BCM2835_TS_TSENSCTL_CTRL_BITS + \
> ++ BCM2835_TS_TSENSCTL_CTRL_SHIFT - 1, \
> ++ BCM2835_TS_TSENSCTL_CTRL_SHIFT)
> ++#define BCM2835_TS_TSENSCTL_CTRL_DEFAULT 1
> ++#define BCM2835_TS_TSENSCTL_EN_INT BIT(5)
> ++#define BCM2835_TS_TSENSCTL_DIRECT BIT(6)
> ++#define BCM2835_TS_TSENSCTL_CLR_INT BIT(7)
> ++#define BCM2835_TS_TSENSCTL_THOLD_SHIFT 8
> ++#define BCM2835_TS_TSENSCTL_THOLD_BITS 10
> ++#define BCM2835_TS_TSENSCTL_THOLD_MASK \
> ++ GENMASK(BCM2835_TS_TSENSCTL_THOLD_BITS + \
> ++ BCM2835_TS_TSENSCTL_THOLD_SHIFT - 1, \
> ++ BCM2835_TS_TSENSCTL_THOLD_SHIFT)
> ++/*
> ++ * time how long the block to be asserted in reset
> ++ * which based on a clock counter (TSENS clock assumed)
> ++ */
> ++#define BCM2835_TS_TSENSCTL_RSTDELAY_SHIFT 18
> ++#define BCM2835_TS_TSENSCTL_RSTDELAY_BITS 8
> ++#define BCM2835_TS_TSENSCTL_REGULEN BIT(26)
> ++
> ++#define BCM2835_TS_TSENSSTAT_DATA_BITS 10
> ++#define BCM2835_TS_TSENSSTAT_DATA_SHIFT 0
> ++#define BCM2835_TS_TSENSSTAT_DATA_MASK \
> ++ GENMASK(BCM2835_TS_TSENSSTAT_DATA_BITS + \
> ++ BCM2835_TS_TSENSSTAT_DATA_SHIFT - 1, \
> ++ BCM2835_TS_TSENSSTAT_DATA_SHIFT)
> ++#define BCM2835_TS_TSENSSTAT_VALID BIT(10)
> ++#define BCM2835_TS_TSENSSTAT_INTERRUPT BIT(11)
> ++
> ++struct bcm2835_thermal_data {
> ++ struct thermal_zone_device *tz;
> ++ void __iomem *regs;
> ++ struct clk *clk;
> ++ struct dentry *debugfsdir;
> ++};
> ++
> ++static int bcm2835_thermal_adc2temp(u32 adc, int offset, int slope)
> ++{
> ++ return offset + slope * adc;
> ++}
> ++
> ++static int bcm2835_thermal_temp2adc(int temp, int offset, int slope)
> ++{
> ++ temp -= offset;
> ++ temp /= slope;
> ++
> ++ if (temp < 0)
> ++ temp = 0;
> ++ if (temp >= BIT(BCM2835_TS_TSENSSTAT_DATA_BITS))
> ++ temp = BIT(BCM2835_TS_TSENSSTAT_DATA_BITS) - 1;
> ++
> ++ return temp;
> ++}
> ++
> ++static int bcm2835_thermal_get_temp(void *d, int *temp)
> ++{
> ++ struct bcm2835_thermal_data *data = d;
> ++ u32 val = readl(data->regs + BCM2835_TS_TSENSSTAT);
> ++
> ++ if (!(val & BCM2835_TS_TSENSSTAT_VALID))
> ++ return -EIO;
> ++
> ++ val &= BCM2835_TS_TSENSSTAT_DATA_MASK;
> ++
> ++ *temp = bcm2835_thermal_adc2temp(
> ++ val,
> ++ thermal_zone_get_offset(data->tz),
> ++ thermal_zone_get_slope(data->tz));
> ++
> ++ return 0;
> ++}
> ++
> ++static const struct debugfs_reg32 bcm2835_thermal_regs[] = {
> ++ {
> ++ .name = "ctl",
> ++ .offset = 0
> ++ },
> ++ {
> ++ .name = "stat",
> ++ .offset = 4
> ++ }
> ++};
> ++
> ++static void bcm2835_thermal_debugfs(struct platform_device *pdev)
> ++{
> ++ struct thermal_zone_device *tz = platform_get_drvdata(pdev);
> ++ struct bcm2835_thermal_data *data = tz->devdata;
> ++ struct debugfs_regset32 *regset;
> ++
> ++ data->debugfsdir = debugfs_create_dir("bcm2835_thermal", NULL);
> ++ if (!data->debugfsdir)
> ++ return;
> ++
> ++ regset = devm_kzalloc(&pdev->dev, sizeof(*regset), GFP_KERNEL);
> ++ if (!regset)
> ++ return;
> ++
> ++ regset->regs = bcm2835_thermal_regs;
> ++ regset->nregs = ARRAY_SIZE(bcm2835_thermal_regs);
> ++ regset->base = data->regs;
> ++
> ++ debugfs_create_regset32("regset", 0444, data->debugfsdir, regset);
> ++}
> ++
> ++static struct thermal_zone_of_device_ops bcm2835_thermal_ops = {
> ++ .get_temp = bcm2835_thermal_get_temp,
> ++};
> ++
> ++/*
> ++ * Note: as per Raspberry Foundation FAQ
> ++ * (https://www.raspberrypi.org/help/faqs/#performanceOperatingTemperature)
> ++ * the recommended temperature range for the SoC -40C to +85C
> ++ * so the trip limit is set to 80C.
> ++ * this applies to all the BCM283X SoC
> ++ */
> ++
> ++static const struct of_device_id bcm2835_thermal_of_match_table[] = {
> ++ {
> ++ .compatible = "brcm,bcm2835-thermal",
> ++ },
> ++ {
> ++ .compatible = "brcm,bcm2836-thermal",
> ++ },
> ++ {
> ++ .compatible = "brcm,bcm2837-thermal",
> ++ },
> ++ {},
> ++};
> ++MODULE_DEVICE_TABLE(of, bcm2835_thermal_of_match_table);
> ++
> ++static int bcm2835_thermal_probe(struct platform_device *pdev)
> ++{
> ++ const struct of_device_id *match;
> ++ struct thermal_zone_device *tz;
> ++ struct bcm2835_thermal_data *data;
> ++ struct resource *res;
> ++ int err = 0;
> ++ u32 val;
> ++ unsigned long rate;
> ++
> ++ data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
> ++ if (!data)
> ++ return -ENOMEM;
> ++
> ++ match = of_match_device(bcm2835_thermal_of_match_table,
> ++ &pdev->dev);
> ++ if (!match)
> ++ return -EINVAL;
> ++
> ++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> ++ data->regs = devm_ioremap_resource(&pdev->dev, res);
> ++ if (IS_ERR(data->regs)) {
> ++ err = PTR_ERR(data->regs);
> ++ dev_err(&pdev->dev, "Could not get registers: %d\n", err);
> ++ return err;
> ++ }
> ++
> ++ data->clk = devm_clk_get(&pdev->dev, NULL);
> ++ if (IS_ERR(data->clk)) {
> ++ err = PTR_ERR(data->clk);
> ++ if (err != -EPROBE_DEFER)
> ++ dev_err(&pdev->dev, "Could not get clk: %d\n", err);
> ++ return err;
> ++ }
> ++
> ++ err = clk_prepare_enable(data->clk);
> ++ if (err)
> ++ return err;
> ++
> ++ rate = clk_get_rate(data->clk);
> ++ if ((rate < 1920000) || (rate > 5000000))
> ++ dev_warn(&pdev->dev,
> ++ "Clock %pCn running at %pCr Hz is outside of the
> recommended range: 1.92 to 5MHz\n",
> ++ data->clk, data->clk);
> ++
> ++ /* register of thermal sensor and get info from DT */
> ++ tz = thermal_zone_of_sensor_register(&pdev->dev, 0, data,
> ++ &bcm2835_thermal_ops);
> ++ if (IS_ERR(tz)) {
> ++ err = PTR_ERR(tz);
> ++ dev_err(&pdev->dev,
> ++ "Failed to register the thermal device: %d\n",
> ++ err);
> ++ goto err_clk;
> ++ }
> ++
> ++ /*
> ++ * right now the FW does set up the HW-block, so we are not
> ++ * touching the configuration registers.
> ++ * But if the HW is not enabled, then set it up
> ++ * using "sane" values used by the firmware right now.
> ++ */
> ++ val = readl(data->regs + BCM2835_TS_TSENSCTL);
> ++ if (!(val & BCM2835_TS_TSENSCTL_RSTB)) {
> ++ int trip_temp, offset, slope;
> ++
> ++ slope = thermal_zone_get_slope(tz);
> ++ offset = thermal_zone_get_offset(tz);
> ++ /*
> ++ * For now we deal only with critical, otherwise
> ++ * would need to iterate
> ++ */
> ++ err = tz->ops->get_trip_temp(tz, 0, &trip_temp);
> ++ if (err < 0) {
> ++ err = PTR_ERR(tz);
> ++ dev_err(&pdev->dev,
> ++ "Not able to read trip_temp: %d\n",
> ++ err);
> ++ goto err_tz;
> ++ }
> ++
> ++ /* set bandgap reference voltage and enable voltage regulator */
> ++ val = (BCM2835_TS_TSENSCTL_CTRL_DEFAULT <<
> ++ BCM2835_TS_TSENSCTL_CTRL_SHIFT) |
> ++ BCM2835_TS_TSENSCTL_REGULEN;
> ++
> ++ /* use the recommended reset duration */
> ++ val |= (0xFE << BCM2835_TS_TSENSCTL_RSTDELAY_SHIFT);
> ++
> ++ /* trip_adc value from info */
> ++ val |= bcm2835_thermal_temp2adc(trip_temp,
> ++ offset,
> ++ slope)
> ++ << BCM2835_TS_TSENSCTL_THOLD_SHIFT;
> ++
> ++ /* write the value back to the register as 2 steps */
> ++ writel(val, data->regs + BCM2835_TS_TSENSCTL);
> ++ val |= BCM2835_TS_TSENSCTL_RSTB;
> ++ writel(val, data->regs + BCM2835_TS_TSENSCTL);
> ++ }
> ++
> ++ data->tz = tz;
> ++
> ++ platform_set_drvdata(pdev, tz);
> ++
> ++ bcm2835_thermal_debugfs(pdev);
> ++
> ++ return 0;
> ++err_tz:
> ++ thermal_zone_of_sensor_unregister(&pdev->dev, tz);
> ++err_clk:
> ++ clk_disable_unprepare(data->clk);
> ++
> ++ return err;
> ++}
> ++
> ++static int bcm2835_thermal_remove(struct platform_device *pdev)
> ++{
> ++ struct thermal_zone_device *tz = platform_get_drvdata(pdev);
> ++ struct bcm2835_thermal_data *data = tz->devdata;
> ++
> ++ debugfs_remove_recursive(data->debugfsdir);
> ++ thermal_zone_of_sensor_unregister(&pdev->dev, tz);
> ++ clk_disable_unprepare(data->clk);
> ++
> ++ return 0;
> ++}
> ++
> ++static struct platform_driver bcm2835_thermal_driver = {
> ++ .probe = bcm2835_thermal_probe,
> ++ .remove = bcm2835_thermal_remove,
> ++ .driver = {
> ++ .name = "bcm2835_thermal",
> ++ .of_match_table = bcm2835_thermal_of_match_table,
> ++ },
> ++};
> ++module_platform_driver(bcm2835_thermal_driver);
> ++
> ++MODULE_AUTHOR("Martin Sperl");
> ++MODULE_DESCRIPTION("Thermal driver for bcm2835 chip");
> ++MODULE_LICENSE("GPL");
>
_______________________________________________
Lede-dev mailing list
Lede-dev@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/lede-dev
