This patch adds supports for the GL-inet GL-MT300N-V2.

Specification:
- SoC: MediaTek MT7628AN
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR
- Ethernet: 1 x WAN (100 Mbps) and 1 x LAN (100 Mbps)
- USB: 1 x USB 2.0 port
- Button: 1 x switch button, 1 x reset button
- LED: 3 x LEDS (system power led is not GPIO controller)
- UART: 1 x UART on PCB (JP1: 3.3V, RX, TX, GND)

Installation through Luci:
- The original firmware is LEDE, so both LuCI or sysupgrade can be used.
- Do not keep settings, for sysupgrade please use the -n option.

Installation through bootloader webserver:
- Plug power and hold reset button until red LED blink to bright.
- Install sysupgrade image using web interface on 192.168.1.1.

Signed-off-by: kyson Lok <kyson...@gmail.com>
---
 target/linux/ramips/base-files/etc/board.d/01_leds |   3 +
 .../linux/ramips/base-files/etc/board.d/02_network |   4 +
 target/linux/ramips/base-files/etc/diag.sh         |   3 +
 target/linux/ramips/base-files/lib/ramips.sh       |   3 +
 .../ramips/base-files/lib/upgrade/platform.sh      |   1 +
 target/linux/ramips/dts/GL-MT300N-V2.dts           | 133 +++++++++++++++++++++
 target/linux/ramips/image/mt7628.mk                |   8 ++
 7 files changed, 155 insertions(+)
 create mode 100644 target/linux/ramips/dts/GL-MT300N-V2.dts

diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds 
b/target/linux/ramips/base-files/etc/board.d/01_leds
index 52542ec..6c95a92 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -189,6 +189,9 @@ gl-mt300n|\
 gl-mt750)
        set_wifi_led "$board:wlan"
        ;;
+gl-mt300n-v2)
+       set_wifi_led "$board:red:wlan"
+       ;;
 hc5661|\
 hc5661a)
        ucidef_set_led_default "system" "system" "$board:blue:system" "1"
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network 
b/target/linux/ramips/base-files/etc/board.d/02_network
index 80a3bc2..741e702 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -175,6 +175,10 @@ ramips_setup_interfaces()
                ucidef_add_switch "switch0" \
                        "1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "6@eth0"
                ;;
+       gl-mt300n-v2)
+               ucidef_add_switch "switch0" \
+                       "1:lan" "0:wan" "6@eth0"
+               ;;
        awapn2403)
                ucidef_add_switch "switch0" \
                        "0:lan" "1:wan" "6@eth0"
diff --git a/target/linux/ramips/base-files/etc/diag.sh 
b/target/linux/ramips/base-files/etc/diag.sh
index 461f46c..e051dfd 100644
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -164,6 +164,9 @@ get_status_led() {
        miwifi-nano)
                status_led="$board:blue:status"
                ;;
+       gl-mt300n-v2)
+               status_led="$board:red:wlan"
+               ;;
        m4-4M|\
        m4-8M)
                status_led="m4:blue:status"
diff --git a/target/linux/ramips/base-files/lib/ramips.sh 
b/target/linux/ramips/base-files/lib/ramips.sh
index 87cb7ff..3a8a3f6 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -217,6 +217,9 @@ ramips_board_detect() {
        *"GL-MT750")
                name="gl-mt750"
                ;;
+       *"GL-MT300N-V2")
+               name="gl-mt300n-v2"
+               ;;
        *"HC5661")
                name="hc5661"
                ;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh 
b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index adad8da..c8c3d38 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -65,6 +65,7 @@ platform_check_image() {
        gl-mt300a|\
        gl-mt300n|\
        gl-mt750|\
+       gl-mt300n-v2|\
        hc5*61|\
        hc5661a|\
        hg255d|\
diff --git a/target/linux/ramips/dts/GL-MT300N-V2.dts 
b/target/linux/ramips/dts/GL-MT300N-V2.dts
new file mode 100644
index 0000000..e40c4cf
--- /dev/null
+++ b/target/linux/ramips/dts/GL-MT300N-V2.dts
@@ -0,0 +1,133 @@
+/dts-v1/;
+
+#include "mt7628an.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/{
+       compatible = "gl-inet,gl-mt300n-v2", "ralink,mt7620an-soc";
+       model = "GL-MT300N-V2";
+
+       chosen {
+               bootargs = "console=ttyS0,115200";
+       };
+
+       memory@0 {
+               device_type = "memory";
+               reg = <0x0 0x8000000>;
+       };
+
+       gpio-leds {
+               compatible = "gpio-leds";
+
+               wan {
+                       label = "gl-mt300n-v2:blue:wan";
+                       gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+               };
+
+               wlan {
+                       label = "gl-mt300n-v2:red:wlan";
+                       gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+               };
+       };
+
+       gpio-keys {
+               compatible = "gpio-keys-polled";
+               #address-cells = <1>;
+               #size-cells = <0>;
+               poll-interval = <20>;
+
+               reset {
+                       label = "reset";
+                       gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RESTART>;
+               };
+
+               BTN_0 {
+                       label = "BTN_0";
+                       gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
+                       linux,code = <BTN_0>;
+               };
+
+               BTN_1 {
+                       label = "BTN_1";
+                       gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+                       linux,code = <BTN_1>;
+               };
+       };
+
+       gpio_export {
+               compatible = "gpio-export";
+               #size-cells = <0>;
+
+               usb {
+                       gpio-export,name = "usb";
+                       gpio-export,output = <1>;
+                       gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
+               };
+       };
+
+};
+
+&pinctrl {
+       state_default: pinctrl0 {
+               gpio {
+                       ralink,group = "wdt", "gpio", "wled_an", "p0led_an", 
"i2s";
+                       ralink,function = "gpio";
+               };
+       };
+};
+
+&ethernet {
+       mtd-mac-address = <&factory 0x4000>;
+};
+
+&wmac {
+       status = "okay";
+       ralink,mtd-eeprom = <&factory 0x0>;
+};
+
+&spi0 {
+       status = "okay";
+
+       m25p80@0 {
+               #address-cells = <1>;
+               #size-cells = <1>;
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <10000000>;
+               m25p,chunked-io = <32>;
+
+               partition@0 {
+                       label = "u-boot";
+                       reg = <0x0 0x30000>;
+                       read-only;
+               };
+
+               partition@30000 {
+                       label = "u-boot-env";
+                       reg = <0x30000 0x10000>;
+                       read-only;
+               };
+
+               factory: partition@40000 {
+                        label = "factory";
+                        reg = <0x40000 0x10000>;
+                        read-only;
+               };
+
+               partition@50000 {
+                        label = "firmware";
+                        reg = <0x50000 0xfb0000>;
+               };
+       };
+};
+
+&ehci {
+       status = "okay";
+};
+
+&ohci {
+       status = "okay";
+};
diff --git a/target/linux/ramips/image/mt7628.mk 
b/target/linux/ramips/image/mt7628.mk
index 6bb04ea..5396115 100644
--- a/target/linux/ramips/image/mt7628.mk
+++ b/target/linux/ramips/image/mt7628.mk
@@ -26,6 +26,14 @@ define Device/miwifi-nano
 endef
 TARGET_DEVICES += miwifi-nano
 
+define Device/gl-mt300n-v2
+  DTS := GL-MT300N-V2
+  IMAGE_SIZE := $(ralink_default_fw_size_16M)
+  DEVICE_TITLE := GL-iNet GL-MT300N-V2
+  DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci
+endef
+TARGET_DEVICES += gl-mt300n-v2
+
 define Device/vocore2
   DTS := VOCORE2
   IMAGE_SIZE := $(ralink_default_fw_size_16M)
-- 
1.9.1


_______________________________________________
Lede-dev mailing list
Lede-dev@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/lede-dev

Reply via email to