How would a brass split nut go i would try that if it was me

 

Bill

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Tim Krause
Sent: Friday, 4 August 2017 4:37 AM
To: Legacy Ornamental Mills
Subject: Re: Make a "Split Nut"

 

HDPE is a little soft.  Over on another machinist form that I'm on people have 
heated a lead screw and pressed acetal  (delrin) around the screw to form 
threads.  It takes multiple heating attempts and practice.

Sent from BlueMail <http://www.bluemail.me/r?b=10215>  

On Aug 3, 2017, at 9:23 AM, MWF <mwfos...@earthlink.net> wrote:

Hello all,
I am not sure how well a split nut made from HDPE will hold up - but here is my 
2-cents' worth:
HDPE (Look on bottom of plastic jugs, bottles, etc for the Recycle symbol w/the 
#2) is the only plastic that I know of that we can "re-purpose" at home.
Do an Internet/BING search for this - you'll be amazed.

I find that the plastic Folgers and Maxwell House coffee canisters are labeled 
#2 - as are most milk jugs.  The two coffee brands yield red and blue plastic 
respectively.
My thought is that you embed a matching Acme rod into the mold you melt the #2 
plastic in. Once cooled, you should be able to "unscrew" the rod from the 
plastic billet.  You then cut/machine the billet to the exterior measurements 
you need and then split it down the center line.  "Machining" can be done with 
your router, bandsaw, etc.

Does anyone have an idea of how well the #2 plastic (HDPE) will hold up?  Even 
if it wears down after 6 months of use - you will be able to reuse that worn 
out piece, with some added #2 plastic, and melt/mold a new piece.  If your mold 
& billet is long enough, you can produce a year's-worth in one mold.

If anyone tries this - or something similar, please share pictures and results.

Mac

  _____  

  _____  

-----Original Message----- 
From: 'joe biunno' via Legacy Ornamental Mills 
Sent: Aug 3, 2017 10:00 AM 
To: Legacy Ornamental Mills 
Subject: Re: Wood Chuck Tour by Mike Pung 

i'll offer an opinion here, as this could have been a problem for me on my 
recently acquired 1500...the problem is, due to the action/movement of the lead 
screw, the threads in the split nut wear sideways, especially when using a 
drive motor...think of each cross section of thread as a square(see photo)...I 
measured the cross section of the thread(in a new nut) to be .140" wide...in 
the photo of the worn nut, that same dimension is down to .065...so you could 
say the thread went from 1/8" full(new) to 1/16"...and sanding the nut down is 
not going to improve the function of the nut, in my opinion...maybe early on 
you can sand the nut to get a bit more life out of it, but that's it...the key 
to solving this problem is finding the 5/8-4 acme thread tap...once you have 
the tap, to make a new split nut is somewhat simple...and anyone who has that 
"hinged" split nut, I would swap that out and set up a sliding split nut...much 
more problematic to make that hinged split nut...so, if any member knows where 
to get that tap, here or overseas, please let the group know...I certainly 
would like to purchase one...barring that, I would also attempt to make a tap 
from some acme, threaded rod, if I had to...and the casting idea is also an 
excellent idea...joe b.

 


 
<http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient>
 

Virus-free.  
<http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient>
 www.avg.com 

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

Reply via email to