I copied this from the revo manual and I thought it was also on the legacy 
sight years ago when I bought my revo but I might be wrong but I did buy my 
first one from them through roger

 

Bill

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Tim Krause
Sent: Thursday, 10 August 2017 1:58 PM
To: Legacy Ornamental Mills
Cc: Richard Ellis; Legacy Ornamental Mills; Bawdsey 64
Subject: Re: Rotary Table Height

 

Legacy never sold a rotary table for Revo is BS unless the item shown in their 
instructions is non-produced.  It was smaller than the 900/1200/1800/1000 
machines.  Richard, can you photograph your rotary table?

Sent from BlueMail <http://www.bluemail.me/r?b=10256>  

On Aug 9, 2017, at 5:05 AM, Bawdsey64 <rhp...@gmail.com> wrote:

​Hi Richard

Don't blame Legacy, they never sold a rotary table for the REVO. That is fact 
confirmed by the Big Dog himself earlier today when I spoke to him. That Rotary 
Table was designed for 900, 1200 etc.

Regards
Roger


Sent from  <http://bit.ly/1PH8eIw> TouchMail for Windows 10

​

 

From: Richard Ellis

Received: 09/08/2017 12:08:48 +01:00

To: Legacy Ornamental Mills

Bill

When using the rotary table for the very first time, the handle came loose, it 
just did not rotate the table, it seemed as if it was only half on. so tried to 
move it nearer to the table---------it would not.

Tried to remove it to find out the problem, it was quite difficult to get off 
owing to the burs on the round shaft. Why no flat for the grub screw to clamp 
on.?????

Next---, went to fit the Universal joint to the spindle drive. did not go on 
far enough---------- the round part of the drive had score marks because of the 
fact that the recess in the Uni joint was not deep enough.I then checked the 
main rod of the Uni joint. Have Legacy never heard of a milling machine and the 
fact that one should not grub screw to round shafts.

As you say it is a great little machine but it seems I am spending far too much 
putting Legacy's shoddy workmanship to rights.

It seems to me over the years they are in too much of a hurry to bring out a 
new model, instead of making the first one properly.

Hence feeling a bit peed off at the moment.

Richard 

On Wednesday, August 9, 2017 at 11:45:10 AM UTC+1, aussiman wrote:

Sell the revo what on earth for a great little mill

 

Bill

 

From: legacy-orna...@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Richard Ellis
Sent: Wednesday, 9 August 2017 8:19 PM
To: Legacy Ornamental Mills
Cc: rchrd....@gmail.com; legacy-orna...@googlegroups.com
Subject: Re: Rotary Table Height

 

Roger

I did not want to alter the Revo, as Martin was promised it back if I decided 
to sell it.

Planing MDF is not a healthy thing to do unless well ventilated. I have been 
Routing a lot of Plywood and it upset me rather badly, a sore place on my face 
and a retching session, have just come back from the Doctor. Even though I was 
wearing a mask the air was polluted for a long long time

Am now thinking of selling the Revo and all the bits that came with it. as 
Martin does not now want it back..

Richard

On Sunday, August 6, 2017 at 5:24:57 PM UTC+1, ITwoodwork wrote:

​Hi  Richard

Why not plane the board that is on the rotary table down to your required 
thickness?

Just a suggestion.

Roger & Out!


Sent from  <http://bit.ly/1PH8eIw> TouchMail for Windows 10

​

 

From: Richard Ellis

Received: 06/08/2017 17:02:42 +01:00

To: Legacy Ornamental Mills

Today I fitted my Rotary Table to the Revo. It does not seem to have much 
height for hollowing out bowls  ----only 21/4 "--- The other thing I have found 
,the waste board, it's 3/4 " thick and appears to have been glued on. I can not 
see any woodscrews  holding it,,. Is that normal ?

If I put a thinner waste board I could gain another half inch.

Is there another way of lowering the table ?

Cheers 

Richard

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-orna...@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-orna...@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

 


 
<http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient>
 

Virus-free.  
<http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient>
 www.avg.com 

 

 


 
<http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient>
 

Virus-free.  
<http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient>
 www.avg.com 

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

Reply via email to