Great job, I like the relaxed twist. Also like the finger handle the
way you pinned it in place. Keep up the good work.
Mike OK
On 7/16/2023 5:53 PM, [email protected] wrote:
These were delivered this weekend. Old growth American black walnut.
Drilled 4" deep for stemmed flowers and tapered for standard candle.
Test tubes for water holding were late, so will be shipped later.
They look especially sharp with the classy glass bobeches in place
mimicking the saucer base. Can be seen in western Iowa.
ElizabethCandlesticks.JPG
DanK
On Friday, July 7, 2023 at 2:23:33 PM UTC-4 Tim Ziegler wrote:
Hey Dan,
Excited your working on a project again for sure.
Your Pic did not show up.
Are you using the single or double gear set between your drive
gear and duplex?
Kind Regards,
Timothy J. Ziegler
Ziegler WoodWork & Specialty
14171 160th Ave.
Foreston MN 56330
320-294-5798 <tel:(320)%20294-5798> shop
320-630-2243 <tel:(320)%20630-2243> cell
On Fri, Jul 7, 2023 at 10:34 AM [email protected]
<[email protected]> wrote:
Here is a prototype candlestick for a set of four matching for
my granddaughter. This is red oak, but the gift set will be
American black walnut. There will be a "saucer" with a carved
handle at the edge, you know, the old fashioned ring type.
That will give it "stability" both physically and visually. My
original intent was that in addition to the standard 7/8"
tapered socket, I would drill out for a test tube to allow a
couple of flower stems to be inserted instead of a candle. But
I'm having trouble finding a tube of 1/2" OD. It's a set of
four because she wanted two left twists and two right twists.
She has a rope candle mold that is right twist, and this would
allow her decorating options.
Is this a left hand twist?
DanK
--
You received this message because you are subscribed to the
Google Groups "Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from
it, send an email to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/legacy-ornamental-mills/585cda5c-93f0-4328-b2d5-5f9696b4e901n%40googlegroups.com
<https://groups.google.com/d/msgid/legacy-ornamental-mills/585cda5c-93f0-4328-b2d5-5f9696b4e901n%40googlegroups.com?utm_medium=email&utm_source=footer>.
--
You received this message because you are subscribed to the Google
Groups "Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send
an email to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/legacy-ornamental-mills/92b1afa9-a5bf-403a-8157-01467e18228an%40googlegroups.com
<https://groups.google.com/d/msgid/legacy-ornamental-mills/92b1afa9-a5bf-403a-8157-01467e18228an%40googlegroups.com?utm_medium=email&utm_source=footer>.
--
You received this message because you are subscribed to the Google Groups "Legacy
Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/legacy-ornamental-mills/3fe7750e-ed44-9191-3955-16d3cfa33dfc%40iglide.net.
