Thanks Curt good stuff. Kind Regards,
Timothy J. Ziegler Ziegler WoodWork & Specialty Ziegler Laser Worx LLC 14171 160th Ave. Foreston MN 56330 320-294-5798 shop 320-630-2243 cell On Sun, Apr 7, 2024 at 9:56 PM 'Curt George' via Legacy Ornamental Mills < legacy-ornamental-mills@googlegroups.com> wrote: > We did have a gentleman in our group, who made his own gear linkage a few > years back. > his gear reduction set looks more like Legacy's 2000 & 2200 gear linkage. > but his was appx. 4yrs before Legacy. > My set up is much simpler, It may have some draw backs? but With Simple, > Others can pick up from where I left off. (modifying and or making there > own parts.) If its to complex no one will ever try to understand and make > it. The main focus point is the learn and grow. > Here are some of his old photo's and a link to this topic. > Joe Gassen made a X8 gear set. > > > <https://groups.google.com/forum/#!searchin/legacy-ornamental-mills/$20gear$20set$2F$20joe$20gassen/legacy-ornamental-mills/NRI4-q17xz8/RIIWbhMU078J> > https://groups.google.com/forum/#!searchin/legacy-ornamental-mills/$20gear$20set$2F$20joe$20gassen/legacy-ornamental-mills/NRI4-q17xz8/RIIWbhMU078J > > C.A.G. > On Sunday, April 7, 2024 at 10:18:36 PM EDT, Tim Ziegler < > timjzieg...@gmail.com> wrote: > > > good stuff, Curt. Look forward to you testing it and seeing some results > too. > Very innovative. You just need to figure out how to add another small gear > to make it directional. > Kind Regards, > > Timothy J. Ziegler > Ziegler WoodWork & Specialty > Ziegler Laser Worx LLC > 14171 160th Ave. > Foreston MN 56330 > > 320-294-5798 shop > 320-630-2243 cell > > > On Sun, Apr 7, 2024 at 9:12 PM 'Curt George' via Legacy Ornamental Mills < > legacy-ornamental-mills@googlegroups.com> wrote: > > Hello everyone. > > Just finished off the New X-4 gear set. (to be fully honest with you all, > Its just a re-make of my old X,2,3,4, gear set.) > The idea was to use the Legacy gears that I own to reduce the gears > movement/ speeding the pitch up. > This gear set, goes in the placement of the directional gears. This gear > set can be added to any of the other Legacy gear sets. > > And example if I use the standard gear set, so it was to make a 3" pitch, > If I add this X-4 to the linkage, I would then make a 12" pitch. > > The key is making a gear linkage with a 5/16" square and a set of ball- > bearings to hold the shaft. then I used my 96 tooth gear ("A" gear) > and a 24 tooth gear. ("F" gear ???)(I think? I have 2 but they may be a > custom made gear? I did have a number odd sized gears made some yrs. back.) > I have not yet fully tested this gear set, Yet. (but hope to do my testing > tomorrow.) > The photo's show the gear set piece by piece. First the frame with shaft > and ball bearing sets. second the gears stacked on the shaft. > and third the full assembly. and lastly the gear chart. > > I hope this helps everyone understand the process, and how it was made. > > Have a good night. > > C.A.G. > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/633183009.3906894.1712542320744%40mail.yahoo.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/633183009.3906894.1712542320744%40mail.yahoo.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLEPNfHL-hfcY5tavuKdNaGfhW4yGZoyp_ec43y5K7aTnA%40mail.gmail.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLEPNfHL-hfcY5tavuKdNaGfhW4yGZoyp_ec43y5K7aTnA%40mail.gmail.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to legacy-ornamental-mills+unsubscr...@googlegroups.com. > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/1176985588.3907830.1712545012547%40mail.yahoo.com > <https://groups.google.com/d/msgid/legacy-ornamental-mills/1176985588.3907830.1712545012547%40mail.yahoo.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLEQZMXMM2uQPTfDqcB8XfGMghu9AXu29F9%2BuURMDNx%2BwQ%40mail.gmail.com.
