Hello Mr Ziegler, I just joined this group and was wondering if you might give me some direction of how to go about posting/selling my LOM. Any guidance is appreciated. I am assuming this would be a good place to advertise it for sale.
Ken Fisher > > On Aug 13, 2024 at 1:46 PM, <Tim Ziegler (mailto:[email protected])> > wrote: > > > > Hey Tim M, > > > > > I think about the only router that a lot of LOM's were drilled for was the > Porter Cable. > > Though I could be wrong on the REVO. I have a plunge Makita on mine. > > I have several Makita Routers on my LOM's but one has a craftsman commercial > and > > I also have the Big Porter Cables on a couple. > > My suggestion is line it up to how you want the handles so they are out of > the way and > > orientate the switch to a convenient spot and drill away. Make sure you > have a good way > > get as centered as possible. > > My two cents worth of advice. > > > > > > Kind Regards, > > > Timothy J. Ziegler > > Ziegler WoodWork & Specialty > > Ziegler Laser Worx LLC > > 14171 160th Ave. > > Foreston MN 56330 > > > > 320-294-5798 shop > > 320-630-2243 cell > > > > > > > > On Tue, Aug 13, 2024 at 3:33 PM Tim Maxwell <[email protected] > (mailto:[email protected])> wrote: > > > > > Before I start drilling new holes or enlarging existing holes, is the > > carrier plate on the Revo supposed to be predrilled for Bosch routers? > > > > > > The Revo training videos show what I think is a Bosch 1617 EVS mounted, > > but I can not even get two of the dozen holes in my plate to line up at the > > same time. The holes all appear to have power coat so I think they are > > factory instead of previous owner. > > > > > > Tim M > > > > > > > > > > > > > > -- > > You received this message because you are subscribed to the Google Groups > > "Legacy Ornamental Mills" group. > > To unsubscribe from this group and stop receiving emails from it, send an > > email to [email protected] > > (mailto:[email protected]). > > To view this discussion on the web visit > > https://groups.google.com/d/msgid/legacy-ornamental-mills/2e7b1342-1251-45fe-8f7a-7ac651f140b2n%40googlegroups.com > > > > (https://groups.google.com/d/msgid/legacy-ornamental-mills/2e7b1342-1251-45fe-8f7a-7ac651f140b2n%40googlegroups.com?utm_medium=email&utm_source=footer). > > > > > > -- > You received this message because you are subscribed to the Google Groups > "Legacy Ornamental Mills" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected] > (mailto:[email protected]). > To view this discussion on the web visit > https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFDM393593YD6YEZStaVbXHuu2SrtKJQq3EYXVtZi7KOQ%40mail.gmail.com > > (https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFDM393593YD6YEZStaVbXHuu2SrtKJQq3EYXVtZi7KOQ%40mail.gmail.com?utm_medium=email&utm_source=footer). > -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/BY5PR10MB4001EE8BC6B6E3CFEA3CFA37B3862%40BY5PR10MB4001.namprd10.prod.outlook.com.
