> Something doesn't look right here, and I don't have time > to fully investigate right now. Any hint is always precious: > > Basically, it should not be sending a report ID if there > are no report IDs defined in the HID report descriptor > (note that it says "length: 6" but you passed in an > array of 5 bytes). What do you mean for report ID? The message to be sent to device? But before sending report, I can't find the item-address to send to:
WARNING: hid_find_object(): can't find requested item 0xff000001.0x00010046.0x000a0001 of USB device 002/002-1b67-000a-00-00[0]. I tryed almost every combination of what test_libhid tells about the device: path: 0xff000001.0xff000002; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00000000; type: 0xb0 path: 0xff000001.0x00010046.0x000a0001; type: 0x80 path: 0xff000001.0x00010046.0x00000000.0x000a0040; type: 0x80 path: 0xff000001.0x00010046.0x00000000.0x000a0041; type: 0x80 path: 0xff000001.0x00010046.0x00000000.0x000a0042; type: 0x80 > For the hid_interrupt_read error, you may need to set the > USB_DEBUG environment variable to something non-zero. I will add this and retry, but I'm working abroad and I can access my mail only at the office, so I can tell tomorrow about this... thanks a lot! domenico > -- > Charles Lepple > > _______________________________________________ libhid-discuss mailing list [email protected] http://lists.alioth.debian.org/mailman/listinfo/libhid-discuss
