>>>>> "Mats" == Mats Bengtsson <[EMAIL PROTECTED]> writes:
Mats> Did you compile it yourself or install from an RPM? Are the Mats> symbols missing both in DVI, PS, PDF and printed output? Mats> Do the PDF files from the on-line examples at the documentation Mats> page for your LilyPond version work on your computer? Mats> If it's only a problem in the PS and PDF files, but the DVI Mats> files look OK, take a look at the output of (use Mats> piano-dynamics.ly from the Templates section of the Mats> Documentation): lilypond -V piano-dynamics.ly Mats> At the end of the output, you should see something like Mats> Invoking `dvips -ta4 -Ppdf -G0 -u +lilypond.map Mats> -opiano-dynamics.ps piano-dynamics.dvi'This is dvips(k) 5.92b Mats> Copyright 2002 Radical Eye Software (www.radicaleye.com) ' TeX Mats> output 2004.11.03:1102' -> piano-dynamics.ps Mats> <tex.pro><alt-rule.pro><texc.pro><f7b6d320.enc><music-drawing-routines.ps> Mats> <texps.pro><special.pro>. <cmr10.pfb><feta-braces50.pfa><feta-din14.pfa> Mats> <feta20.pfa><cmbx10.pfb>[1] Mats> Look especially for the feta-braces* and feta-din*. Mats> /Mats Mats> Victor S. Miller wrote: >> I've installed LP 2.2.6 on RH 9. Things work fairly well, except >> for the following which I would guess is some sort of font problem: >> No brace is printed to the left of a piano staff (even from some of >> the precanned examples). No dynamic markings, like p, pp, etc. are >> printed. Any suggestions about tracking down the cause? No error >> messages are given. I do get lots of warnings from xpdf when >> viewing the pdfs, about bad bounding boxes. Mats> -- ============================================= Mats Bengtsson Mats> Signal Processing Signals, Sensors and Systems Royal Institute Mats> of Technology SE-100 44 STOCKHOLM Sweden Phone: (+46) 8 790 8463 Mats> Fax: (+46) 8 790 7260 Email: [EMAIL PROTECTED] WWW: Mats> http://www.s3.kth.se/~mabe Mats> ============================================= Mats> mktexpk: Mismatched mode ljfour and resolution 8000; ignoring Mats> mode. Well, the dvi files look ok. When I try lilypond -V piano-dyanamics.ly I get the following (relevant excerpt only): mktexpk: Can't guess mode for 8000 dpi devices. mktexpk: Use a config file, or update me. kpathsea: Appending font creation commands to missfont.log. dvips: Font feta20 at 8000 not found; scaling 600 instead. dvips: Such scaling will generate extremely poor output. kpathsea: Running mktexpk --mfmode ljfour --bdpi 8000 --mag 1+0/8000 --dpi 8000 feta-din14 mktexpk: Mismatched mode ljfour and resolution 8000; ignoring mode. mktexpk: Can't guess mode for 8000 dpi devices. mktexpk: Use a config file, or update me. dvips: Font feta-din14 not found, using cmr10 instead. dvips: Design size mismatch in font feta-din14 dvips: Checksum mismatch in font feta-din14 kpathsea: Running mktexpk --mfmode ljfour --bdpi 8000 --mag 1+0/8000 --dpi 8000 feta-braces50 mktexpk: Mismatched mode ljfour and resolution 8000; ignoring mode. mktexpk: Can't guess mode for 8000 dpi devices. mktexpk: Use a config file, or update me. dvips: Font feta-braces50 not found, using cmr10 instead. dvips: Design size mismatch in font feta-braces50 dvips: Checksum mismatch in font feta-braces50 What do you suggest I do now? Victor _______________________________________________ lilypond-user mailing list [EMAIL PROTECTED] http://lists.gnu.org/mailman/listinfo/lilypond-user
