On 11 Oct 2010, at 23:08, Matt Waddel <matt.wad...@canonical.com> wrote:
> Hi Jamie, > > On 10/11/2010 03:03 PM, Jamie Bennett wrote: >> On Mon, Oct 11, 2010 at 01:13:40PM +0100, Harry Liebel wrote: >>> I've had mixed results. When the box completes the boot the basic systems >>> seem to work ok (I can get an IP and poke the filesystem). It still takes >>> several minutes to get to a prompt as mentioned on the wiki page. >>> >>> It happens quite often that the box does not get to a prompt at all. It >>> fails to read the MMC properly. Below is two separate cases where reading >>> the partition table fails. In the first case it finds one partition and in >>> the second case it fails to find any partitions. The boot monitor has no >>> problem reading uboot, kernel or initrd from the MMC when writing to >>> internal FLASH. >>> >>> I've also tried a different SD card with similar results. Sometimes it >>> works fine and other times it reports I/O errors. I've tried the daily >>> builds for 6, 8 and 10 October. Is this a known issue? >> >> I can't fix your problem but for extra brownie points you could >> register this in launchpad as a bug and we can push for the right >> people to investigate. >> >> Please file a bug at: >> >> http://bugs.launchpad.net/linux-linaro >> >> (sounds like a kernel related issue) and we will take it from there :) > > We've already opened a bug on this issue: > > https://bugs.launchpad.net/ubuntu/+source/linux-linaro/+bug/632798 Great, thanks. > --Matt Regards, Jamie. >> >>> ----- >>> >>> mmc0: host does not support reading read-only switch. assuming write-enable. >>> mmc0: new SD card at address 8fe4 >>> mmcblk0: mmc0:8fe4 SD02G 1.84 GiB >>> mmcblk0: >>> Freeing init memory: 160K >>> p1ding, please wait... >>> p2 >>> udev[497]: starting version 163 >>> port 1 high speed >>> Begin: Loading essential drivers ... done. >>> Begin: Running /scripts/init-premount ... done. >>> Begin: Mounting root file system ... Begin: Running /scripts/local-top ... >>> done. >>> usb 1-1: new high speed USB device using isp1760 and address 2 >>> port 1 high speed >>> usb 1-1: New USB device found, idVendor=0471, idProduct=3526 >>> usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 >>> usb 1-1: Product: ISP1520 >>> usb 1-1: Manufacturer: Philips Semiconductors >>> mmcblk0: retrying using single block read >>> mmcblk0: error -5 transferring data, sector 0, nr 8, card status 0xb00 >>> hub 1-1:1.0: USB hub found >>> hub 1-1:1.0: 3 ports detected >>> end_request: I/O error, dev mmcblk0, sector 0 >>> Buffer I/O error on device mmcblk0, logical block 0 >>> >>> ----- >>> >>> mmc0: host does not support reading read-only switch. assuming write-enable. >>> mmc0: new SD card at address 8fe4 >>> mmcblk0: mmc0:8fe4 SD02G 1.84 GiB >>> mmcblk0: >>> TCP cubic registered >>> NET: Registered protocol family 10 >>> lo: Disabled Privacy Extensions >>> NET: Registered protocol family 17 >>> port 1 high speed >>> VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 0 >>> Registering SWP/SWPB emulation handler >>> rtc-pl031 mb:rtc: setting system clock to 2010-10-11 10:49:28 UTC >>> (1286794168) >>> usb 1-1: new high speed USB device using isp1760 and address 2 >>> Freeing init memory: 160K >>> port 1 high speed >>> mmcblk0: retrying using single block read >>> Loading, please wait... >>> usb 1-1: New USB device found, idVendor=0471, idProduct=3526 >>> usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 >>> udev[493]: starting version 163 >>> Begin: Loading eusb 1-1: Product: ISP1520 >>> mmcblk0: error -5 transferring data, sector 2, nr 6, card status 0x900 >>> end_request: I/O error, dev mmcblk0, sector 2 >>> ssential driversusb 1-1: Manufacturer: Philips Semiconductors >>> ... done. >>> Begin: Runnimmcblk0: error -5 transferring data, sector 3, nr 5, card >>> status 0x900 >>> ng /scripts/initend_request: I/O error, dev mmcblk0, sector 3 >>> -premount ... done. >>> Begin: Mounting root file system ... hub 1-1:1.0: USB hub found >>> hub 1-1:1.0: 3 ports detected >>> Begin: Running /scripts/local-tommcblk0: error -5 transferring data, sector >>> 5, nr 3, card status 0xb00 >>> p ... done. >>> end_request: I/O error, dev mmcblk0, sector 5 >>> unable to read partition table >>> >>> ----- >>> >>> Thanks, >>> Harry >>> >>> >>> >>> -- IMPORTANT NOTICE: The contents of this email and any attachments are >>> confidential and may also be privileged. If you are not the intended >>> recipient, please notify the sender immediately and do not disclose the >>> contents to any other person, use it for any purpose, or store or copy the >>> information in any medium. Thank you. >>> >>> _______________________________________________ >>> linaro-dev mailing list >>> linaro-dev@lists.linaro.org >>> http://lists.linaro.org/mailman/listinfo/linaro-dev >> >> _______________________________________________ >> linaro-dev mailing list >> linaro-dev@lists.linaro.org >> http://lists.linaro.org/mailman/listinfo/linaro-dev > > > _______________________________________________ > linaro-dev mailing list > linaro-dev@lists.linaro.org > http://lists.linaro.org/mailman/listinfo/linaro-dev _______________________________________________ linaro-dev mailing list linaro-dev@lists.linaro.org http://lists.linaro.org/mailman/listinfo/linaro-dev
