Hello Leif, I use VESA 1280x1024 @ 60Hz / 24bit with X11.
The values I sent before are with a signal selected. Percentages change a little with the selected filter bandwidths (+-3%). Without selecting a signal the figures are: 02.27: no FFT2: 12% with FFT2: 28% 02.19: no FFT2: 9% with FFT2: 26% Hope it helps. Daniel, DL3IAE -------- Original-Nachricht -------- Datum: Fri, 6 Apr 2007 23:26:16 +0200 Von: Leif Asbrink <[EMAIL PROTECTED]> An: "Linrad mailinglist" <linrad@antennspecialisten.se> Betreff: [linrad] Re: Increased CPU usage > Hello Daniel, > > I tried the parameters that you sent. (without fft2) > These are the results: > > Pentium IV at 2.66 GHz, Debian Etch, Linrad-02-28: 4% > Pentium IV at 2.66 GHz, Debian Etch, Linrad-02.21: 5% > Pentium III at 800 MHz, Suse 9.1, Linrad-02.28: 7% > Pentium III at 800 MHz, Suse 9.1, Linrad-02.21: 18% > > This is in terminal mode with svgalib. > > Under X11 the load is similar on the Pentium IV > but it is about 16% on the Pentium III for both > Linrad-02.21 and 02-28. > > Linrad-02-28 should be identical to 02-27 when it comes to > timings. The differences are in the calibration routines only. > > The differences I see between the latest and earlier versions > go in the opposite direction to what you observe. The difference > (by a factor of about 2.5) is very large and shows that I > corrected some error. Presumably I did not do it right since > you observe a change in the opposite direction. > > Are you running with svgalib or under X11? If X11, what is the > screen size and colour depth that you use? > > 73 > > Leif > > > > > > Hello Leif, > > > > there seems to be significant increase from 02.23 to 02.27 regarding the > CPU usage. > > > > On my system (AMD Duron 1,3 GHz, 512Mb RAM) I see the following figures: > > > > Linux (Suse 9.1): > > > > 02.19 (02.23 is the same) > > FFT2 off: 19% > > FFT2 on: 37% > > > > > > 02.27 > > FFT2 off: 36% > > FFT2 on: 53% > > [EMAIL PROTECTED] > > ---------------- > > > > Win2K: > > wlr 02.27 > > > > FFT2 off: 22% > > FFT2 on: 37% > > > > > > This is with the same parameter files for all versions. It doesn't > bother me much, just curious to know why. > > > > On ON5GN's system there is not much of an increase but Pierre is using > modern hardware. > > > > > > 73 > > > > Daniel, DL3IAE > > > > -- > > http://dl0ger-eme.dd8il.de/ > > > > "Feel free" - 10 GB Mailbox, 100 FreeSMS/Monat ... > > Jetzt GMX TopMail testen: http://www.gmx.net/de/go/topmail > > > > ############################################################# > > This message is sent to you because you are subscribed to > > the mailing list <linrad@antennspecialisten.se>. > > To unsubscribe, E-mail to: <[EMAIL PROTECTED]> > > To switch to the DIGEST mode, E-mail to > <[EMAIL PROTECTED]> > > To switch to the INDEX mode, E-mail to > <[EMAIL PROTECTED]> > > Send administrative queries to <[EMAIL PROTECTED]> > > > > ############################################################# > This message is sent to you because you are subscribed to > the mailing list <linrad@antennspecialisten.se>. > To unsubscribe, E-mail to: <[EMAIL PROTECTED]> > To switch to the DIGEST mode, E-mail to > <[EMAIL PROTECTED]> > To switch to the INDEX mode, E-mail to > <[EMAIL PROTECTED]> > Send administrative queries to <[EMAIL PROTECTED]> -- http://dl0ger-eme.dd8il.de/ "Feel free" - 10 GB Mailbox, 100 FreeSMS/Monat ... Jetzt GMX TopMail testen: http://www.gmx.net/de/go/topmail ############################################################# This message is sent to you because you are subscribed to the mailing list <linrad@antennspecialisten.se>. To unsubscribe, E-mail to: <[EMAIL PROTECTED]> To switch to the DIGEST mode, E-mail to <[EMAIL PROTECTED]> To switch to the INDEX mode, E-mail to <[EMAIL PROTECTED]> Send administrative queries to <[EMAIL PROTECTED]>