Thanks a lot for all the help, the problem was that i never told to x3270
the luname (i know, im very stupid, but after 20 hours of switching from a
multiprise to our new z800 i was really tired), but now we have another
problem:
I call x3270 with: x3270 prod@ipaddress:3270
then i get:
** 2074 Index 02 connected to ESCON via IP Address ipaddress:3270
** CA=0 Index=02 LPAR=1 Port=01 CU=0 UA=01 LUName=prod
** Type=002066-0A1 Mfg=IBM SN=00000001900A Tag=000C Link=0C Status=Active
then, with a tso session (we use os/390 2.6) i do:
V 301,CONSOLE,ROUT=ALL
IEE687I CONSOLE CONSALTR ATTRIBUTES REMOVED FROM CONSOLE CONSMSTR
D C,U=(0301),L=IBMUSER-Z
IEE889I 13.19.41 CONSOLE DISPLAY 063
MSG: CURR=1 LIM=5000 RPLY:CURR=0 LIM=20 SYS=SFPROD PFK=26
CONSOLE/ALT ID --------------- SPECIFICATIONS ---------------
CONSALTR/CONSMSTR 02 COND=A AUTH=ALL NBUF=0 UD=N
0301 AREA=Z MFORM=T,J
SFPROD DEL=RD RTME=1 RNUM=20 SEG=20 CON=N
USE=FC LEVEL=ALL PFKTAB=PFKTAB1
ROUTCDE=ALL
MONITOR=JOBNAMES
and then i get the error:
IEE870I CONSOLE SWITCH, OLD=0301(CONSALTR,SFPROD ) NEW=0300(CONSMSTR,
SFPROD ) REASON=IOER
reading "OS/390 MVS System Messages, Volume 4 (IEC-IFD)" i found that the
message is because a console switch occur (really obviusly) and that an io
error ocurred (again, really obiusly), but why and io error ocurred and
what error?, the device number is correct and everything else, so im
really confused :(
thanks.
On Thu, 23 Jan 2003, Paul Winder wrote:
> When you connect you need to specify the LUNAME configured in the 2074,
> then it goes something like:
> x3270 LUNAME@ipaddress:3270
>
> In our installation the LUNAME corresponds to the LPAR name, so it might be:
> x3270 LINUX1@ipaddress:3270
>
> Paul Winder
>
> Davis, Lawrence wrote:
>
> > I believe the port on the 2074 is configurable, but the default is 3270
> >
> > Larry Davis
> >
> >
> > -----Original Message-----
> > From: Vic Cross [mailto:[EMAIL PROTECTED]]
> > Sent: Thursday, January 23, 2003 00:21
> > To: [EMAIL PROTECTED]
> > Subject: Re: tn3270e
> >
> >
> > On Wed, 22 Jan 2003, Alex Leyva wrote:
> >
> >
> >>Hi, we have just installed our new z800, we are using one 2074 to get the
> >>consoles, but we have one problem, we want to use linux but we cant find a
> >>tn3270e emulator
> >>
> >
> > As Paul posted, x3270 should work ok (I use x3270 to connect to MP3000 and
> > P/390 machines, and the 2074 uses the same code...).
> >
> >
> >>we try to use x3270 but obviusly it get an "unknown
> >>error" when we try to connect to the 2074
> >>
> >
> > More information required. Is the error on the Linux box, or on the 2074?
> > Is it in the 3270 window on x3270?
> >
> > I think it's a configuration problem. I'm pretty sure the 2074 uses a
> > non-standard tn3270 port (not the usual telnet port 23 but something like
> > 7490, just like the MP3000 and P/390 do). You will need to configure this
> > in x3270, but doing this is tricky and version dependent (from my
> > experience). You can try either of the following:
> >
> > # x3270 ipaddress:7490
> > # x3270 ipaddress 7490
> >
> > but the one that should work, regardless of version, is
> >
> > # x3270 --port 7490 ipaddress
> >
> > Of course, confirm that 7490 is the correct port number on your 2074;
> > substitute the right value if it's not 7490.
> >
> > Hope this helps,
> > Vic Cross
> >
> >
> >
>
--
Alejandro Leyva Rabinovich.
Jefe de la Unidad Departamental de Soporte Ticnico
(Administracisn de Mainframe).
Direccisn General de Informatica.
Secretarma de Finanzas.
Gobierno del Distrito Federal.
