Yes Mark, it does. Please see below.
Do I have to set up the z/VM TCP/IP stack with Hipersocket definitions in order
to get Linux (z/VM guest) server connected to
z/OS LPAR?.
Thank you.
linuxtst:~ # ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:02:55:89:5C:13
inet addr:10.10.10.55 Mask:255.255.255.0
inet6 addr: fe80::2:5500:1589:5c13/10 Scope:Link
UP RUNNING MULTICAST MTU:1500 Metric:1
RX packets:146 errors:0 dropped:0 overruns:0 frame:0
TX packets:129 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:7877 (7.6 Kb) TX bytes:26279 (25.6 Kb)
hsi1 Link encap:Ethernet HWaddr 00:00:00:00:00:00
inet addr:10.10.9.72 Mask:255.255.255.0
inet6 addr: fe80::200:ff:fe00:0/10 Scope:Link
UP RUNNING NOARP MULTICAST MTU:16384 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:20 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:2236 (2.1 Kb)
Interrupt:3
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
sit0 Link encap:IPv6-in-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Hugo Rivera
SSA II
County of Contra Costa
Department of Information Technology
30 Douglas Drive,
Martinez, CA 94553-4068
Tel: (925) 313-1309
Nextel: (925) 383-5781
Fax: (925) 313-1459
Pager: (925) 975-7479
email: [EMAIL PROTECTED]
"Post, Mark K"
<[EMAIL PROTECTED] To:
[email protected]
M> cc:
Sent by: Linux on Subject: Re: Hipersocket - qdio
error messages
390 Port
<[EMAIL PROTECTED]
IST.EDU>
01/05/2005 01:36
PM
Please respond to
Linux on 390 Port
Those don't look like errors to me, just informational messages. Looks like
everything is up and running. Does an "ifconfig -a" command show both eth0
and hsi1?
Mark Post
-----Original Message-----
From: Linux on 390 Port [mailto:[EMAIL PROTECTED] On Behalf Of Hugo
Rivera
Sent: Wednesday, January 05, 2005 3:29 PM
To: [email protected]
Subject: Hipersocket - qdio error messages
Hello list -
I'm trying to connect a Linux (z/VM guest) server with a z/OS LPAR via
HiprSockets and I'm getting the following error messages when I reboot
the Linux server. I can't ping from Linux to z/OS or viceversa.
qeth: Trying to use card with devnos 0x7100/0x7101/0x7102
qdio : Adapter interruption facility not installed.
qdio : Not all CHSCs supported. Continuing.
qeth: Device 0x7100/0x7101/0x7102 is a HiperSockets card (level: D3GF)
with link type magic (portname: )
qeth: VLAN not supported on hsi1
qeth: IPv6 not supported on hsi1
qeth: Broadcasting not supported on hsi1
qeth: Trying to use card with devnos 0x1004/0x1005/0x1006
qeth: Device 0x1004/0x1005/0x1006 is an OSD Express card (level: 0358)
with link type Fast Eth (portname: ETHPORT1)
eth0: no IPv6 routers present
hsi1: no IPv6 routers present
I would appreciate any help.
Thank you.
Hugo Rivera
SSA II
County of Contra Costa
Department of Information Technology
----------------------------------------------------------------------
For LINUX-390 subscribe / signoff / archive access instructions,
send email to [EMAIL PROTECTED] with the message: INFO LINUX-390 or
visit
http://www.marist.edu/htbin/wlvindex?LINUX-390
----------------------------------------------------------------------
For LINUX-390 subscribe / signoff / archive access instructions,
send email to [EMAIL PROTECTED] with the message: INFO LINUX-390 or visit
http://www.marist.edu/htbin/wlvindex?LINUX-390
----------------------------------------------------------------------
For LINUX-390 subscribe / signoff / archive access instructions,
send email to [EMAIL PROTECTED] with the message: INFO LINUX-390 or visit
http://www.marist.edu/htbin/wlvindex?LINUX-390
