Thanks, Jan. You identified the problem. I failed to put the disk in /etc/zipl.conf before doing zipl. A colleague and I managed to stumble onto that after some struggle last night. I didn't see your email until this morning, but the link is just what I needed. It looks familiar, I bet I have read it before, but had just forgotten about it. I don't work with RHEL that often. You can bet it is bookmarked now.
Martha Martha McConaghy Marist: System Architect/Technical Lead SHARE Association: Vice President Marist College IT Poughkeepsie, NY 12601 ________________________________ From: Linux on 390 Port <LINUX-390@VM.MARIST.EDU> on behalf of Jan Stodola <jstod...@redhat.com> Sent: Thursday, April 16, 2020 3:36 AM To: LINUX-390@VM.MARIST.EDU <LINUX-390@VM.MARIST.EDU> Subject: Re: Adding disk to root LVM with RHEL 7 On Wed, Apr 15, 2020 at 10:29 PM Martha McConaghy < martha.mccona...@marist.edu> wrote: > I feel like Alice through the looking glass at this point. I was hopeful > that mkinitrd would do the trick, but now I have a whole new problem. > After bringing the disk online, adding it to /etc/dasd.conf, I ran mkinitrd > and zipl. Then, I rebooted. I did NOT touch the LVM, or anything, at that > point. This resulted in a bunch of dracut timeout errors and am now in > dracut emergency mode. I'm about to give up and just give this darned > thing a TB LUN and be done with it. But, this shouldn't be so hard for > crying out loud. Its bugging me that I don't know what I'm doing wrong. > The RedHat web site lets me log in, but won't show me their solution > pages....arggg..... > Hi Martha, check the steps in the RHEL-7 documentation, there is no need to log in: https://access.redhat.com/documentation/en-us/red_hat_enterprise_linux/7/html/installation_guide/chap-post-installation-configuration-s390#sect-post-installation-adding-dasds-s390 You should not need to re-create initrd if you specify the new DASD device ID on the kernel command line. > > So, any thoughts? > > Martha > > Pre-reboot: > > [root@opncl42 ~]# cio_ignore -l > Ignored devices: > ================= > [root@opncl42 ~]# chccwdev --online 0.0.0200 > Setting device 0.0.0200 online > Done > [root@opncl42 ~]# lsdasd > Bus-ID Status Name Device Type BlkSz Size Blocks > > ============================================================================== > 0.0.0150 active dasda 94:0 ECKD 4096 46068MB 11793420 > 0.0.0200 active dasdb 94:4 ECKD 4096 23033MB 5896620 > [root@opncl42 ~]# vi /etc/dasd.conf > [root@opncl42 ~]# mkinitrd -f /boot/initramfs-3.10.0-1127.el7.s390x.img > 3.10.0-1127.el7.s390x > [root@opncl42 ~]# zipl > Using config file '/etc/zipl.conf' > Building bootmap in '/boot' > Building menu 'zipl-automatic-menu' > Adding #1: IPL section '3.10.0-1127.el7.s390x' (default) > Adding #2: IPL section '3.10.0-1127.el7.s390x_with_debugging' > Adding #3: IPL section 'linux' > Preparing boot device: dasda (0150). > Done. > [root@opncl42 ~]# reboot > > Post-reboot: > > Ý"Ý32m OK "Ý0m+ Reached target System Initialization. > Ý 1.149462+ dasd-eckd 0.0.0150: A channel path to the device has become > opera > tional > Ý 1.151741+ dasd-eckd 0.0.0150: New DASD 3390/0C (CU 3990/01) with > 65519 cyli > nders, 15 heads, 224 sectors > Ý 1.153040+ dasd-eckd 0.0.0150: DASD with 4 KB/block, 47173680 KB total > size, > 48 KB/track, linux disk layout > Ý 1.153145+ qeth: register layer 2 discipline > > Ý 1.154257+ qdio: 0.0.0702 OSA on SC 5 using AI:1 QEBSM:0 PRI:1 TDD:1 > SIGA:RW > A > Ý 1.155122+ dasda:VOL1/ 0X0150: dasda1 dasda2 > Ý 1.156584+ dasd-eckd 0.0.0200: A channel path to the device has become > opera > tional > Ý 1.159045+ dasd-eckd 0.0.0200: New DASD 3390/0C (CU 3990/01) with > 32759 cyli > nders, 15 heads, 224 sectors > Ý 1.159581+ dasd-eckd 0.0.0200: DASD with 4 KB/block, 23586480 KB total > size, > 48 KB/track, compatible disk layout > Ý 1.160634+ dasdb:VOL1/ 0X0200: dasdb1 > Ý"Ý32m OK "Ý0m+ Started Show Plymouth Boot Screen."" > Ý"Ý32m OK "Ý0m+ Reached target Paths."" > Ý"Ý32m OK "Ý0m+ Started Forward Password Requests to Plymouth Directory > Watch. > "" > Ý"Ý32m OK "Ý0m+ Reached target Basic System."" > Ý 1.169428+ netif_napi_add() called with weight 128 on device eth%d > Ý 1.169600+ qeth 0.0.0700: MAC address 02:01:42:00:00:08 successfully > registered on device eth0 > Ý 1.169613+ qeth 0.0.0700: Device is a Virtual NIC QDIO card (level: > V712) > Ý 1.169613+ with link type Virt.NIC QDIO (portname: ) > Ý 124.355856+ dracut-initqueueÝ363+: Warning: dracut-initqueue timeout - > starting timeout scripts"" > Ý 124.862823+ dracut-initqueueÝ363+: Warning: dracut-initqueue timeout - > starting timeout scripts"" > Ý 125.366826+ dracut-initqueueÝ363+: Warning: dracut-initqueue timeout - > starting timeout scripts"" > ...lots of timeout script errors....... > Ý 184.424496+ dracut-initqueueÝ363+: Warning: dracut-initqueue timeout - > starting timeout scripts"" > Ý 184.424755+ dracut-initqueueÝ363+: Warning: Could not boot."" > Ý 184.425825+ dracut-initqueueÝ363+: Warning: > /dev/mapper/rhel_opncl41-root does not exist" > Starting Dracut Emergency Shell..." > Warning: /dev/mapper/rhel_opncl41-root does not exist > > Generating "/run/initramfs/rdsosreport.txt" > > > Entering emergency mode. Exit the shell to continue. > Type "journalctl" to view system logs. > You might want to save "/run/initramfs/rdsosreport.txt" to a USB stick or > /boot > after mounting them and attach it to a bug report. > > > > > > > Martha McConaghy > > Marist: System Architect/Technical Lead > > SHARE Association: Vice President > > Marist College IT > > Poughkeepsie, NY 12601 > > ________________________________ > From: Linux on 390 Port <LINUX-390@VM.MARIST.EDU> on behalf of Marcy > Cortes <marcy.d.cor...@wellsfargo.com> > Sent: Wednesday, April 15, 2020 11:42 AM > To: LINUX-390@VM.MARIST.EDU <LINUX-390@VM.MARIST.EDU> > Subject: Re: Adding disk to root LVM with RHEL 7 > > I'm kind of assuming RH7 works like sles11 and doesn't use grub2, but did > you "mkinird; zipl" after getting that disk online? > > You can also "cat / run/initramfs/rdsosreport.txt" in that emergency mode > to get more details. > > > > > -----Original Message----- > From: Linux on 390 Port <LINUX-390@VM.MARIST.EDU> On Behalf Of Rick Troth > Sent: Wednesday, April 15, 2020 8:26 AM > To: LINUX-390@VM.MARIST.EDU > Subject: Re: [LINUX-390] Adding disk to root LVM with RHEL 7 > > Looks like you did everything right: online, dasdfmt, fdasd, lvextend, > vgextend, and using "1" instead of the whole disk (because it's ECKD and > requires the VTOC). > > The first block where you get an error is 16380912. Maybe that's a clue? > Looks like cylinder #109206 (150 4K blocks per ECKD cyl). Someone check > my math? And the (new) root FS looks like 110100 cyls. > The VG has two disks, correct? How big are they? > So where is this troublesome block in the grand scheme? > > I don't recall resizing a filesystem *down*, but I think it can be done. > I'm always nervous about that last block (or several) in any filesystem, > any backing store (CKD, FBA, SCSI/SAN), anymode (LVM, partitioned, whole). > Never know when the system or some program will walk to the end "just > because". > > -- R; <>< > > > On 4/15/20 10:58 AM, Martha McConaghy wrote: > > I have servers that I'm setting up with RHEL 7.8 on ECKD disk. I > installed it with root in an LVM, all of that worked fine. Now, I'm > testing adding a 2nd ECKD disk to the LVM as I know that will be required > in the future, but I'm running into a confusing problem. Everything works > as I expect and the disk space shows up in / as it should. When I reboot > the server, however, it goes to heck and ends up in emergency mode. The > most prominent feature of the console are a bunch of I/O errors on device > dm-2, which is the disk I just added. Below are the steps I followed to > add the disk. Before doing this, I had activated the disk, added it to > /etc/dasd.conf and run zipl. After doing that, I rebooted to ensure that > the disk came up online, which it did. So, I'm confident that the disk is > there when the system rebooted the 2nd time. > > > > I have a lot of colleagues who work with Linux all the time, but don't > usually have root as an LVM. They haven't seen this problem before, but > they work mainly on X. Could this be specific problem to using ECKD? I > have thought of going to an FBA LUN, but had spare ECKD to use. > > > > Martha > > > > > > [root@opncl42 ~]# cio_ignore -r 0.0.0200 > > [root@opncl42 ~]# chccwdev --online 0.0.0200 > > Setting device 0.0.0200 online > > Done > > [root@opncl42 ~]# lsdasd > > Bus-ID Status Name Device Type BlkSz Size Blocks > > > ============================================================================== > > 0.0.0150 active dasda 94:0 ECKD 4096 46068MB 11793420 > > 0.0.0200 active dasdb 94:4 ECKD 4096 23033MB 5896620 > > [root@opncl42 ~]# vi /etc/dasd.conf > > [root@opncl42 ~]# zipl > > Using config file '/etc/zipl.conf' > > Building bootmap in '/boot' > > Building menu 'zipl-automatic-menu' > > Adding #1: IPL section '3.10.0-1127.el7.s390x' (default) > > Adding #2: IPL section '3.10.0-1127.el7.s390x_with_debugging' > > Adding #3: IPL section 'linux' > > Preparing boot device: dasda (0150). > > Done. > > [root@opncl42 ~]# reboot > > --------------------------------------------------- > > [root@opncl42 ~]# lsdasd > > Bus-ID Status Name Device Type BlkSz Size Blocks > > > ============================================================================== > > 0.0.0150 active dasda 94:0 ECKD 4096 46068MB 11793420 > > 0.0.0200 active dasdb 94:4 ECKD 4096 23033MB 5896620 > > > > [root@opncl42 ~]# dasdfmt -p -f /dev/dasdb > > Please enter the blocksize of the formatting [4096]: > > Drive Geometry: 32759 Cylinders * 15 Heads = 491385 Tracks > > > > I am going to format the device /dev/dasdb in the following way: > > Device number of device : 0x200 > > Labelling device : yes > > Disk label : VOL1 > > Disk identifier : 0X0200 > > Extent start (trk no) : 0 > > Extent end (trk no) : 491384 > > Compatible Disk Layout : yes > > Blocksize : 4096 > > Mode : Full > > > > --->> ATTENTION! <<--- > > All data of that device will be lost. > > Type "yes" to continue, no will leave the disk untouched: yes > > Formatting the device. This may take a while (get yourself a coffee). > > cyl 32759 of 32759 |#################################|100% [2m 43s] > > Finished formatting the device. > > Rereading the partition table... ok > > [root@opncl42 ~]# pvcreate /dev/dasdb1 > > Device /dev/dasdb1 not found. > > [root@opncl42 ~]# fdasd /dev/dasdb > > reading volume label ..: VOL1 > > reading vtoc ..........: ok > > > > Command action > > m print this menu > > p print the partition table > > n add a new partition > > d delete a partition > > v change volume serial > > t change partition type > > r re-create VTOC and delete all partitions > > u re-create VTOC re-using existing partition sizes > > s show mapping (partition number - data set name) > > q quit without saving changes > > w write table to disk and exit > > > > Command (m for help): n > > First track (1 track = 48 KByte) ([2]-491384): > > Using default value 2 > > Last track or +size[c|k|M] (2-[491384]): > > Using default value 491384 > > > > Command (m for help): w > > writing VTOC... > > rereading partition table... > > [root@opncl42 ~]# pvcreate /dev/dasdb1 > > Physical volume "/dev/dasdb1" successfully created. > > [root@opncl42 ~]# vgdisplay > > --- Volume group --- > > VG Name rhel_opncl41 > > System ID > > Format lvm2 > > Metadata Areas 1 > > Metadata Sequence No 3 > > VG Access read/write > > VG Status resizable > > MAX LV 0 > > Cur LV 2 > > Open LV 2 > > Max PV 0 > > Cur PV 1 > > Act PV 1 > > VG Size <44.50 GiB > > PE Size 4.00 MiB > > Total PE 11391 > > Alloc PE / Size 11381 / <44.46 GiB > > Free PE / Size 10 / 40.00 MiB > > VG UUID uEvApZ-Wrx7-7n47-f0f0-IQ6R-uU4K-JO8wAN > > > > [root@opncl42 ~]# vgextend rhel_opncl41 /dev/dasdb1 > > Volume group "rhel_opncl41" successfully extended > > [root@opncl42 ~]# vgdisplay > > --- Volume group --- > > VG Name rhel_opncl41 > > System ID > > Format lvm2 > > Metadata Areas 2 > > Metadata Sequence No 5 > > VG Access read/write > > VG Status resizable > > MAX LV 0 > > Cur LV 2 > > Open LV 2 > > Max PV 0 > > Cur PV 2 > > Act PV 2 > > VG Size <66.99 GiB > > PE Size 4.00 MiB > > Total PE 17149 > > Alloc PE / Size 11381 / <44.46 GiB > > Free PE / Size 5768 / 22.53 GiB > > VG UUID uEvApZ-Wrx7-7n47-f0f0-IQ6R-uU4K-JO8wAN > > > > [root@opncl42 ~]# lvdisplay > > --- Logical volume --- > > LV Path /dev/rhel_opncl41/swap > > LV Name swap > > VG Name rhel_opncl41 > > LV UUID QzWFVP-Z5hz-gRV2-ORnb-4rR6-pdhM-d77w3n > > LV Write Access read/write > > LV Creation host, time opncl41, 2020-04-14 20:25:30 -0400 > > LV Status available > > # open 2 > > LV Size 4.50 GiB > > Current LE 1152 > > Segments 1 > > Allocation inherit > > Read ahead sectors auto > > - currently set to 8192 > > Block device 253:1 > > > > --- Logical volume --- > > LV Path /dev/rhel_opncl41/root > > LV Name root > > VG Name rhel_opncl41 > > LV UUID G0Gy3F-lvt2-2uZy-3BKr-9yHL-uVqe-1lfycV > > LV Write Access read/write > > LV Creation host, time opncl41, 2020-04-14 20:25:30 -0400 > > LV Status available > > # open 1 > > LV Size <39.96 GiB > > Current LE 10229 > > Segments 1 > > Allocation inherit > > Read ahead sectors auto > > - currently set to 8192 > > Block device 253:0 > > > > [root@opncl42 ~]# lvextend -l +5768 /dev/rhel_opncl41/root > > Size of logical volume rhel_opncl41/root changed from <39.96 GiB > (10229 extents) to <62.49 GiB (15997 extents). > > Logical volume rhel_opncl41/root successfully resized. > > [root@opncl42 ~]# lvdisplay > > --- Logical volume --- > > LV Path /dev/rhel_opncl41/swap > > LV Name swap > > VG Name rhel_opncl41 > > LV UUID QzWFVP-Z5hz-gRV2-ORnb-4rR6-pdhM-d77w3n > > LV Write Access read/write > > LV Creation host, time opncl41, 2020-04-14 20:25:30 -0400 > > LV Status available > > # open 2 > > LV Size 4.50 GiB > > Current LE 1152 > > Segments 1 > > Allocation inherit > > Read ahead sectors auto > > - currently set to 8192 > > Block device 253:1 > > > > --- Logical volume --- > > LV Path /dev/rhel_opncl41/root > > LV Name root > > VG Name rhel_opncl41 > > LV UUID G0Gy3F-lvt2-2uZy-3BKr-9yHL-uVqe-1lfycV > > LV Write Access read/write > > LV Creation host, time opncl41, 2020-04-14 20:25:30 -0400 > > LV Status available > > # open 1 > > LV Size <62.49 GiB > > Current LE 15997 > > Segments 2 > > Allocation inherit > > Read ahead sectors auto > > - currently set to 8192 > > Block device 253:0 > > > > [root@opncl42 ~]# df -h > > Filesystem Size Used Avail > Use% Mounted on > > devtmpfs 9.8G 0 9.8G > 0% /dev > > tmpfs 9.8G 0 > 9.8G 0% /dev/shm > > tmpfs 9.8G 0 > 9.8G 0% /sys/fs/cgroup > > /dev/mapper/rhel_opncl41-root 40G 2.0G 38G 5% / > > /dev/dasda1 494M 136M 359M 28% /boot > > tmpfs 2.0G 0 2.0G > 0% /run/user/1000 > > > > [root@opncl42 ~]# fsadm resize /dev/mapper/rhel_opncl41-root > > meta-data=/dev/mapper/rhel_opncl41-root isize=256 agcount=4, > agsize=2618624 blks > > = sectsz=4096 attr=2, projid32bit=1 > > = crc=0 finobt=0 spinodes=0 > > data = bsize=4096 blocks=10474496, imaxpct=25 > > = sunit=0 swidth=0 blks > > naming =version 2 bsize=4096 ascii-ci=0 ftype=0 > > log =internal bsize=4096 blocks=5114, version=2 > > = sectsz=4096 sunit=1 blks, lazy-count=1 > > realtime =none extsz=4096 blocks=0, rtextents=0 > > data blocks changed from 10474496 to 16380928 > > > > [root@opncl42 ~]# df -h > > Filesystem Size Used Avail > Use% Mounted on > > devtmpfs 9.8G 0 9.8G > 0% /dev > > tmpfs 9.8G 0 > 9.8G 0% /dev/shm > > tmpfs 9.8G 8.3M > 9.8G 1% /run > > tmpfs 9.8G 0 > 9.8G 0% /sys/fs/cgroup > > /dev/mapper/rhel_opncl41-root 63G 2.0G 61G 4% / > > /dev/dasda1 494M 136M 359M 28% /boot > > tmpfs 2.0G 0 2.0G > 0% /run/user/1000 > > [root@opncl42 ~]# reboot > > > > > ---------------------------------------------------------------------------- > > Last part of console as it goes into emergency mode: > > > > 13 Ý Ý32m OK Ý0m¨ Started File System Check on > /dev/mapper/rhel_opncl41-root. > > 14 Ý Ý32m OK Ý0m¨ Started dracut initqueue hook. > > 15 Mounting /sysroot... > > 16 Ý Ý32m OK Ý0m¨ Reached target Remote File Systems (Pre). > > 17 Ý Ý32m OK Ý0m¨ Reached target Remote File Systems. > > 18 Ý 123.794007¨ Buffer I/O error on dev dm-2, logical block 16380912, > async page read > > 19 Ý Ý1;31mFAILED Ý0m¨ Failed to mount /sysroot. > > 20 See 'systemctl status sysroot.mount' for details. > > 21 Ý Ý1;33mDEPEND Ý0m¨ Dependency failed for Initrd Root File System. > > 22 Ý Ý1;33mDEPEND Ý0m¨ Dependency failed for Reload Configuration from > the Real Root. > > 23 Ý Ý32m OK Ý0m¨ Stopped dracut pre-udev hook. > > 24 Ý Ý32m OK Ý0m¨ Stopped dracut cmdline hook. > > 25 Ý Ý32m OK Ý0m¨ Reached target Initrd File Systems. > > 26 Ý Ý32m OK Ý0m¨ Stopped target Basic System. > > 27 Ý Ý32m OK Ý0m¨ Stopped target System Initialization. > > 28 Ý Ý32m OK Ý0m¨ Stopped dracut initqueue hook. > > 29 Ý Ý32m OK Ý0m¨ Started Emergency Shell. > > 30 Ý Ý32m OK Ý0m¨ Reached target Emergency Mode. > > 31 > > 32 Generating "/run/initramfs/rdsosreport.txt" > > 33 Ý 123.845595¨ Buffer I/O error on dev dm-2, logical block 16380912, > async > > page read > > 34 Ý 123.846240¨ Buffer I/O error on dev dm-2, logical block 16380912, > async > > page read > > 35 > > 36 > > 37 Entering emergency mode. Exit the shell to continue. > > 38 Type "journalctl" to view system logs. > > 39 You might want to save "/run/initramfs/rdsosreport.txt" to a USB > stick or / > > boot > > 40 after mounting them and attach it to a bug report. > > 41 > > 42 > > 43 :/# > > ------------------------------------------------ > > Information from Journalctl while in emergency mode: > > > > ÝKApr 15 02:21:42 opncl42 systemdÝ1¨: Reached target Basic System. Ým > > Apr 15 02:21:42 opncl42 kernel: Ý1;31mnetif_napi_add() called with > weight 128 o > > n devic Ým > > Apr 15 02:21:42 opncl42 kernel: qeth 0.0.0700: MAC address > 02:01:42:00:00:08 suc > > Ým > > Apr 15 02:21:42 opncl42 kernel: qeth 0.0.0700: Device is a Virtual NIC > QDIO card > > Ým > > with link type Virt.NIC QDIO (portname: > ) Ým > > Apr 15 02:23:45 opncl42 dracut-initqueueÝ398¨: Warning: dracut-initqueue > timeout > > Ým > > Apr 15 02:23:45 opncl42 kernel: Ý1;31mBuffer I/O error on dev dm-2, > logical blo > > ck 1638 Ým > > Apr 15 02:23:45 opncl42 systemdÝ1¨: Found device > /dev/mapper/rhel_opncl41-root. > > Ým > > Apr 15 02:23:45 opncl42 systemdÝ1¨: Starting File System Check on > /dev/mapper/rh > > Ým > > Apr 15 02:23:45 opncl42 systemd-fsckÝ2026¨: fsck: error 2 (No such file > or direc > > Ým > > Apr 15 02:23:45 opncl42 systemd-fsckÝ2026¨: Ý1;31mfsck failed with > error code 8 > > . Ý0m Ým > > Apr 15 02:23:45 opncl42 systemd-fsckÝ2026¨: Ý1;39mIgnoring error. Ý0m Ým > > Apr 15 02:23:45 opncl42 systemdÝ1¨: Started File System Check on > /dev/mapper/rhe > > Ým > > Apr 15 02:23:45 opncl42 kernel: Ý1;31mBuffer I/O error on dev dm-2, > logical blo > > ck 1638 Ým > > Apr 15 02:23:45 opncl42 systemdÝ1¨: Started dracut initqueue hook. Ým > > Apr 15 02:23:45 opncl42 systemdÝ1¨: Mounting /sysroot... Ým > > Apr 15 02:23:45 opncl42 systemdÝ1¨: Reached target Remote File Systems > (Pre). Ým > > > > Apr 15 02:23:45 opncl42 systemdÝ1¨: Reached target Remote File Systems. > Ým > > Apr 15 02:23:45 opncl42 mountÝ2042¨: mount: you must specify the > filesystem type > > Ým > > Apr 15 02:23:45 opncl42 systemdÝ1¨: Ý1;39msysroot.mount mount process > exited, c > > ode=exi Ým > > Apr 15 02:23:45 opncl42 systemdÝ1¨: Ý1;31mFailed to mount /sysroot. Ý0m > Ým > > Apr 15 02:23:45 opncl42 systemdÝ1¨: Ý1;39mDependency failed for Initrd > Root Fil > > e Syste Ým > > Apr 15 02:23:45 opncl42 systemdÝ1¨: Ý1;39mDependency failed for Reload > Configur > > ation f Ým > > Ý7mlines 193-215 Ý27m ÝK ÝKApr 15 02:23:45 opncl42 systemdÝ1¨: > Ý1;39mJob ini > > Ým > > Apr 15 02:23:45 opncl42 kernel: Ý1;31mBuffer I/O error on dev dm-2, > logical blo > > ck 1638 Ým > > Apr 15 02:23:45 opncl42 systemdÝ1¨: Received SIGRTMIN+21 from PID 406 > (plymouthd > > Ým > > Apr 15 02:23:45 opncl42 kernel: Ý1;31mBuffer I/O error on dev dm-2, > logical blo > > ck 1638 Ým > > Apr 15 02:23:45 opncl42 kernel: Ý1;31mBuffer I/O error on dev dm-2, > logical blo > > ck 1638 Ým > > Ý7mlines 211-233/233 (END) Ý27m ÝK ÝK ÝK Ý7mlines 211-233/233 (END) > Ý27m ÝK > > > > > > > > > > > > Martha McConaghy > > > > Marist: System Architect/Technical Lead > > > > SHARE Association: Vice President > > > > Marist College IT > > > > Poughkeepsie, NY 12601 > > > > ---------------------------------------------------------------------- > > For LINUX-390 subscribe / signoff / archive access instructions, > > send email to lists...@vm.marist.edu with the message: INFO LINUX-390 > or visit > > http://www2.marist.edu/htbin/wlvindex?LINUX-390 > > > -- > -- R; <>< > > > ---------------------------------------------------------------------- > For LINUX-390 subscribe / signoff / archive access instructions, > send email to lists...@vm.marist.edu with the message: INFO LINUX-390 or > visit > http://www2.marist.edu/htbin/wlvindex?LINUX-390 > > ---------------------------------------------------------------------- > For LINUX-390 subscribe / signoff / archive access instructions, > send email to lists...@vm.marist.edu with the message: INFO LINUX-390 or > visit > http://www2.marist.edu/htbin/wlvindex?LINUX-390 > > ---------------------------------------------------------------------- > For LINUX-390 subscribe / signoff / archive access instructions, > send email to lists...@vm.marist.edu with the message: INFO LINUX-390 or > visit > http://www2.marist.edu/htbin/wlvindex?LINUX-390 > > ---------------------------------------------------------------------- For LINUX-390 subscribe / signoff / archive access instructions, send email to lists...@vm.marist.edu with the message: INFO LINUX-390 or visit http://www2.marist.edu/htbin/wlvindex?LINUX-390 ---------------------------------------------------------------------- For LINUX-390 subscribe / signoff / archive access instructions, send email to lists...@vm.marist.edu with the message: INFO LINUX-390 or visit http://www2.marist.edu/htbin/wlvindex?LINUX-390
