On Fri, Jan 20, 2006 at 04:27:50PM +0100, Janosch Machowinski wrote:
Sometimes I'm stupid. Try this version instead.
Okay, this worked,
the outprut from your little programm was 0x500,
but it should be
GPE0_BLK: 0x00000428
GPE1_BLK: 0x00000000
So is this an error in ACPI-CA or in my DSDT ?
From the ich4-m specification (see
ftp://download.intel.com/design/mobile/datashts/25233701.pdf
)
and the lspci -xxx I've requested, we can look that, for the isa
bridge, we can see that 0x500 is the base address for the GPIO
configuration registers.
The lspci show us:
00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface
Bridge (rev 03)
Flags: bus master, medium devsel, latency 0
00: 86 80 cc 24 0f 01 80 02 03 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 01 04 00 00 10 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 01 05 00 00 10 00 00 00
60: 0b 04 0a 05 90 00 00 00 80 80 80 0a 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: ff fc 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 28 03 00 00 00 00 00 00 0d 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 80 02 02 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 02 28 00 00 02 cf 00 00 04 00 00 00 00 00 00 00
e0: 12 00 00 c0 00 00 06 34 33 22 11 00 00 00 67 45
f0: 00 00 01 00 00 00 00 00 60 0f 03 00 00 00 80 02
The GPIO base address is at 0x58-0x5b (see page 305).
From page 396 (9.10 General Purpose I/O Registers) we'll
learn that the ACPI node INV7 correspond to the
8th bit of the 'GPIO signal invert (GPI_INV)' register.
Therefore actually INV7 control somehow we'll treat
what happens under the GPE0_BLK, but do not modify it.
(I must confess I don't see why the ODM designed
that stuff like this).
At the description of this register, and for bit 8, we'll
see that setting this bit will have no effect if the
corresponding GPIO is set as an output. We'll therefore
shall check if that is the problem.
Could you please (again, sorry!)
Don't be sorry to debug my notebook ;-)
run the next tool attached?
This would help to progress a little bit further.
scotchmobil pmtools # ./scan_gpio_ctl
00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f
0500 bf 39 00 1a ff ff 00 00 00 00 00 00 00 00 01 08
0510 00 00 00 00 00 00 00 00 00 00 00 02 00 00 00 00
0520 00 00 00 00 00 00 00 00 00 00 00 00 88 39 00 00
0530 ff 0f 00 00 06 04 00 00 8f 04 00 00 00 00 00 00
-
To unsubscribe from this list: send the line "unsubscribe linux-acpi" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
