On Thursday 10 August 2006 15:36, Andi Kleen wrote:
> PIC mode is an outdated way to drive the APICs that was used on
> some early MP boards. It is not supported in the ACPI model.
>
> It is unlikely to be ever configured by any x86-64 system
>
> Remove it thus.
Is there any reason we can't entirely remove MPS from x86_64?
(asside from the routines that ACPI uses)
-Len
> Signed-off-by: Andi Kleen <[EMAIL PROTECTED]>
>
> ---
> arch/x86_64/kernel/apic.c | 92
> +++++++++++++------------------------------
> arch/x86_64/kernel/mpparse.c | 8 ---
> arch/x86_64/kernel/smpboot.c | 1
> include/asm-x86_64/mpspec.h | 1
> include/asm-x86_64/smp.h | 1
> 5 files changed, 29 insertions(+), 74 deletions(-)
>
> Index: linux/arch/x86_64/kernel/apic.c
> ===================================================================
> --- linux.orig/arch/x86_64/kernel/apic.c
> +++ linux/arch/x86_64/kernel/apic.c
> @@ -136,72 +136,40 @@ void clear_local_APIC(void)
> apic_read(APIC_ESR);
> }
>
> -void __init connect_bsp_APIC(void)
> -{
> - if (pic_mode) {
> - /*
> - * Do not trust the local APIC being empty at bootup.
> - */
> - clear_local_APIC();
> - /*
> - * PIC mode, enable APIC mode in the IMCR, i.e.
> - * connect BSP's local APIC to INT and NMI lines.
> - */
> - apic_printk(APIC_VERBOSE, "leaving PIC mode, enabling APIC
> mode.\n");
> - outb(0x70, 0x22);
> - outb(0x01, 0x23);
> - }
> -}
> -
> void disconnect_bsp_APIC(int virt_wire_setup)
> {
> - if (pic_mode) {
> - /*
> - * Put the board back into PIC mode (has an effect
> - * only on certain older boards). Note that APIC
> - * interrupts, including IPIs, won't work beyond
> - * this point! The only exception are INIT IPIs.
> - */
> - apic_printk(APIC_QUIET, "disabling APIC mode, entering PIC
> mode.\n");
> - outb(0x70, 0x22);
> - outb(0x00, 0x23);
> - }
> - else {
> - /* Go back to Virtual Wire compatibility mode */
> - unsigned long value;
> -
> - /* For the spurious interrupt use vector F, and enable it */
> - value = apic_read(APIC_SPIV);
> - value &= ~APIC_VECTOR_MASK;
> - value |= APIC_SPIV_APIC_ENABLED;
> - value |= 0xf;
> - apic_write(APIC_SPIV, value);
> -
> - if (!virt_wire_setup) {
> - /* For LVT0 make it edge triggered, active high,
> external and enabled */
> - value = apic_read(APIC_LVT0);
> - value &= ~(APIC_MODE_MASK | APIC_SEND_PENDING |
> - APIC_INPUT_POLARITY | APIC_LVT_REMOTE_IRR |
> - APIC_LVT_LEVEL_TRIGGER | APIC_LVT_MASKED );
> - value |= APIC_LVT_REMOTE_IRR | APIC_SEND_PENDING;
> - value = SET_APIC_DELIVERY_MODE(value, APIC_MODE_EXTINT);
> - apic_write(APIC_LVT0, value);
> - }
> - else {
> - /* Disable LVT0 */
> - apic_write(APIC_LVT0, APIC_LVT_MASKED);
> - }
> + /* Go back to Virtual Wire compatibility mode */
> + unsigned long value;
>
> - /* For LVT1 make it edge triggered, active high, nmi and
> enabled */
> - value = apic_read(APIC_LVT1);
> - value &= ~(
> - APIC_MODE_MASK | APIC_SEND_PENDING |
> + /* For the spurious interrupt use vector F, and enable it */
> + value = apic_read(APIC_SPIV);
> + value &= ~APIC_VECTOR_MASK;
> + value |= APIC_SPIV_APIC_ENABLED;
> + value |= 0xf;
> + apic_write(APIC_SPIV, value);
> +
> + if (!virt_wire_setup) {
> + /* For LVT0 make it edge triggered, active high, external and
> enabled */
> + value = apic_read(APIC_LVT0);
> + value &= ~(APIC_MODE_MASK | APIC_SEND_PENDING |
> APIC_INPUT_POLARITY | APIC_LVT_REMOTE_IRR |
> - APIC_LVT_LEVEL_TRIGGER | APIC_LVT_MASKED);
> + APIC_LVT_LEVEL_TRIGGER | APIC_LVT_MASKED );
> value |= APIC_LVT_REMOTE_IRR | APIC_SEND_PENDING;
> - value = SET_APIC_DELIVERY_MODE(value, APIC_MODE_NMI);
> - apic_write(APIC_LVT1, value);
> + value = SET_APIC_DELIVERY_MODE(value, APIC_MODE_EXTINT);
> + apic_write(APIC_LVT0, value);
> + } else {
> + /* Disable LVT0 */
> + apic_write(APIC_LVT0, APIC_LVT_MASKED);
> }
> +
> + /* For LVT1 make it edge triggered, active high, nmi and enabled */
> + value = apic_read(APIC_LVT1);
> + value &= ~(APIC_MODE_MASK | APIC_SEND_PENDING |
> + APIC_INPUT_POLARITY | APIC_LVT_REMOTE_IRR |
> + APIC_LVT_LEVEL_TRIGGER | APIC_LVT_MASKED);
> + value |= APIC_LVT_REMOTE_IRR | APIC_SEND_PENDING;
> + value = SET_APIC_DELIVERY_MODE(value, APIC_MODE_NMI);
> + apic_write(APIC_LVT1, value);
> }
>
> void disable_local_APIC(void)
> @@ -418,7 +386,7 @@ void __cpuinit setup_local_APIC (void)
> * TODO: set up through-local-APIC from through-I/O-APIC? --macro
> */
> value = apic_read(APIC_LVT0) & APIC_LVT_MASKED;
> - if (!smp_processor_id() && (pic_mode || !value)) {
> + if (!smp_processor_id() && !value) {
> value = APIC_DM_EXTINT;
> apic_printk(APIC_VERBOSE, "enabled ExtINT on CPU#%d\n",
> smp_processor_id());
> } else {
> @@ -1096,8 +1064,6 @@ int __init APIC_init_uniprocessor (void)
>
> verify_local_APIC();
>
> - connect_bsp_APIC();
> -
> phys_cpu_present_map = physid_mask_of_physid(boot_cpu_id);
> apic_write(APIC_ID, SET_APIC_ID(boot_cpu_id));
>
> Index: linux/arch/x86_64/kernel/mpparse.c
> ===================================================================
> --- linux.orig/arch/x86_64/kernel/mpparse.c
> +++ linux/arch/x86_64/kernel/mpparse.c
> @@ -56,7 +56,6 @@ struct mpc_config_intsrc mp_irqs[MAX_IRQ
> int mp_irq_entries;
>
> int nr_ioapics;
> -int pic_mode;
> unsigned long mp_lapic_addr = 0;
>
>
> @@ -514,13 +513,6 @@ void __init get_smp_config (void)
> printk(KERN_INFO "Using ACPI for processor (LAPIC)
> configuration information\n");
>
> printk("Intel MultiProcessor Specification v1.%d\n",
> mpf->mpf_specification);
> - if (mpf->mpf_feature2 & (1<<7)) {
> - printk(KERN_INFO " IMCR and PIC compatibility mode.\n");
> - pic_mode = 1;
> - } else {
> - printk(KERN_INFO " Virtual Wire compatibility mode.\n");
> - pic_mode = 0;
> - }
>
> /*
> * Now see if we need to read further.
> Index: linux/include/asm-x86_64/mpspec.h
> ===================================================================
> --- linux.orig/include/asm-x86_64/mpspec.h
> +++ linux/include/asm-x86_64/mpspec.h
> @@ -178,7 +178,6 @@ extern int mp_irq_entries;
> extern struct mpc_config_intsrc mp_irqs [MAX_IRQ_SOURCES];
> extern int mpc_default_type;
> extern unsigned long mp_lapic_addr;
> -extern int pic_mode;
>
> #ifdef CONFIG_ACPI
> extern void mp_register_lapic (u8 id, u8 enabled);
> Index: linux/include/asm-x86_64/smp.h
> ===================================================================
> --- linux.orig/include/asm-x86_64/smp.h
> +++ linux/include/asm-x86_64/smp.h
> @@ -33,7 +33,6 @@ extern cpumask_t cpu_initialized;
>
> extern void smp_alloc_memory(void);
> extern volatile unsigned long smp_invalidate_needed;
> -extern int pic_mode;
> extern void lock_ipi_call_lock(void);
> extern void unlock_ipi_call_lock(void);
> extern int smp_num_siblings;
> Index: linux/arch/x86_64/kernel/smpboot.c
> ===================================================================
> --- linux.orig/arch/x86_64/kernel/smpboot.c
> +++ linux/arch/x86_64/kernel/smpboot.c
> @@ -1090,7 +1090,6 @@ void __init smp_prepare_cpus(unsigned in
> /*
> * Switch from PIC to APIC mode.
> */
> - connect_bsp_APIC();
> setup_local_APIC();
>
> if (GET_APIC_ID(apic_read(APIC_ID)) != boot_cpu_id) {
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to [EMAIL PROTECTED]
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
-
To unsubscribe from this list: send the line "unsubscribe linux-acpi" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
