Hi Chris,
> Hi Subhash, Arindam,
>
> On Wed, Aug 10 2011, Subhash Jadavani wrote:
>> Here is Essential conditions to indicate Version 3.00 Card
>> (SD_SPEC=2 and SD_SPEC3=1) :
>> (1) The card shall support CMD6
>> (2) The card shall support CMD8
>> (3) The card shall support CMD42
>> (4) User area capacity shall be up to 2GB (SDSC) or 32GB (SDHC)
>> User area capacity shall be more than or equal to 32GB and
>> up to 2TB (SDXC)
>> (5) Speed Class shall be supported (SDHC or SDXC)
>>
>> So even if SD card doesn't support any of the newly defined
>> UHS-I bus speed mode, it can advertise itself as SD3.0 cards
>> as long as it supports all the essential conditions of
>> SD3.0 cards. Given this, these type of cards should atleast
>> run in High Speed mode @50MHZ if it supports HS.
>>
>> But current initialization sequence for SD3.0 cards is
>> such that these non-UHS-I SD3.0 cards runs in Default
>> Speed mode @25MHz.
>>
>> This patch makes sure that these non-UHS-I SD3.0 cards run
>> in High Speed Mode @50MHz.
>>
>> Tested this patch with SanDisk Extreme SDHC 8GB Class 10 card.
>>
>> Signed-off-by: Subhash Jadavani <[email protected]>
>> ---
>> drivers/mmc/core/sd.c | 6 +++---
>> 1 files changed, 3 insertions(+), 3 deletions(-)
>>
>> diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c
>> index ff27741..e2dcf23 100644
>> --- a/drivers/mmc/core/sd.c
>> +++ b/drivers/mmc/core/sd.c
>> @@ -306,6 +306,9 @@ static int mmc_read_switch(struct mmc_card *card)
>> goto out;
>> }
>>
>> + if (status[13] & 0x02)
>> + card->sw_caps.hs_max_dtr = 50000000;
>> +
>> if (card->scr.sda_spec3) {
>> card->sw_caps.sd3_bus_mode = status[13];
>>
>> @@ -348,9 +351,6 @@ static int mmc_read_switch(struct mmc_card *card)
>> }
>>
>> card->sw_caps.sd3_curr_limit = status[7];
>> - } else {
>> - if (status[13] & 0x02)
>> - card->sw_caps.hs_max_dtr = 50000000;
>> }
>>
>> out:
>
> The patch itself is fine, but please could one of you add some #defines
> for the status response bit names and their possible values inside
> mmc_read_switch()? It's looking a bit opaque.
>
> (I know that this patch doesn't introduce any of these magic numbers;
> I just think that now is a good time to add documentation for them.)
For UHS-I bus speed modes,we already have macros for bus speed modes under
include/linux/mmc/card.h:
#define UHS_SDR12_BUS_SPEED 0
#define UHS_SDR25_BUS_SPEED 1
#define UHS_SDR50_BUS_SPEED 2
#define UHS_SDR104_BUS_SPEED 3
#define UHS_DDR50_BUS_SPEED 4
There are only 2 non-uhs-i bus speed mode options:
high speed and default speed.
So,
status[13] = 2 => High speed mode
status[13] = 1 => Default speed mode
If you want, i can add 2 more macros for HS and DS modes. Do you want me
to define these macros within mmc_read_switch() or under sd_switch_caps
struct in include/linux/mmc/card.h file?
Regards,
Subhash
>
> Thanks very much,
>
> - Chris.
> --
> Chris Ball <[email protected]> <http://printf.net/>
> One Laptop Per Child
>
--
Sent by a consultant of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
