On Aug 14, 2014, at 11:18 AM, Lina Iyer <lina.i...@linaro.org> wrote:
> On Thu, Aug 14, 2014 at 11:09:48AM -0500, Kumar Gala wrote:
>>
>> On Aug 12, 2014, at 2:43 PM, Lina Iyer <lina.i...@linaro.org> wrote:
>>
>>>
>>> diff --git a/Documentation/devicetree/bindings/arm/msm/spm-v2.txt
>>> b/Documentation/devicetree/bindings/arm/msm/spm-v2.txt
>>> new file mode 100644
>>> index 0000000..3130f4b
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/arm/msm/spm-v2.txt
>>> @@ -0,0 +1,62 @@
>>> +* MSM Subsystem Power Manager (spm-v2)
>>> +
>>> +S4 generation of MSMs have SPM hardware blocks to control the Application
>>> +Processor Sub-System power. These SPM blocks run individual state machine
>>> +to determine what the core (L2 or Krait/Scorpion) would do when the WFI
>>> +instruction is executed by the core.
>>> +
>>> +The devicetree representation of the SPM block should be:
>>> +
>>> +Required properties
>>> +
>>> +- compatible: Could be one of -
>>> + "qcom,spm-v2.1"
>>> + "qcom,spm-v3.0"
>>> +- reg: The physical address and the size of the SPM's memory mapped
>>> registers
>>> +- qcom,cpu: phandle for the CPU that the SPM block is attached to. On
>>> targets
>>> + that dont support CPU phandles the driver would support qcom,core-id.
>>> + This field is required on only for SPMs that control the CPU.
>>> +- qcom,saw2-cfg: SAW2 configuration register
>>
>> Can we change this to qcom,saw2-clk-div as that is what is really getting
>> set, I know there are a few other fields in the saw2-cfg register, but I’m
>> pretty sure we arent ever really setting those from DT.
>>
> I am pruning them off in the next revision of the patch.
>>> +- qcom,saw2-spm-dly: Provides the values for the SPM delay command in the
>>> SPM
>>> + sequence
>>> +- qcom,saw2-spm-ctl: The SPM control register
>>
>> Can we describe this as “spm-enable”, “spm-inhibit-start-address”,
>> “spm-wakeup-cfg”?
>>
>> Also, I’m unclear why would we have a case that spm would be disabled?
>>
> Much of these registers names make it easier for developers and
> debuggers to relate it to the hardware spec. Choosing different names
> here though might make it readable would convolute their efforts.
The point is to move away from just dumping a register value directly from DT
into the device. This is pretty bad form. The names can relate to the
register, etc, its just the fields that are really being used/set was the
direction I was suggesting we go.
>
>>> +- qcom,name: The name with which a SPM device is identified by the power
>>> + management code.
>>> +
>>> +Optional properties
>>> +
>>> +- qcom,saw2-pmic-data0..7: Specify the pmic data value and the associated
>>> FTS
>>> + (Fast Transient Switch) index to send the PMIC data to
>>> +- qcom,vctl-port: The PVC (PMIC Virtual Channel) port used for changing
>>> + voltage
>>> +- qcom,phase-port: The PVC port used for changing the number of phases
>>> +- qcom,pfm-port: The PVC port used for enabling PWM/PFM modes
>>> +- qcom,saw2-spm-cmd-wfi: The WFI command sequence
>>> +- qcom,saw2-spm-cmd-ret: The Retention command sequence
>>> +- qcom,saw2-spm-cmd-spc: The Standalone PC command sequence
>>> +- qcom,saw2-spm-cmd-pc-no-rpm: The Power Collapse command sequence where
>>> APPS
>>> + proc won't inform the RPM.
>>> +- qcom,saw2-spm-cmd-pc: The Power Collapse command sequence. This sequence
>>> may
>>> + turn off other SoC components.
>>> +- qcom,saw2-spm-cmd-gdhs: GDHS (Globally Distributed Head Switch) command
>>> + sequence. This sequence will retain the memory but turn off the logic.
>>> +- qcom,cpu-vctl-list: List of cpu node phandles, whose voltage the spm
>>> device
>>> + can control.
>>> +- qcom,vctl-timeout-us: The timeout value in microseconds to wait for
>>> voltage to
>>> + change after sending the voltage command to the PMIC.
>>> +-
>>> +Example:
>>> + qcom,spm@f9089000 {
>>> + compatible = "qcom,spm-v2";
>>> + #address-cells = <1>;
>>> + #size-cells = <1>;
>>> + reg = <0xf9089000 0x1000>;
>>> + qcom,cpu = <&CPU0>;
>>> + qcom,saw2-cfg = <0x1>;
>>> + qcom,saw2-spm-dly= <0x20000400>;
>>> + qcom,saw2-spm-ctl = <0x1>;
>>> + qcom,saw2-spm-cmd-wfi = [03 0b 0f];
>>> + qcom,saw2-spm-cmd-spc = [00 20 50 80 60 70 10 92
>>> + a0 b0 03 68 70 3b 92 a0 b0
>>> + 82 2b 50 10 30 02 22 30 0f];
>>> + };
>>
>> --
>> Employee of Qualcomm Innovation Center, Inc.
>> Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by
>> The Linux Foundation
>>
- k
--
Employee of Qualcomm Innovation Center, Inc.
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by
The Linux Foundation
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
