On 2017/10/6 下午6:42, Michael Lyle wrote:
> Coly--
>
> Holy crap, I'm not surprised you don't see a difference if you're
> writing with 512K size! The potential benefit from merging is much
> less, and the odds of missing a merge is much smaller. 512KB is 5ms
> sequential by itself on a 100MB/sec disk--- lots more time to wait to
> get the next chunks in order, and even if you fail to merge the
> potential benefit is much less-- if the difference is mostly
> rotational latency from failing to merge then we're talking 5ms vs
> 5+2ms.
>
Hi Mike,
This is how wars happend LOL :-)
> Do you even understand what you are trying to test?
When I read patch 4/5, I saw you mentioned 4KB writes:
"e.g. at "background" writeback of target rate = 8, it would not combine
two adjacent 4k writes and would instead seek the disk twice."
And when we talked about patch 5/5, you mentioned 1MB writes:
"- When writeback rate is medium, it does I/O more efficiently. e.g.
if the current writeback rate is 10MB/sec, and there are two
contiguous 1MB segments, they would not presently be combined. A 1MB
write would occur, then we would increase the delay counter by 100ms,
and then the next write would wait; this new code would issue 2 1MB
writes one after the other, and then sleep 200ms. On a disk that does
150MB/sec sequential, and has a 7ms seek time, this uses the disk for
13ms + 7ms, compared to the old code that does 13ms + 7ms * 2. This
is the difference between using 10% of the disk's I/O throughput and
13% of the disk's throughput to do the same work."
Then I assume the bio reorder patches should work well for write size
from 4KB to 1MB. Also I think "hmm, if the write size is smaller, there
will be less chance for dirty blocks to be contiguous on cached device",
then I choose 512KB.
Here is my command line to setup the bcache:
make-bcache -B <cached device> -C <cache device>
echo <cache device> > /sys/fs/bcache/register
echo <cached device> > /sys/fs/bcache/register
sleep 1
echo 0 > /sys/block/bcache0/bcache/cache/congested_read_threshold_us
echo 0 > /sys/block/bcache0/bcache/cache/congested_write_threshold_us
echo writeback > /sys/block/bcache0/bcache/cache_mode
echo 0 > /sys/block/bcache0/bcache/writeback_running
Now writeback is disabled, I start to use fio to write dirty data on
cache device. The following is fio job file.
[global]
direct=1
thread=1
ioengine=libaio
[job]
filename=/dev/bcache0
readwrite=randwrite
numjobs=8
;blocksize=64k
blocksize=512k
;blocksize=1M
iodepth=128
size=3000G
time_based=1
;runtime=10m
ramp_time=4
gtod_reduce=1
randrepeat=1
ramp_time, gtod_reduce and randrepeat are what I copied from your fio
example.
Then I watch the dirty data amount, when the dirty increases to a target
number (half full example), I kill fio process.
Then I start writeback by
echo 1 > /sys/block/bcache0/bcache/writeback_running
and immediately run 2 bash scripts to collect performance data:
1) writeback_rate.sh
while [ 1 ];do
cat /sys/block/bcache0/bcache/writeback_rate_debug
echo -e "\n\n"
sleep 60
done
2) iostat command line
iostat -x 1 <cache device> <cached device> <more disks compose md
device> | tee iostat.log
The writeback rate debug information is collected every 1 minute, iostat
information is collected every 1 seconds. They are all dedicated disks
for testing, just raw disks without any file system.
Thanks.
Coly
> On Fri, Oct 6, 2017 at 3:36 AM, Coly Li <[email protected]> wrote:
>> On 2017/10/6 下午5:20, Michael Lyle wrote:
>>> Coly--
>>>
>>> I did not say the result from the changes will be random.
>>>
>>> I said the result from your test will be random, because where the
>>> writeback position is making non-contiguous holes in the data is
>>> nondeterministic-- it depends where it is on the disk at the instant
>>> that writeback begins. There is a high degree of dispersion in the
>>> test scenario you are running that is likely to exceed the differences
>>> from my patch.
>>
>> Hi Mike,
>>
>> I did the test quite carefully. Here is how I ran the test,
>> - disable writeback by echo 0 to writeback_runing.
>> - write random data into cache to full or half size, then stop the I/O
>> immediately.
>> - echo 1 to writeback_runing to start writeback
>> - and record performance data at once
>>
>> It might be random position where the writeback starts, but there should
>> not be too much difference of statistical number of the continuous
>> blocks (on cached device). Because fio just send random 512KB blocks
>> onto cache device, the statistical number of contiguous blocks depends
>> on cache device vs. cached device size, and how full the cache device is
>> occupied.
>>
>> Indeed, I repeated some tests more than once (except the md raid5 and md
>> raid0 configurations), the results are quite sable when I see the data
>> charts, no big difference.
>>
>> If you feel the performance result I provided is problematic, it would
>> be better to let the data talk. You need to show your performance test
>> number to prove that the bio reorder patches are helpful for general
>> workloads, or at least helpful to many typical workloads.
>>
>> Let the data talk.
>>
>> Thanks.
>>
>> --
>> Coly Li
