On 04/19/2018 10:18 PM, Omar Sandoval wrote:
> On Thu, Apr 19, 2018 at 01:44:41PM -0600, Jens Axboe wrote:
>> On 4/19/18 1:41 PM, Bart Van Assche wrote:
>>> On Thu, 2018-04-19 at 12:13 -0700, Omar Sandoval wrote:
>>>> On Thu, Apr 19, 2018 at 11:53:30AM -0700, Omar Sandoval wrote:
>>>>> Thanks for the test! Applied.
>>>>
>>>> Side note, it's unfortunate that this test takes 180 seconds to run only
>>>> because we have to wait for the command timeout. We should be able to
>>>> export request_queue->rq_timeout writeable in sysfs. Would you be
>>>> interested in doing that?
>>>
>>> Hello Omar,
>>>
>>> Is this perhaps what you are looking for?
>>> # ls -l /sys/class/scsi_device/*/*/timeout
>>> -rw-r--r-- 1 root root 4096 Apr 19 08:52
>>> /sys/class/scsi_device/2:0:0:0/device/timeout
>>> -rw-r--r-- 1 root root 4096 Apr 19 12:39
>>> /sys/class/scsi_device/8:0:0:1/device/timeout
>>
>> We should have it generically available though, not just for SCSI. In
>> retrospect, it should have been under queue/ from the start, now we'll
>> end up with duplicate entries for SCSI.
>
> For the sake of this test, I just decreased the timeout through SCSI.
Great idea.
> echo 5 > "/sys/block/${SCSI_DEBUG_DEVICES[0]}/device/timeout"
However, the timeout should be sufficiently larger than scsi_debug/delay,
in order not to run into the command timeout.
It may be unfortunate that scsi_debug/delay uses jiffies as unit and
can thus differ in a range of an order of magnitude for different kernel
configs.
> # delay to reduce response repetition: around 1..10sec depending on HZ
> echo 1000 > /sys/bus/pseudo/drivers/scsi_debug/delay
On s390, we typically have HZ=100, so 1000 jiffies are 10 seconds.
We can increase the sdev cmd timeout or decrease the scsi_debug/delay.
100 instead of 1000 for scsi_debug/delay worked for me;
but for some reason the loop checking for busy did not work (any more?)
causing an unexpected test case error:
> # ./check scsi/004
> scsi/004 (ensure repeated TASK SET FULL results in EIO on timing out command)
> [failed]
> runtime 31.892s ... 31.720s
> --- tests/scsi/004.out 2018-04-16 11:47:19.105931872 +0200
> +++ results/nodev/scsi/004.out.bad 2018-04-23 14:07:33.615445253
> +0200
> @@ -1,3 +1,3 @@
> Running scsi/004
> -Input/output error
> +modprobe: FATAL: Module scsi_debug is in use.
> Test complete
so I added another sleep hack:
# dd closing SCSI disk causes implicit TUR also being delayed once
+ # sleep over time window where READ was done and TUR not yet queued
+ sleep 2
while grep -q -F "in_use_bm BUSY:"
"/proc/scsi/scsi_debug/${SCSI_DEBUG_HOSTS[0]}"; do
What do you think?
--
Mit freundlichen Grüßen / Kind regards
Steffen Maier
Linux on z Systems Development
IBM Deutschland Research & Development GmbH
Vorsitzende des Aufsichtsrats: Martina Koederitz
Geschaeftsfuehrung: Dirk Wittkopp
Sitz der Gesellschaft: Boeblingen
Registergericht: Amtsgericht Stuttgart, HRB 243294
